Christie Roadie HD+35K User Manual page 77

Input 5 Key (OPT.1)
Press the I
NPUT
typically is the standard factory-installed Dual SD/HD-SDI Module. If PIP is enabled, press INPUT 5 to
assign it as the PIP source. Note, if there are two inputs connected to this module, the second input (B) is
considered to be INPUT 7 and can be most easily accessed with INPUT 7. Or, if you are using the built-in
keypad or the optional "lite" remote, neither of which have a separate I
INPUT 7 as follows:
• While displaying from INPUT 5, press the I
• While displaying from any input other than the Dual SD/HD-SDI Module, press the I
switches to either INPUT 5 or INPUT 7, depending on which of the Dual SD/HD-SDI Module inputs (A or
B) was last used. Press the I
Input 6 Key (OPT.2)
Press the I
NPUT
enabled, press INPUT 6 to assign it as the PIP source. If the Dual SD/HD-SDI Module is installed here, and
there are two inputs connected, its second input (B) is considered INPUT 8 and can be most easily accessed
with I
NPUT 8. Or, if you are using the built-in keypad or the optional "lite" remote, neither of which have a
separate I
NPUT
key, use INPUT 6 to access INPUT 8 as follows:
• While displaying from INPUT 6, press INPUT 6 again to switch to INPUT 8.
• While displaying from any input other than the Dual SD/HD-SDI Module, press I
either INPUT 6 or INPUT 8, depending on which of the Dual SD/HD-SDI Module inputs (A or B) was last
used. Press I
NPUT
Input Key (Standard IR Remote Only)
Press I + n (where n = 1, 2, 3, 4, 5, or 6; 7 and 8 optional) as an alternative method for selecting which
NPUT
source to display. Six source locations are identified with input numbers on the projector's input panel. The last
two, 7 and 8, require the Dual SD/HD-SDI Module installed in either of the option slots.
If PIP is enabled, I
(primary) image source.
The I
NPUT
NOTE:
Menu Preferences
prefer to enter the desired source location "blind", i.e. without on-screen feedback. Refer to
Preferences
Contrast Key
Press the C
ONT
Arrow key or D
NOTE: For best results, start low and increase so that whites remain bright, but are not distorted or tinted, and
that light areas do not become white (i.e., "crushed"). Conversely, low contrast causes dim images. Refer
to 3.6.3 Image Settings Menu
Brightness Key
Press the B
RIGHT
L and R
EFT IGHT
so that dark areas do not become black (i.e., "crushed"). Conversely, overly high brightness changes black to
dark gray, and causes washed-out images. Refer to
Roadie HD+35K User Manual
020-100340-02 Rev. 1 (01-2010)
5 key to display from the INPUT 5 interface module installed in the
5 key again to display from the other Dual SD/HD-SDI Module input.
NPUT
6 key to display from the INPUT 6 interface module installed in the
again to display from the other Dual SD/HD-SDI Module input.
+ n changes the PIP (secondary) image source, and I
NPUT
key behavior depends on whether or not the Display Channel List option is selected in the
menu. You can choose to have on-screen feedback when you press I
.
key on the standard IR remote to change the amount of white in your images. Use the UP
OWN
Arrow key until you reach the desired level of white.
(Image Settings subsection).
key on the standard IR remote to increase or decrease the amount of black in the image. Use
Arrow keys until you reach the desired level of black. For best results, start high and decrease
5 key again. This switches to INPUT 7.
NPUT
3.6.3 Image Settings Menu
Section 3: Operation
Option 1
NPUT
key, use INPUT 5 to access
5 key. This
NPUT
Option 2
NPUT
. This switches to
+ PIP + n changes the main
NPUT
NPUT
( Image Settings subsection ).
slot, which
slot. If PIP is
, or you may
Menu
3-11