Lexus 2005 IS300 User Manual page 1002

Wheel bearing backlash
Front axle F t l
Axle hub deviation
Upper ball joint turning torque
Lower ball joint excessive play
F Front suspension t i
Lower ball joint turning torque
Stabilizer bar link ball joint turning torque
Wheel bearing backlash
R Rear axle l
Axle hub deviation
Drive shaft standard length
Rear drive shaft
Upper ball joint turning torque
Toe control link ball joint turning torque
Rear suspension Rear sus ension
Stabilizer bar link ball joint turning torque
Companion flange vertical runout
Companion flange lateral runout
Ring gear runout
Ring gear backlash
Drive pinion bearing (at starting)
Total preload (at starting)
Rear differential Rear differential
Side gear backlash (2 pinion differential)
Differential case runout
Side gear shaft oil seal drive in depth
Front oil seal drive in depth
Right and left side gear shafts standard distance
Pinion gear backlash adjusting thrust washer
Rear differential Drive pinion bearing adjusting washer thickness
2005 LEXUS IS300 (RM1140U)
SERVICE SPECIFICATIONS
New bearing
Reused bearing
- SUSPENSION AND AXLE
Maximum 0.05 mm (0.0020 in.)
Maximum 0.05 mm (0.0020 in.)
1.0 - 3.4 N·m (10 - 35 kgf·cm, 9 - 30 in.·lbf)
Maximum 0.9 mm (0.035 in.)
0.5 - 3.0 N·m (5 - 30 kgf·cm, 0.4 - 26 in.·lbf)
0.05 - 1.9 N·m (0.5 - 20 kgf·cm, 0.4 - 16 in.·lbf)
Maximum 0.05 mm (0.0020 in.)
Maximum 0.07 mm (0.0028 in.)
RH:
LH:
1.0 - 2.9 N·m (10 - 30 kgf·cm, 9 - 26 in.·lbf)
1.0 - 2.5 N·m (10 - 25 kgf·cm, 9 - 22 in.·lbf)
0.05 - 1.0 N·m (0.5 - 10 kgf·cm, 0.4 - 9.0 in.·lbf)
Maximum 0.09 mm (0.0035 in.)
Maximum 0.09 mm (0.0035 in.)
Maximum 0.07 mm (0.0028 in.)
Maximum 0.13 - 0.18 mm (0.0051 - 0.0071 in.)
0.98 - 1.57 N·m (10 - 16 kgf·cm, 8.7 - 13.9 in.·lbf)
0.49 - 0.78 N·m (5 - 8 kgf·cm, 4.3 - 6.9 in.·lbf)
Drive pinion preload plus
0.39 - 0.59 N·m (4 - 6 kgf·cm, 3.5 - 5.2 in.·lbf)
0.05 - 0.20 mm (0.0020 - 0.0079 in.)
Maximum 0.07 mm (0.0028 in.)
0 ± 0.50 mm (0 ± 0.0197 in.)
2.00 ± 0.45 mm (0.0787 ± 0.0177 in.)
279.7 mm (11.012 in.) or less
1.6 mm (0.062 in.)
1.7 mm (0.067 in.)
1.8 mm (0.071 in.)
1.70 mm (0.0669 in.)
1.73 mm (0.0681 in.)
1.76 mm (0.0693 in.)
1.79 mm (0.0704 in.)
1.82 mm (0.0717 in.)
1.85 mm (0.0729 in.)
1.88 mm (0.0740 in.)
1.91 mm (0.0752 in.)
1.94 mm (0.0764 in.)
1.97 mm (0.0776 in.)
2.00 mm (0.0787 in.)
2.03 mm (0.0799 in.)
2.06 mm (0.0811 in.)
2.09 mm (0.0822 in.)
2.12 mm (0.0835 in.)
2.15 mm (0.0847 in.)
2.18 mm (0.0858 in.)
2.21 mm (0.0870 in.)
2.24 mm (0.0882 in.)
2.27 mm (0.0894 in.)
2.30 mm (0.0906 in.)
2.33 mm (0.0918 in.)
Author :
SS-35
585.4 ± 5.0 mm (23.047 ± 0.197 in.)
539.8 ± 5.0 mm (21.252 ± 0.197 in.)
Date :
177