IBM System Storage TS3310 Setup And Operator Manual page 338

Diagnostic Resolution (continued)
DR030 11-43
DR031 11-43
DR032 11-44
DR033 11-44
DR034 11-44
DR035 11-45
DR036 11-45
Diagnostic Resolutions 11-1, 11-34
dimensions of tape library 1-16
DNS 8-6
Doors
Access 1-3
DR001 11-34
DR002 11-35
DR003 11-35
DR004 11-35
DR005 11-35
DR006 11-36
DR007 11-36
DR009 11-37
DR010 11-37
DR011 11-38
DR012 11-38
DR014 11-39
DR015 11-39
DR018 11-40
DR019 11-40
DR020 11-40
DR021 11-41
DR022 11-41
DR024 11-41
DR026 11-42
DR028 11-42
DR029 11-43
DR030 11-43
DR031 11-43
DR032 11-44
DR033 11-44
DR034 11-44
DR035 11-45
DR036 11-45
Drive 1-5
channel calibration 1-9
control path failure 11-44
coordinates 1-14
determining SCSI and Fibre Channel
IDs 2-4
general diagnostic 11-36
LEDs 10-10
load failure 11-43
loss of communication 11-43
manually clean 11-40
power management 1-9
remove 12-16
sled not auto leveling 11-44
speed matching 1-9
unload diagnostic 11-35
drive dump 8-17
drive sled
description 1-8
remove/replace 12-16
drives 8-15
adding control path 8-16
capturing a dump 8-17
dumps 8-17
fibre channel IDs 2-5
X-2
TS3310 Tape Library Setup and Operator Guide
drives (continued)
IDs 8-16
loading 8-15
modifying fibre settings 8-16
online/offline 8-16
SCSI IDs 2-4
unloading 8-15
viewing information 8-15
E
email 8-6
environment 1-17
operating 1-17
particulates 1-17
Error codes
Service Action Tickets 11-1
error messages
viewing 8-11
Error messages
operator intervention 10-2
errors
obtaining from library and
drives A-1
RS/6000 A-1
errpt command, using A-1
expansion module 1-3
connectivity diagnostic 11-37
remove from 14U library 12-11
remove/replace 12-11
replace in 14U library 12-11
F
feature licenses
capacity expansion 1-9
control path failover 1-9, 1-12
data path failover 1-9, 1-12
path failover 1-9, 1-12
features
optional 1-8
capacity expansion 1-9
drives 1-8
firmware update by IBM service
personnel 1-12
license keys 1-9
path failover 1-12
redundant power supply 1-9
Fibre Channel
drive IDs 2-5
supported topologies 2-6
Fibre Channel drive
compatibility with Multi-Path
Architecture 1-16
Fibre Channel interface 2-10
cables and speeds 2-10
connectors and adapters 2-11
LUN assignments 2-7
persistent binding 2-11
sharing on a SAN 2-11
World Wide names 2-7
zoning 2-10
firmware
upgrades 8-12
Firmware
drive 8-13, 8-14
Firmware (continued)
FMR cartridge 8-14
creating 8-14
library 8-12
updating
using Fibre Channel
interface 8-14
using ITDT Tool 8-13
using SCSI interface 8-14
foot pads
remove 12-28
replace 12-28
front panel
access door 1-3
control module 1-2
expansion module 1-3
I/O Station 1-3
Operator Panel 1-4
power button 1-4
G
gear rack alignment 12-13
glossary F-1
H
height of tape library 1-16
host
sharing library 1-16
hp-ux system error information A-9
I
I/O slots
assign 8-4
assigning 7-5
I/O Station 1-3
close door 11-41
lock diagnostic 11-38
locking/unlocking 8-12
IBM Ultrium Tape Drive 1-8
install planning 2-1
installation 3-1
cabling a 5U library 3-32, 4-21
cabling a library with SCSI
drives 3-33, 4-22
cabling the library 3-32, 4-21
desktop 4-7
identifying desktop configuratin 4-7
identifying location 3-14
installing a drive 3-30, 4-18
installing a power supply 3-31, 4-20
installing components removed for
weight reduction 3-29
planning 2-1
powering on the library 3-37, 4-26
rack 3-5, 3-6, 3-12, 3-14, 3-18, 3-27,
3-29, 3-30, 3-31, 4-5, 4-6, 4-18, 4-20
rack ears 3-27
rails 3-18
reducing library weight 3-5, 4-5
removing drive 3-6, 4-6
removing power supply 3-5, 4-5
unpacking shipment 3-1, 4-1
verifying kit contents 3-12