Ikegami Editcam 3 DNS-33W Operation Manual page 87

4. As in the Normal Menu, rotate the rotary pulse switch,
put the flashing cursor on the detailed setting item to set
up, and then press the SET button to confirm the selected
item for submenus.
Submenu
BARS TITLE/MODE
DISPLAY
POSITION
TITLE
BARS MODE
BARS TITLE/MODE
DISPLAY
POSITION
TITLE
BARS MODE
When the detailed setting items are confirmed, the
flashing cursor moves to the mode selection field (ON/
OFF, etc.).
5. Select the mode by rotating the rotary pulse switch, and
press the SET button to confirm the selection. Each time
the SET button is pressed, the flashing cursor switches to
detailed setting item → mode selection → detailed setting
item → mode selection and so on.
6. To exit from submenu, press the VF CHARA button, or
select the title on top of the screen ("BARS TITLE/
MODE" in the figures above).
7. To end the Normal Menu, return to the initial screen of
the Normal Menu, then press the VF CHARA button.
Notice
• If the Maintenance Menu is displayed by mistake
during setup by the Normal Menu, press the VF
CHARA button again, exit from the menu mode
and retry the Normal Menu operations. The
Maintenance Menu is displayed by pressing and
holding VF CHARA button for more than two
seconds and then pressing the SET button.
Please note that even if the Maintenance Menu is
displayed, it is not abnormality or trouble in the
camera setting mode.
• If the mode setting is selected but not confirmed,
the change in that setting may be cancelled.
5. SETTINGS AND ADJUSTMENT OF CAMERA
OFF
RIGHT
( )
NORMAL
OFF
RIGHT
( )
NORMAL
DNS-33W 0503 VOL1 (E)
Operation of the "Maintenance Menu"
This section explains how to operate the Maintenance Menu.
There are 3 screens for the Maintenance Menu: "***MENU
[1/3]***", "***MENU [2/3]***", and "***MENU [3/3]***".
Their operation procedures are basically the same as the
Normal Menu.
Maintenance Menu (1/3)
＊＊＊MENU [ 1/3 ]＊＊＊
VF DISPLAY
MONITOR OUT
ZEBRA INDICATOR
!INDICATOR
BARS TITLE / MODE
LOW / MID / HIGH GAIN MODE
BATT/DISK WARNING
SCENE FILE
LEVEL ADJUST
Maintenance Menu (2/3)
＊＊＊MENU [ 3/3 ]＊＊＊
OTHERS
INFORMATION
MENU CUSTOMIZE
1. Press and hold the VF CHARA button on the right side
of the camera for more than 2 seconds, and then press the
SET button on the front part, with the VF CHARA button
still held. Press the VF CHARA button to end the
Maintenance Menu.
2. Rotate the rotary pulse switch and put the flashing cursor
on the menu item to set up.
3. Press the SET button to confirm the selected item.
When the selected item is confirmed, the screen
automatically switches to the submenu screen, and
detailed setting items can be modified there.
4. As in the Maintenance Menu, rotate the rotary pulse
switch and put the flashing cursor on the detailed setting
item to set up, then press the SET button to confirm the
selected item.
5. Select the mode by rotating the rotary pulse switch, and
press the SET button to confirm the selection. Each time
the SET button is pressed, the flashing cursor switches to
detailed setting item → mode selection → detailed setting
item → mode selection and so on.
6. To exit from submenu, press the VF CHARA button or
select the title on top of the screen to confirm.
7. To end the Maintenance Menu, return to the initial screen of
the Maintenance Menu and press the VF CHARA button.
5 - 13
Maintenance Menu (2/3)
＊＊＊MENU [ 2/3 ]＊＊＊
CPU SYSTEM CONTROL
AWB / ABB MODE
AUTO IRIS SET
G.L. PHASE ADJUST
LENS SELECT
EXT VTR REC CONTROL
VIDEO PROCESS MODE
MEMORY CARD
SCREEN ASPECT MODE
DNS-33W