Ikegami Editcam 3 DNS-33W Operation Manual page 103

FILTER AWB MEM
(AWB memory setting for each filter)
The AWB memory settings can be changed for each filter.
Setting Value
OFF
2 AWB memories, A/B can be used
ON
2 AWB memories A/B for each ECC filter, 8 in
total can be used
AWB REFERENCE
Select "ON" when using the user setting as AWB
convergence value. When set to "OFF", the GAIN in R and
Bch will be adjusted so that it will match the level in Gch.
In normal operation, set to "OFF".
REFERENCE SET
(Creating reference data to use as the
convergence value when AWB/ABB is
activated)
Stores reference for AWB/ABB in the memory.
Setting Value
AWB The current white balance status is stored in the
memory as the convergence value.
ABB
The current black balance status is stored in the
memory as the convergence value.
Adjust the GAIN (R, B) or PEDESTAL (R, G, B) accurately
using the remote controller, etc. Rotate the rotary pulse
switch to select "AWB" or "ABB" and press the SET button
to confirm. "PUSH SET -> START" message is displayed.
To cancel, press the VF CHARA button to exit from the
camera setting mode. To execute, press the SET button again.
The reference data is created. The created reference data is
stored in the memory.
"MEASURING ..." is displayed, and the creation of the
reference data starts. When creation is complete,
"COMPLETED" is displayed. If the level measurement of
white/black level fails, "MEASURE ERROR" will be
displayed. If the miss-operation prevention function is
activated, "UNABLE TO EXECUTE" will be displayed, and
this operation will not be executed.
Notice
This function cannot be activated if the S2 switch
(red slide-switch) of MPU module is not set to "ON"
(at the top). To prevent miss-operation, the S2
switch is set to "OFF" (at the bottom), to prevent
unintentional update of the reference files.
5. SETTINGS AND ADJUSTMENT OF CAMERA
Description
Description
DNS-33W 0503 VOL1 (E)
5.10.17 AUTO IRIS SET
(Setting the auto iris operation)
IRIS LEVEL SET
[B4 Mount Lens]
Sets the level and response characteristics of auto iris
function. To always obtain the best video level even if the
amount of light changes, the iris must be controlled. Set
"IRIS SET MODE" to "ON" first. This will enable the setting
of the "IRIS LEVEL SET", "PEAK RATIO SET", "IRIS
GAIN", and "IRIS SPEED" described below.
AUTO IRIS SET
IRIS SET MODE
IRIS LEVEL SET
PEAK RATIO SET
IRIS GAIN
IRIS SPEED
IRIS LIMIT
LENS ADJUST
1. Select "IRIS LEVEL SET".
2. Shoot the gray scale chart with the camera, adjust the
value of "IRIS LEVEL SET" by the rotary pulse switch
so that the video level becomes 100%.
3. Select "IRIS GAIN", put your hand before the camera,
pan the camera etc. to adjust the "IRIS GAIN" by the
rotary pulse switch, so that the IRIS does not hunt even
if the video level is changed rapidly.
The default value of "IRIS GAIN" is set to "50". The
operation speed of the auto iris is set that "1" is slow and
"100" is fast. Hunting tends to occur more often as the
value goes up. Set it to the default value "50" as long as
hunting is not occurring.
4. Select "IRIS SPEED", put your hand before the camera,
pan the camera etc. to adjust the "IRIS SPEED" by the
rotary pulse switch, so that the proper iris convergence
speed can be obtained even if the video level is changed
rapidly. The default value of "IRIS SPEED" is set to
"50". The operation speed of the auto iris is set that "1"
is slow and "100" is fast.
5 - 29
OFF
0
0
50
50
F22
OFF
DNS-33W