Ikegami Editcam 3 DNS-33W Operation Manual page 90

5 - 16 5. SETTINGS AND ADJUSTMENT OF CAMERA
5.10.3 VF DISPLAY (Selecting various status
display modes on the VF)
VF DISPLAY sets up items and contents displayed on the
VF, for example turning ON/OFF the markers, etc.
DISPLAY MODE
DISPLAY MODE selects the display mode of various
characters providing the camera setting information. Depending
on the selected mode, the characters are displayed as follows:
Setting Value
OFF
Displays no characters except the alarm
messages.
1
Displays the area/center/frame marker and the
record time count/audio level indicator at all
times. Also, when any of the following switches
is operated, the corresponding setting status is
displayed for approximately 2 seconds:
• ND FILTER knob
• ECC FILTER SELECT switch
• GAIN SELECT switch
• AWB SELECT switch
• SHUTT/SUP-V switch
• EXTENDER SELECT lever
Displays the area/center/frame marker, the record
2
time count/audio level indicator, and filter
positions at all times. Also, when any of the
following switches is operated, the corresponding
setting status is displayed for approximately 2
seconds if the set item is of a default
setting/value, and displayed at all times if the set
item is not a default value:
• GAIN SELECT switch (default: 0dB)
• AWB SELECT switch (default: Ach)
• SHUTT/SUP-V switch (default: OFF)
1. Select "VF DISPLAY" from the Normal Menu and
confirm the selection.
The submenu screen is displayed.
2. Select "DISPLAY MODE" from the submenus and
confirm the selection.
The flashing cursor moves to the mode setting column.
3. Select "OFF", "1", or "2" and confirm the selection.
SAFETY AREA, SAFETY MARKER, SAFETY
ASPECT
The safety markers are used to check the safety area zone
within the screen. Select "ACTION" (displays action area), or
"TITLE" (displays the title area) from "SAFETY AREA".
"SAFETY MARKER" turns ON/OFF the safety marker
display, and "SAFETY ASPECT" selects the aspect ratio of
the safety markers from 4:3, 13:9, 14:9, 15:9, and 16:9.
DNS-33W
Description
DNS-33W 0503 VOL1 (E)
Area Name
Action safety zone, which is equivalent to
Action area
90% of the height and width of the screen.
Title area
Title safety zone, which is equivalent to
80% of the height and width of the screen.
CENTER MARKER
Select "ON" or "OFF" from the "CENTER MARKER" and
confirm.
FRAME MARKER, FRAME ASPECT, SIDE
MASK
Turn the frame marker display ON/OFF by "FRAME
MARKER", and select the aspect ratio of the frame marker
display from 4:3, 13:9, 14:9, 15:9, and 16:9 by "FRAME
ASPECT".
SIDE MASK is the function that converts the video level of
the picture outside the frame marker. "SIDE MASK" selects
a switch ON/OFF of the SIDE MASK. Video level of the
SIDE MASK is adjusted by "SIDE MASK LVL" of "VF
DISPLAY2".
Notice
• The area markers (area, center, frame markers)
displayed on the VF can all be turned ON/OFF at
the same time. Press and hold VF CHARA button
and rotate the rotary pulse switch. The screen
switches to setting mode for turning ON/OFF the
area marker display, and the ON/OFF setting can
be changed (when the screen switches to the
setting mode, the VF CHARA button can be
released). At this time, the current setting appears
on the character display of the VF. If the setting
mode screen is left as is for approximately 3
seconds after selecting the mode, the setting
mode ends automatically. There are three ways to
end the marker display setting mode: pressing the
SET button, pressing the VF CHARA button again,
and leaving as is for more than 3 seconds.
• Note that if all the area marker display settings are
set to "OFF", no area markers will be displayed on
the VF. If the area marker display settings for
each marker is not set to "ON" mode, selecting
"1" or "2" in "DISPLAY MODE" submenu will not
display the markers.
TITLE Area
ACTION Area
Description