Ikegami Editcam 3 DNS-33W Operation Manual page 91

VF DISPLAY2 (Submenus to select mode for
various displays on the VF)
VF DISPLAY2 sets up the item contents to display on the
VF, for example the brightness of the marker display, etc.
[OUTPUT SIGNAL]
OUTPUT SIGNAL selects the video signal type (Y or
R+G+B) displayed on the VF.
1. Select "OUTPUT SIGNAL", and rotate the rotary pulse
switch to select "Y" or "R+G+B".
Selecting "R+G+B" will display a blue subject better on
the VF, but at the same time increases the noise.
2. Confirm the selection by pressing the SET button.
[MARKER/CHAR LVL]
MARKER/CHAR LVL sets up the brightness of the marker/
character display.
1. Select "MARKER/CHAR LVL", and rotate the rotary
pulse switch to adjust to the required value.
2. Confirm the value by pressing the SET button.
[SIDE MASK LVL]
SIDE MASK LVL sets up the brightness of the side mask
display. The side mask function changes the video level of
the picture outside the frame marker, therefore this menu is
displayed only when the FRAME MARKER is ON.
1. Select "SIDE MASK LVL", and rotate the rotary pulse
switch to adjust to the required value.
2. Confirm the value by pressing the SET button.
[ZEBRA IND LVL]
ZEBRA IND LVL sets up the brightness of the zebra
indicators.
1. Select "ZEBRA IND LVL", and rotate the rotary pulse
switch to adjust to the required value.
2. Confirm the value by pressing the SET button.
[VF DTL LVL]
VF DTL LVL sets up the amount of DTL displayed on the
VF.
1. Select "VF DTL LVL", and rotate the rotary pulse switch
to adjust to the required value.
2. Confirm the value by pressing the SET button.
5. SETTINGS AND ADJUSTMENT OF CAMERA
DISPLAY SELECT (Character display setting)
DISPLAY SELECT turns each character display ON/OFF.
1. Select "DISPLAY SELECT". The following submenu
screen is displayed.
2. The setting item is displayed in the parenthesis, and its
character display flashes. Rotate the rotary pulse switch
and select an item to be set.
3. Press the SET button, rotate the rotary pulse switch, and
select from "ON" and "OFF" of the display.
4. Press the SET button to confirm the selection.
5. In "VF CHAR SW" submenu, the character display setting
when the VF CHARA button is pressed can be specified.
Setting Value
SEL-ON
ALL-ON
6. Rotate the rotary pulse switch to select the setting item,
and press the SET button to confirm the selection.
5.10.4 MONITOR OUT
(Selecting mode for various display
items on the monitor line)
MONITOR OUT sets up the items displayed on the video
output on the monitor and their contents, for example turning
ON/OFF the marker display, etc.
VIDEO SELECT
VIDEO SELECT selects the video signal channel output on
the MON OUT connector.
1. Select "VIDEO SELECT", and rotate the rotary pulse
switch to adjust to the required value.
Setting Value
CAMERA
RET VIDEO
2. Confirm the value by pressing the SET button.
DNS-33W 0503 VOL1 (E)
EX RETRO 00:00:00:00 S#- 0001
DISPLAY SELECT
QUIT
( SHUTT/SUP-V : ON )
VF CHAR SW ALL-ON
A: 3.2K B: 3.2K
60
+ 6dB
1A A
12.0V F16 1/100
Description
Displays only the setting items set to "ON".
Displays all the setting items regardless of
ON/OFF setting.
MONITOR OUT
VIDEO SELECT CAMERA
ENC
OUTPUT SIGNAL
OFF
SAFETY MARKER
CENTER MARKER OFF
FRAME MARKER OFF
SIDE MASK OFF
CHARACTER IND ON
ZEBRA IND OFF
MARKER/CHAR LVL 65
MONITOR OUT2
Description
To be output video signal of the camera
To be output RET video signal
5 - 17
DNS-33W