Ikegami Editcam 3 DNS-33W Operation Manual page 92

5 - 18 5. SETTINGS AND ADJUSTMENT OF CAMERA
OUTPUT SIGNAL
OUTPUT SIGNAL selects the video signal channel (ENC, Y,
R+G+B, R, G, or B) displayed on the MON connector.
1. Select "OUTPUT SIGNAL", and rotate the rotary pulse
switch to select a signal to be set.
2. Confirm the selection by pressing the SET button.
Notice
This setting is valid only while the power is turned
ON. If the power is turned OFF, this setting returns
to "ENC".
SAFETY MARKER
The safety markers are used to check the safety area zone
within the screen. The safety marker setting ("ACTION" or
"TITLE") and the aspect ratio are the same as set in the "VF
DISPLAY" submenu.
1. Select "SAFETY MARKER", and rotate the rotary pulse
switch to set "ON" or "OFF".
2. Confirm the selection by pressing the SET button.
CENTER MARKER
CENTER MARKER turn ON/OFF the center marker display
on the monitor.
Select "ON" or "OFF" from "CENTER MARKER" and
confirm.
FRAME MARKER
FRAME MARKER turns ON/OFF the frame marker display
on the monitor.
Select "ON" or "OFF" from "FRAME MARKER" and
confirm.
SIDE MASK
SIDE MASK turns ON/OFF the side mask on the monitor.
Select "ON" or "OFF" from "SIDE MASK" and confirm.
CHARACTER IND
CHARACTER IND turns ON/OFF the character indicators on
the monitor.
Select "ON" or "OFF" from "CHARACTER IND" and
confirm.
ZEBRA IND
ZEBRA IND turns ON/OFF the zebra indicators on the
monitor.
Select "ON" or "OFF" from "ZEBRA IND" and confirm.
MARKER/CHAR LVL
MARKER/CHAR LVL sets up the brightness of the marker/
character display on the monitor.
1. Select "MARKER/CHAR LVL", and rotate the rotary
pulse switch to adjust to the required value.
2. Confirm the value by pressing the SET button.
DNS-33W
MONITOR OUT2
(Submenus to select mode for various
displays on the monitor line)
MONITOR OUT2 sets up the item contents to display on the
monitor, for example the brightness of the marker display, etc.
[SIDE MASK LVL]
SIDE MASK LVL sets up the brightness of the side mask
display. The side mask function changes the video level of
the picture outside the frame marker, therefore this menu is
displayed only when the FRAME MARKER is "ON".
1. Select "SIDE MASK LVL", and rotate the rotary pulse
switch to adjust to the required value.
2. Confirm the value by pressing the SET button.
[ZEBRA IND LVL]
ZEBRA IND LVL sets up the brightness of the zebra
indicators.
1. Select "ZEBRA IND LVL", and rotate the rotary pulse
switch to adjust to the required value.
2. Confirm the value by pressing the SET button.
5.10.5 ZEBRA INDICATOR
The zebra signals are striped patterns that appear
superimposed on the actual picture. There are two zebra
signals: the zebra 1 signal which appears in the area where
the video level is higher than the value set in "ZEBRA1
DETECT", and the zebra 2 signal which appears only in the
area where the video level is the same as the value set in
"ZEBRA2 DETECT".
The type of striped pattern displayed for zebra 1 and zebra 2
are different.
The zebra 1 signals appear as thin slanting stripes streaming
towards the top right corner of the screen, while the zebra 2
signals appear as wider slanting stripes streaming slower
towards the bottom right corner of the screen.
The zebra 1 signal is used to manage the tone of the whole
screen, and the zebra 2 signal is used to manage the tone of
a part of screen, which involves colors in memory, for
example the face tone. The following describes the
procedures.
DNS-33W 0503 VOL1 (E)
MONITOR OUT2
SIDE MASK LVL 50
ZEBRA IND LVL 20
ZEBRA INDICATOR
ZEBRA1 IND ON
ZEBRA1 DETECT 100%
ZEBRA2 IND
OFF
ZEBRA2 DETECT 70%