Ikegami Editcam 3 DNS-33W Operation Manual page 93

Setting the Zebra 1 Signal
1. Select "ZEBRA 1 IND", and rotate the rotary pulse
switch to select "ON".
2. Confirm the selection by pressing the SET button.
3. Select "ZEBRA 1 DETECT", and rotate the rotary pulse
switch to adjust to the required value.
4. Confirm the value by pressing the SET button.
Setting the Zebra 2 Signal
1. Select "ZEBRA 2 IND", and rotate the rotary pulse
switch to select "ON".
2. Confirm the selection by pressing the SET button.
3. Select "ZEBRA 2 DETECT", and rotate the rotary pulse
switch to adjust to the required value.
4. Confirm the value by pressing the SET button.
Notice
Note that if the VF ZEBRA switch is not set to "ON",
the zebra 1 and 2 signals will not be displayed.
However, while pressing and holding the VF CHARA
button on the right side of the camera, the zebra
signals are displayed forcibly regardless of these
settings, so that the video level can be checked
temporarily.
5.10.6 ! INDICATOR
(Selecting the warning display items)
! INDICATOR sets up the functions that interact with the
warning display on the VF (! indicator).
1. Select "! INDICATOR" and confirm. The following
submenu screen is displayed.
! INDICATOR
GAIN UP
AWB OFF
VTR SAVE
LENS EXT
MANUAL KNEE
SKIN DTL
SHUTT/SUP-V
A. IRIS CORR
2. Rotate the rotary pulse switch to select an item to be set.
3. Press the SET button, then rotate the rotary pulse switch
to select "ON" or "OFF".
If "ON" is selected for a function, the ! indicator turns on
when the function is activated.
4. Confirm the selection by pressing the SET button.
5. SETTINGS AND ADJUSTMENT OF CAMERA
CURRENT
ON ＊
ON ＊
ON ＊
＊
ON
＊
ON
＊
ON
＊
ON
＊
ON
DNS-33W 0503 VOL1 (E)
5. On the CURRENT column asterisks are displayed next to
the functions currently selected to display the warning.
5.10.7 BARS TITLE/MODE
(Selecting the title displayed on the
color bar and the type of color bar)
BATS TITLE/MODE sets up the title displayed on the color
bar (up to 10 characters) and the position to display the color
bar.
TITLE (Inputting title)
BARS TITLE/MODE
DISPLAY
POSITION
TITLE
BARS MODE
1. Select "BARS TITLE" from the Normal Menu and
confirm.
The screen switches to the submenu screen.
2. Select "TITLE" submenu.
The flashing cursor moves to allow you to enter the title.
3. Select the necessary character using the rotary pulse
switch, and then press the SET button to confirm the
selected character one by one in the parenthesis.
4. When all the characters in the parenthesis are set, the
character input mode ends and the new file name is set.
If the file name is less than 10 characters long, be sure
to input blank spaces in the remaining fields. The title
input mode does not end unless there are 10 characters
confirmed as the file name. Rotating the rotary pulse
switch scrolls through the characters as shown in the
figure below.
Camera Front Side
ON
OFF
SHUTT/SUP-V
AUDIO OUT VTR
Rotating the rotary pulse switch UP/DOWN will scroll
＊
through the characters in the following directions.
represents a blank space.
ABCDEFGHIJKLMN OPQRSTUVWXYZ
5 - 19
OFF
RIGHT
( )
NORMAL
SET Button
AWB
ABB
MENU
Rotary Pulse Switch
U P
!#$...{}" 0123456789
DOWN
DNS-33W