Ikegami Editcam 3 DNS-33W Operation Manual page 99

5.10.14 Structure of Maintenance Menu (2/3)
This section shows the structure of the Maintenance Menu (2/3).
Submenu Detailed Setting Items
CPU SYSTEM CONTROL LEVEL CONTROL
SEMI SELF MODE
SEMI REMOTE MODE
AWB / ABB MODE AWB WITH A.IRIS
AWB WITH CC FILT
SHOCKLESS AWB
FILTER AWB MEM
AWB REFERENCE
REFERENCE SET
AUTO IRIS SET IRIS SET MODE
IRIS LEVEL SET
PEAK RATIO SET
IRIS GAIN (See Notice)
IRIS SPEED (See Notice)
IRIS LIMIT
LENS ADJUST
G.L. PHASE ADJUST SC COARSE
FINE
H PHASE
LENS SELECT FILE
NUMBER
NAME
SET MODE
EXT VTR REC CONTROL CONTROL MODE
REC PRIORITY
26P VIDEO SEL
VIDEO PROCESS MODE CAL PULSE
EFFECT MODE
Notice
The IRIS GAIN and IRIS SPEED settings are not available for the B3 lens and thus not displayed.
5. SETTINGS AND ADJUSTMENT OF CAMERA
Mode Selection Default Value
OPE, OFF OPE
OFF, ON OFF
OFF, ON OFF
OFF, ON ON
OFF, ON OFF
OFF, ON-1.0s, ON-1.0s
ON-1.5s, ON-2.0s
OFF, ON OFF
OFF, ON OFF
AWB, ABB ABB
OFF, ON OFF
-100 to +100 0
-100 to +100 0
1 to 100 50
1 to 100 50
F22, F20, F18, F16 F22
OFF, F2.8, F16 OFF
-100 to +100 0
-100 to +100 0
-100 to +100 0
OFF, ON ON
NO.1 to 8 NO.1
12 characters
OFF, ON OFF
EDGE TRIG, EDGE TRIG
HI LVL REC,
LO LVL REC,
POSI PULSE,
NEGA PULSE
PARARELL, EXT, PARALLEL
VTR, INV VTR
[NTSC] USA :COMP
COMP (WO/SETUP), (W/SETUP)
COMP (W/SETUP), JPN : COMP
COMP (SMPTE), (WO/SETUP)
R/G/B EUR :COMP
[PAL] (EBU N10)
COMP (EBU N10),
R/G/B
OFF, ON OFF
---
OFF, CCD SCAN
REVERSE,
ALT FIELD PROG
DNS-33W 0503 VOL1 (E)
Function
Sets the various level data controlled by the CPU to
"0" (OFF: the central value) temporarily
Turns ON/OFF the semi self mode
Turns ON/OFF the semi remote mode
Turns ON/OFF the mode to shift to auto iris forcibly
while executing AWB
Turns ON/OFF the mode to interact ECC filter to AWB
Turns ON/OFF the shock-less AWB mode and sets
up the operation time
Turns ON/OFF AWB memory for each ECC filter
Turns ON/OFF the function to use the set value for
AWB conclusive value
Creates a normal data to use as the AWB/ABB
conclusive value
Turns ON/OFF the auto iris function
Sets up the iris level
Sets up the peak ratio of auto iris function
Sets up the iris gain
Sets up the iris speed
Sets up the iris limit value for the closing direction
Sets up the fixed iris value control output in case
of lens adjustment
Adjusts coarsely the phase between the external
synchronization signal for GENLOCK and the subcarrier
Adjust finely the phase between the external
synchronization signal for GENLOCK and the subcarrier
Adjusts the phase between internal horizontal
synchronization and the external synchronization
signal for GENLOCK
Turns ON/OFF the lens files
Selects the lens number (NO.1 to NO.8)
Sets up the lens file names
Turns ON/OFF the lens file creation mode
Switches start/stop control for the external VTR
Switches the output destination of start/stop for the
external VTR
Switches the video output from the optional VTR 26
pin connector
Turns ON/OFF the SAW TOOTH calibration pulse
Selects the functions in case the option
D.PROC_SUB BOARD is connected
If the option D.PROC SUB BOARD is not connected,
"--- " is displayed and this menu cannot be selected
5 - 25
DNS-33W