Fieldpak Loading And Changing - Ikegami Editcam 3 DNS-33W Operation Manual

Notice
When the "AWB WITH CC FILT" mode is set to
"ON", the camera automatically measures the color
temperature of the subject and selects the best color
temperature of the ECC filter. In this mode, you can
perform auto white balance in all color temperature
range just by setting the AWB switch without
worrying about the color temperature of the subject.
The "AWB WITH CC FILT" mode is set on the
"AWB WITH CC FILT" of the Maintenance Menu (2/
3). For details of the setting, refer to "5.10.16 AWB/
ABB MODE (Selecting AWB function and setting the
reference data)", " AWB WITH CC FILT (ECC filter
interlocking mode when AWB is activated)".
CAUTION
Hunting may occur when a lens with an automatic
aperture function is used. In this case, adjust the
AUTO IRIS. For details of the setting, refer to "4.5
Adjusting the Lens", " AUTO IRIS Operation" and
"5.10.17 AUTO IRIS SET (Setting the auto iris
operation)".
4.7.2 Auto Black Balance
1. Set the AWB/ABB switch to "ABB".
The lens iris closes automatically, and auto black balance is
activated. The adjustment value is stored in the memory.
2. Upon completion of the auto black balance, "OK" or "NG"
appears on the VF screen. If "NG" appears, the setting
returns to the former status before auto black balance.
Remove the cause and perform the procedure again.
Notice
• The Auto Black Balance (ABB) adjustment is
required only in the following cases:
When the camera is used for the first time
When the difference in the ambient temperature
has changed significantly
When GAIN is changed to +18dB or more
• No adjustment is required in the following cases:
When power is turned off
Adjust only the white balance when the color
temperature of the lighting has changed.
• When the iris is being set manually, it will remain
closed even after the ABB has been adjusted.
Reset the iris before resuming shooting.
• During ABB adjustment, the gain selection circuit
is switched automatically and flicker appears
several times on the VF screen. This is normal
and not indicative of malfunctioning.
• To discontinue ABB adjustment, set the AWB/ABB
switch to "ABB" again. The adjusted setting is
cleared, returning to the former status before auto
black balance.
4.7.3 Auto Black Shading
Following the auto black balance adjustment, black shading
adjustment can be automatically performed.
1. Set the AWB/ABB switch to "ABB" and hold it in this
position.
2. After the lens iris is automatically closed, black set
adjustment starts. At this time, the following display
appears on the VF screen.
3. After completion of black set adjustment, black shading
adjustment starts.
The VF screen display changes to "A.BLK SHADE" as
shown below. At this time, you may release your finger
from the AWB/ABB switch.
4. Upon completion of auto black shading, "OK" or "NG"
appears on the VF screen. If "NG" appears, the setting
returns to the former status before auto black shading.
Notice
To discontinue auto black shading, set the AWB/
ABB switch to "ABB" again. The adjusted setting is
cleared, returning to the former status before auto
black shading.

4.8 FieldPak Loading and Changing

Scenes picked up by the camera are recorded onto the hard
disk in an FP2. The procedures to load (insert) and replace an
FP2 are shown below.
4.8.1 FieldPak Loading
1. Open the FieldPak holder by pressing the EJECT key on
the top of the camera.
2. Place an FP2 in the FieldPak holder.
The FP2 may be oriented in any direction.
DNS-33W 0503 VOL1 (E)
4. OPERATION
ABB
– BLK SET –
A.BLK SHADE
– BLK SHADE –
4 - 7
DNS-33W