Ikegami Editcam 3 DNS-33W Operation Manual page 89

Submenu Detailed Setting Items
LOW/MID/HIGH LOW GAIN
GAIN MODE
MID GAIN
HIGH GAIN
HYPER GAIN
BATT/DISK WARNING WARN FRONT TALLY
WARN BACK TALLY
SCENE FILE SCENE NUMBER
STORE SCENE
LEVEL ADJUST MASTER GAMMA
MASTER PED
DTL GAIN
SKIN DTL MODE
SKIN DTL
COLOR SAT MODE
COLOR SAT
ADJUST CLR
OTHERS RET SOURCE
G.L. INH IN G.L. VIDEO
BARS WITH CAP
PWR ON AWB OFF CLR
RET CH SEL SW
VF G TALLY
MENU CURSOR
5. SETTINGS AND ADJUSTMENT OF CAMERA
Mode Selection Default Value
-3, 0, +3, +6, +9, 0 dB
+12 dB
0, +3, +6, +9, +12, +6 dB
+18 dB
+3, +6, +9, +12, +18, +12 dB
+24 dB
SEL (30-48dB),
SEL (30-42dB)
SEL (30-42dB),
SEL (30-36dB),
+48, +42, +36, +30dB
ON, OFF ON
ON, OFF ON
OFF, NO.1 to 8 OFF
NO.1 to 8, CANCEL READY
-100 to +100 0.0
-100 to +100 0.0
-100 to +100 0.0
ON, OFF OFF
-100 to +100 0.0
ON, OFF OFF
-100 to +100 0.0
PUSH SET -> CLR, READY
CANCEL
VTR VIDEO, VTR VIDEO
GL VIDEO
---, OFF, ON ---
ON, OFF ON
YES, NO YES
RET/VTR, RET+VTR RET/VTR
(Only RET+VTR (RET+VTR for B3 lens)
available for B3 lens)
NO, YES NO
NEXT, STAY NEXT
DNS-33W 0503 VOL1 (E)
Function
Allocates a gain value in the "L" position of the
GAIN SELECT switch
Allocates a gain value in the "M" position of the
GAIN SELECT switch
Allocates a gain value in the "H" position of the
GAIN SELECT switch
Allocates a gain value of the HYPER GAIN switch
Turns the FRONT TALLY warning display ON/OFF
Turns the BACK TALLY warning display ON/OFF
Loads a scene file
Registers the scene file
Adjusts the MASTER GAMMA level
Adjusts the MASTER PED level
Adjusts the DTL GAIN level
Turns the SKIN DTL MODE ON/OFF
Adjusts the SKIN DTL GAIN
Turns the COLOR SAT MOD ON/OFF
Adjusts the COLOR SAT level
Returns the adjusted levels to the default settings
Selects whether to turn the RET video signal into
VTR video or GL VIDEO
Selects whether to use GENLOCK input signal as
the external synchronization signal
ON/OFF can be specified only when "GL VIDEO" is
selected in RET SOURCE described above
Selects whether to make the iris cap interact when
in BAR ON setting
In the power has been turned OFF with a panel with
AWB OFF mode set to "AWB OFF" in the past, this
function turns the AWB OFF mode is connected the
next time.
Can only be specified when a remote control panel
is connected
Sets how the switch RET channel for the VF by
using the RET and VTR buttons on the lens
(The REC button on the handle works the same as
the VTR button on the lens)
RET/VTR : RET button for RET1, VTR for RET2
RET+VTR : Press VTR button while pressing and
holding RET button to switch RET channel
* Only RET+VTR available for B3 lens.
Selects whether or not to mount the VF with G
TALLY lamp
Selects the menu cursor movement when the SET
button is pressed
5 - 15
DNS-33W