Ikegami Editcam 3 DNS-33W Operation Manual page 108

5 - 34 5. SETTINGS AND ADJUSTMENT OF CAMERA
5.10.20 EXT VTR REC CONTROL
Sets up the interface when the dockable VTR is connected to
the 26 pin VTR connector.
EXT VTR REC CONTROL
CONTROL MODE
REC PRIORITY
26P VIDEO SEL
CONTROL MODE
Switches start/stop controlling methods of VTR according to
the external VTR to be used. 5 controlling methods are
available. Select one to fit the specification of the external
VTR.
Setting Value
EDGE TRIG Method to start/stop VTR by the change of control
signal level (Hi Lo).
HI LVL REC Method to start REC when the control signal level
is Hi and to stop VTR when the signal level
changes from Hi to Lo.
LO LVL REC
Method to start REC when the control signal level
is Lo and to stop VTR when the signal level
changes from Lo to Hi.
POSI PULSE Method to start/stop VTR when a positive pulse is
given.
NEGA PULSE Method to start/stop VTR when a negative pulse is
given.
Reference
For details on the start/stop controlling methods of
VTR, refer to the instruction manuals attached to the
external VTR.
Notice
"EDGE TRIG" or "HI LVL REC" (SMPTE method) is
the main start/stop controlling methods of VTR for
broadcasting. When the controlling method is
unknown, try "EDGE TRIG" first.
DNS-33W
HI LVL REC
PALALLEL
COMP (WO/SETUP)
Description
DNS-33W 0503 VOL1 (E)
26P VIDEO SEL
Setting "26P VIDEO SEL" will select the component signal
type output from the 26 pin connector.
Selection Output Signal
COMP Y, Cr, Cb
β CAM level
(WO/SETUP)
[only NTSC] Without setup 7.5%
COMP Y, Cr, Cb
β CAM level
(W/SETUP)
[only NTSC] With setup 7.5%
COMP Y, Cr, Cb SMPTE
(SMPTE) /EBU N10 level
[NTSC]
(EBU N10)
[PAL]
R/G/B R, G, B
Notice
When R/G/B is selected, whether to put SYNC to
Gch or not can be set up with the RGB SYNC
switch above the sub board (26P I/F) on
DRIVE&PULSE module (second from the front,
printed "2" on the tab) inside the camera.
26P I/F Module
ON OFF
ON: with SYNC
OFF: no SYNC
REC PRIORITY
Switches the priority to output FP2 control by the REC
button on the camera, the VTR button on the lens, or the
FIELDPAK switch on the camera and the TALLY lamp
(FRONT TALLY, REAR TALLY, BACK TALLY, and upper
and lower TALLY in the VF) control to the recorder section
of the camera or external VTR. This setting is valid only
when the external VTR is connected.
Signal Level
Y;V:0.714Vp-p
/ S:0.286Vp-p Setup:0%
Cr;0.756Vp-p (75% BAR)
Cb;0.756Vp-p (75% BAR)
Y;V:0.714Vp-p
/ S:0.286Vp-p Setup:7.5%
Cr;0.7Vp-p (75% BAR)
Cb;0.7Vp-p (75% BAR)
Y;V:0.7Vp-p / S:0.3Vp-p Setup:0%
Cr;0.525Vp-p (75% BAR)
Cb;0.525Vp-p (75% BAR)
RGB;0.7Vp-p Setup:0%
G on Sync 0.3Vp-p
or No Sync switch
DRIVE&PULSE Module