Ikegami Editcam 3 DNS-33W Operation Manual page 102

5 - 28 5. SETTINGS AND ADJUSTMENT OF CAMERA
5.10.15 CPU SYSTEM CONTROL (Selecting
operation mode of the Camera)
Sets up various operation modes. Set up the mode according
to the expected operation conditions.
CPU SYSTEM CONTROL
LEVEL CONTROL
SEMI SELF MODE
SEMI REMOTE MODE
LEVEL CONTROL
If the LEVEL CONTROL is turned OFF, the level data
controlled from the CPU are temporarily changed to "0" (the
central value) (the memory off function). This is used when
confirming the adjustment status of each module, or finding
out the cause of failure by abnormal data from the CPU.
When in operation, ensure that this setting is "OPE". When
this submenu is set to "OFF", the level cannot be controlled
from the remote controllers.
This setting is valid only while the power is turned ON. If
the power is turned OFF, this setting is reset to "OPE".
SEMI SELF MODE
If the "SEMI SELF MODE" is turned "ON", the adjustment
data set from the remote controller can be loaded. For
example, when detaching the remote controller and operating
by the camera alone after adjusting the camera using the
remote controller, turning this function "ON" will enable the
camera to keep the ON/OFF and the adjustment settings set
by the remote controller.
Turning the SEMI SELF MODE "OFF" will return to the
normal level setting, however turning this function "ON"
again will load the adjustment data by the remote controller
any time.
SEMI REMOTE MODE
When the SEMI REMOTE MODE is turned "ON", the
control priority of the ON/OFF settings of the following
switches on the right and front of the camera can be returned
to the camera in remote operation (when controlling from the
remote controllers, etc.). Then, turning ON/OFF a function
from the remote controller is disabled.
When the SEMI REMOTE MODE is "OFF", the control
priority of these switches is switched to the remote controller,
and turning ON/OFF a function from the camera is disabled.
• GAIN SELECT switch
• AWB SELECT switch (OFF, A, B)
• OUTPUT SELECT switch
• SHUTT/SUP-V switch
DNS-33W
OPE
OFF
OFF
DNS-33W 0503 VOL1 (E)
5.10.16 AWB/ABB MODE (Selecting AWB
function and setting the reference data)
AWB/ABB MODE selects the operation mode for AWB.
This menu creates the reference file for AWB and ABB.
AWB / ABB MODE
AWB WITH A. IRIS
AWB WITH CC FLT
SHOCKLESS AWB
FILTER AWB MEM
AWB REFERENCE
REFERENCE SET
AWB WITH A.IRIS
(Auto iris mode when AWB is activated)
Changes the iris mode to auto iris mode when AWB is
activated.
When set to "ON", the camera changes to auto iris mode
when AWB is activated.
When set to "OFF", the camera remains in the current iris
mode.
AWB WITH CC FILT
(ECC filter interlocking mode when AWB is
activated)
When set to "ON", measures the color temperature of the
subject and interlock the ECC filter if required. AWB can be
activated in all color temperature range by the AWB,
disregarding the color temperature of the subject.
SHOCKLESS AWB
(Setting the switching time of AWB memory)
Sets up the duration of time to switch the AWB memory.
The AWB memory data will be gradually switched in the set
time; therefore, the shock will be minimized.
Setting Value
OFF The memory data will be switched at once
ON-0.3s The memory data will be gradually switched in 0.3 seconds
ON-0.5s The memory data will be gradually switched in 0.5 seconds
ON-1.0s The memory data will be gradually switched in 1.0 seconds
ON-1.5s The memory data will be gradually switched in 1.5 seconds
ON-2.0s The memory data will be gradually switched in 2.0 seconds
Notice
When AWB WITH CC FILT is set to "ON", the
SHOCKLESS AWB function cannot be used. When
AWB WITH CC FILT setting is changed to "ON", the
SHOCKLESS AWB function setting will automatically
change to "OFF".
ON
OFF
ON-1.0s
OFF
OFF
ABB
Description