Carrier Weathermaster 48P030-100 Controls, Start-Up, Operation, Service, And Troubleshooting page 190

ITEM
GEN.I GENERAL INPUTS
FLT.S
Filter Status Input
G.FAN
Fan Request From IGC
REMT
Remote Input State
ENTH
Enth. Switch Read High?
S.FN.S
Supply Fan Status Switch
FRZ.S
Freeze Status Switch
PP.SW
Plenum Press.Safety Sw.
DL.S1
Demand Limit Switch 1
DL.S2
Demand Limit Switch 2
DH.IN
Dehumidify Switch Input
FD.BK COMPRESSOR FEEDBACK
HPS.A
Circ A High Press. Switch
HPS.B
Circ B High Press. Switch
CS.A1
Compressor A1 Feedback
CS.A2
Compressor A2 Feedback
CS.A3
Compressor A3 Feedback
CS.B1
Compressor B1 Feedback
CS.B2
Compressor B2 Feedback
CS.B3
Compressor B3 Feedback
STAT THERMOSTAT INPUTS
G
Thermostat G Input
W1
Thermostat W1 Input
W2
Thermostat W2 Input
Y1
Thermostat Y1 Input
Y2
Thermostat Y2 Input
FIRE FIRE-SMOKE INPUTS
FSD
Fire Shutdown Input
PRES
Pressurization Input
EVAC
Evacuation Input
PURG
Smoke Purge Input
REL.H RELATIVE HUMIDITY
OA.RH
Outside Air Rel. Humidity
OA.EN
Outdoor Air Enthalpy
OA.DP
Outside Air Dewpoint Temp
RA.RH
Return Air Rel. Humidity
RA.EN
Return Air Enthalpy
SP.RH
Space Relative Humidity
SP.EN
Space Enthalpy
AIR.Q AIR QUALITY SENSORS
IAQ.I
IAQ - Discrete Input
IAQ
IAQ - PPM Return CO2
OAQ
OAQ - PPM Return CO2
DAQ
Diff.Air Quality in PPM
IQ.P.O
IAQ Min.Pos. Override
CFM CFM SENSORS
O.CFM
Outside Air CFM
R.CFM
Return Air CFM
S.CFM
Supply Air CFM
D.CFM
Fan Track Control D.CFM
RSET RESET INPUTS
SA.S.R
Supply Air Setpnt. Reset
SP.RS
Static Pressure Reset
4-20 4-20 MILLIAMP INPUTS
IAQ.M
IAQ Milliamps
OAQ.M
OAQ Milliamps
SP.R.M
SP Reset milliamps
DML.M
4-20 ma Demand Signal
EDR.M
EDT Reset Milliamps
ORH.M
OARH Milliamps
SRH.M
SPRH Milliamps
RRH.M
RARH Milliamps
SAC.M
SACFM Milliamps
SA.M.T
Supply Air CFM Trim (ma)
RAC.M
RACFM Milliamps
RA.M.T
Return Air CFM Trim (ma)
OAC.M
OACFM Milliamps
OA.M.T
Outside Air CFM Trim(ma)
BP.M
BP Milliamps
BP.M.T
Bldg. Pressure Trim (ma)
SP.M
SP Milliamps
SP.M.T
Static Press. Trim (ma)
NOTE(S):
a. The display text changes depending on the remote switch configuration (Configuration
will be "On" or "Off." If RM.CF is set to 1 (Occupied/Unoccupied Switch), then the display text will be "Occupied" or "Unoccupied." If RM.CF is set to 2 (Start/Stop), then
the display text will be "Stop" or "Start." If RM.CF is set to 3 (Override Switch), then the display text will be "No Override" or "Override."
APPENDIX A — LOCAL DISPLAY TABLES (CONT)
Table F — MODE — INPUTS
EXPANSION
DRTY/CLN
ON/OFF
a
YES/NO
ON/OFF
ALRM/NORM
HIGH/LOW
ON/OFF
ON/OFF
ON/OFF
HIGH/LOW
HIGH/LOW
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ALRM/NORM
ALRM/NORM
ALRM/NORM
ALRM/NORM
HIGH/LOW
–2.0 to 2.0
–2.0 to 2.0
–2.0 to 2.0
–2.0 to 2.0
–2.0 to 2.0
RANGE UNITS
FLTS
IGCFAN
RMTIN
ENTH
SFS
FRZ
PPS
DMD_SW1
DMD_SW2
DHDISCIN
CIRCAHPS
CIRCBHPS
CSB_A1
CSB_A2
CSB_A3
CSB_B1
CSB_B2
CSB_B3
G
W1
W2
Y1
Y2
FSD
PRES
EVAC
PURG
% OARH
OAE
dF OADEWTMP
% RARH
RAE
% SPRH
SPE
IAQIN
IAQ
OAQ
DAQ
% IAQMINOV
CFM OACFM
CFM RACFM
CFM SACFM
CFM DELTACFM
^F SASPRSET
SPRESET
ma IAQ_MA
ma OAQ_MA
ma SPRST_MA
ma DMDLMTMA
ma EDTRESMA
ma OARH_MA
ma SPRH_MA
ma RARH_MA
ma SACFM_MA
SAMATRIM
ma RACFM_MA
RAMATRIM
ma OACFM_MA
OAMATRIM
ma BP_MA
BPMATRIM
ma SP_MA
SPMATRIM
 
UNIT RM.CF). If RM.CF is set to 0 (No Remote Switch), then the display text
190
CCN POINT WRITE STATUS
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
forcible
config
config
config
config