MCi Crusader II 1989 Maintenance Manual page 450

Date
1-1-89
Page __
13_-4_7 _ _
MC-9 MAINTENANCE MANUAL
SPEED TRANSMISSION SPECIFICATIONS: STANDARD AND OPTIONAL
Manufacturer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ........................................... Fuller T-11605D. 11605F
Speeds ................................................................................................ 5-Forward
1-Reverse
Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ............................................................. On Engine
Gear Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .................. Remote Control
Oil Capacity ............................................................................... 22 U.S. Pints (10.41 liters)
T-11605O T-11605F
GEAR RATIOS
(Standard) {Optional)
1st .......................................... : .......... , ......................... ; ................ 5.46 ...... 7.20
2nd ............................................................................................... 3.23 .••... 3.90
3rd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................................ 2.05 ...... 2.12
4th .......................................................................................•........ 1.31 ...... 1.46
5th ..............................................
~
.............................................•... 1.00 ...... 1.00
Reverse ................... ., ..•.................................................................... 5.57 ...... 5.57
AXIAL CLEARANCE FOR MAIN SHAFT GEARS
Axial Clearance (End Play) limits are:
Reverse speed gear - minimum of .005" (.127 mm)
Forward speed gears - .005" -.012" (.127 -.305 mm)
Washers are. used to obtain the correct limits and are available in the following thicknesses:
LIMITS
COLOR CODE
.248" -.250" (.630-.635 mm) ................................................................................•. ·. White
.253" -.255" (.642-.647 mm) ................................................................................... Green
.258" -.260" (.655-.660 mm) .............................................................................•.... Orange
.263" -.265" (.668-.673 mm) ...................................•................................. · .............. Purple
.268" -.270" (.680-.685 mm) ................................................................................•. Yellow
.273" -.275'" (.693-.698 mm). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ................................ : .. Black
Refer to Parts Manual for washer part numbers
Always use the .248"-.250" (.630-.635 mm) low limit washer (White) ,n the 1st and 3rd speed gear positions.
TORQUE SPECIFICATIONS
NUTS
Clutch Housing to Case .......................................................... 180-190 ft. lbs. (244-257 Nm)
Drive Gear Bearing Nut ...............•...........•............................... 250-300 ft. lbs. (339-407 Nm)
Output Shaft Front Bearing Nut ............................•...................•... 250-300 ft. lbs. (339-407 Nm)
Companion Flange Nut ........•.................................................. 400-500 ft. lbs. (542-678 Nm)
CAP SCREWS*
Clutch Housing to Case ..•....•.............•..............................•...... 90-100 ft. lbs. (131-136 Nm)
Countershaft Front Bearing Retainer ........•..........................•........•..•..•. 20-25 ft. lbs. (27-34 Nm)
Output Shaft Key Spacer Ring ............•....................•....................... 20-25 ft. lbs. (27-34 Nm)
Output Shaft Key ............•......•................................................ 20-25 ft. lbs. (27-34 Nm)
Front Bearing Cover ........•............................•........................... 35-45 ft. lbs. (47-61 Nm)
Shiftbar Housing ...................................................•......•......... 35-45 ft. lbs. (47-61 Nm)
Mamshaft Rear Bearing Cover ................................................. : ....... 35-45 ft. lbs. (47-61 Nm)
Countershaft Rear Bearing Covers ..................................................•... 35-45 ft. lbs. (47-61 Nm)
Reverse Idler Shaft Lock ......................
7 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
25-35 ft. lbs. (34-47 Nm)
*
Do not torque .capscrews dry