Komatsu D85EX-18 Operation & Maintenance Manual page 386

Hydraulic tank - Replace oil / Hydraulic oil filter ele-
ment - Replace / Hydraulic tank strainer - Clean..
.......................................................................4-62
Hydraulic tank breather - Clean............................ 4-31
Hydraulic tank breather element - Replace...........4-59
Idler - Adjust clearance......................................... 4-24
Idler - Adjust clearance horizontally...................... 4-24
Idler - Adjust clearance vertically.......................... 4-25
Idler - Check oil level.............................................4-23
If any problem is found..........................................2-11
If machine monitor shows warning display......... 3-234
Indicator - Check electrolyte level......................... 4-46
Initial 250 hours maintenance (only 1st maintenance
of new machine)............................................ 4-15
Inside operator's compartment..............................2-11
Inspecting machine............................................... 2-10
Introduction............................................................. 1-7
Jobsite - Investigate/confirm conditions................ 2-17
Joystick (steering, directional and gear shift lever)
(PCCS lever)..................................................3-92
Joystick (steering, directional and gear shift lever)
(PCCS lever) - Adjust.................................. 3-152
Jumper cable - Connect......................................3-229
Jumper cable - Disconnect................................. 3-230
KCCV filter element - Replace.............................. 4-67
KDPF - Clean........................................................4-75
KDPF soot accumulation caution lamp................. 3-23
KDPF system caution lamp...................................3-22
Keep machine clean............................................. 2-10
Komatsu Closed Crankcase Ventilation (KCCV).3-113
Komatsu Diesel Particulate Fillter (KDPF) - Handle.....
.....................................................................3-103
Komatsu genuine lubricants....................................4-2
Komatsu genuine replacement parts...................... 4-2
KOMTRAX.......................................................... 3-128
L.H. armrest - Adjust........................................... 3-153
Lamp - Check operation......................................3-143
Language settings.................................................3-77
Leveling work...................................................... 3-182
Lift cylinder support shaft - Lubricate.................... 4-40
Lifting of personnel prohibited...............................2-14
Link pitch - Measure............................................3-187
Loading and unloading with trailer...................... 3-215
Location of EPA regulations, engine serial No. plate...
.......................................................................1-10
Location of product identification number (PIN) / ma-
chine product identification number............... 1-10
8-4
I
J
K
L
Location of safety labels......................................... 2-5
Lock.................................................................... 3-191
Lock inspection cover............................................. 4-3
Low register range (bass) - Adjust...................... 3-214
Lubricating points on fixed multi-shank ripper spec
machines....................................................... 4-41
Lubricating points on variable multi-shank ripper spec
machines....................................................... 4-41
Lubrication chart..................................................... 7-6
Lumber support - Adjust........................... 3-147,3-150
Machine - Adjust dozing angle............................3-184
Machine - Check walk-around............................ 3-131
Machine - Clean with compressed air...................4-30
Machine - Lift...................................................... 3-218
Machine - Load................................................... 3-215
Machine - Lubricate.............................................. 4-39
Machine - Operate.............................................. 3-186
Machine - Operate with cold air to face and warm air
to feet...........................................................3-205
Machine - Park....................................................3-189
Machine - Pushing work......................................3-183
Machine - Running-in the new machine..............3-163
Machine - Secure................................................3-216
Machine - Shift gear............................................3-170
Machine - Shift gear in preset mode................... 3-173
Machine - Start....................................................3-168
Machine - Start (Travel forward and reverse) / Stop....
.....................................................................3-168
Machine - Start after long-term storage.............. 3-223
Machine - Steer...................................................3-176
Machine - Stop....................................................3-170
Machine - Switch travel direction........................ 3-175
Machine - Transport............................................ 3-215
Machine - Travel on load.....................................3-215
Machine - Turn during forward travel.................. 3-177
Machine - Turn gradually during forward travel on
downhill slope.............................................. 3-178
Machine - Turn normally..................................... 3-176
Machine - Turn on downhill slope....................... 3-178
Machine - Unload................................................3-217
Machine equipment name.......................................3-2
Machine monitor - Check.................................... 3-144
Machine monitor - Operate when operator identifica-
tion function is available with skip..................3-78
Machine monitor - Operate when operator identifica-
tion function is available without skip.............3-79
Machine monitor - Operate when starting engine in
abnormal situation..........................................3-11
Machine monitor - Operate when starting engine in
normal situation............................................... 3-7
Machine monitor - Operate when starting engine
while engine shutdown secondary switch is ON...
.........................................................................3-8
Machine monitor - Operate when starting switch is
ON while operator ID input is set................... 3-10
INDEX
M