Page 1 Panel PC 2100 Built-in devices User's manual Version: 1.17 (June 2018) Model no.: MAPPC2100-ENG Translation of the original manual All values in this manual are current as of its publication. We reserve the right to change the contents of this manual without notice.
Page 2 Commercial register number: FN 111651 v. The place of fulfillment in accordance with article 5 of the European Convention on Courts of Jurisdiction and Enforcement is A-5142 Eggelsberg, Austria Austrian DVR no.: 0721301 VATIN: ATU62367156 Panel PC 2100 user's manual V1.17...
Page 3 Chapter index 1: General information 2: Technical data 3: Commissioning 4: Software 5: Standards and certifications 6: Accessories 7: Servicing and maintenance Appendix A Panel PC 2100 user's manual V1.17...
Page 4: Table Of Contents
2.2.4 Device interfaces and slots........................48 2.2.4.1 Device interfaces - Overview......................48 2.2.4.2 +24 VDC power supply........................49 2.2.4.3 Ethernet 1 interface (ETH1).......................51 2.2.4.4 Ethernet 2 interface (ETH2).......................51 2.2.4.5 USB interfaces........................... 52 2.2.4.6 CFast slot............................54 2.2.4.7 Power button............................54 Panel PC 2100 user's manual V1.17...
Page 5 2.3.4.2 Basic information..........................147 2.3.4.3 5CFAST.xxxx-00..........................149 2.3.4.4 5CFAST.xxxx-10..........................152 2.3.5 Interface options............................ 158 2.3.5.1 5ACCIF01.FPCC-000........................158 2.3.5.2 5ACCIF01.FPCS-000........................166 2.3.5.3 5ACCIF01.FPLK-000........................173 2.3.5.4 5ACCIF01.FPLS-000........................178 2.3.5.5 5ACCIF01.FPLS-001........................183 2.3.5.6 5ACCIF01.FPSC-000........................188 2.3.5.7 5ACCIF01.FPSC-001........................194 2.3.5.8 5ACCIF01.FSS0-000........................201 2.3.5.9 5ACCIF01.ICAN-000........................206 Panel PC 2100 user's manual V1.17...
Page 6 4.1.5.1 System information.......................... 237 4.1.6 Advanced............................... 238 4.1.6.1 OEM features........................... 239 4.1.6.2 CPU configuration..........................251 4.1.6.3 Graphics (IGD) configuration......................253 4.1.6.4 LAN..............................255 4.1.6.5 PCI express configuration........................257 4.1.6.6 USB configuration..........................259 4.1.6.7 SATA configuration.......................... 260 Panel PC 2100 user's manual V1.17...
Page 7 4.2.1 BIOS upgrade............................271 4.2.1.1 Important information........................271 4.2.1.2 Procedure in EFI shell........................272 4.2.2 Upgrading the firmware on the Panel PC 2100..................273 4.2.2.1 Procedure in Windows (B&R Control Center)................. 273 4.2.2.2 Procedure in EFI shell........................273 4.3 Multi-touch drivers............................274 4.4 Windows 10 IoT Enterprise 2016 LTSB.....................
Page 8 5 Standards and certifications................303 5.1 Standards and guidelines........................... 303 5.1.1 CE marking............................303 5.1.2 EMC directive............................303 5.2 Certifications..............................304 5.2.1 UL certification............................304 5.2.2 GOST-R..............................304 5.2.3 EAC................................304 5.2.4 KC................................305 5.2.5 RCM...............................305 5.2.6 DNV GL certification..........................305 Panel PC 2100 user's manual V1.17...
Page 9 5.2.7.1 General safety guidelines........................ 306 5.2.7.2 Mounting and installation......................... 306 5.2.7.3 Operation............................307 5.2.7.4 Maintenance, breakdowns and disassembly................... 307 5.2.7.5 USB connection with the Panel PC 2100..................308 5.2.7.6 USB connection with the Automation Panel 1000................310 5.2.7.7 USB connection with the 4-port hub....................312 6 Accessories......................314 6.1 Power supply connectors..........................314...
Page 10 A.5.2 3M touch screen (multi-touch generation 2)..................336 A.5.2.1 General information......................... 336 A.5.2.2 Technical data..........................336 A.5.2.3 Temperature/Humidity diagram....................... 336 A.5.3 3M touch screen (multi-touch generation 3)..................337 A.5.3.1 General information......................... 337 A.5.3.2 Technical data..........................337 A.5.3.3 Temperature/Humidity diagram....................... 338 Panel PC 2100 user's manual V1.17...
Page 11: General Information
Revised section "Temperature specifications" on page • Updated section "Known problems / Issues" on page 233. • Harmonized RAM specifications in the technical data for "Interface options" on page 158. Table 1: Manual history Panel PC 2100 user's manual V1.17...
Page 12 "Windows 10 IoT Enterprise 2016 LTSB" on page 275 ° "B&R Hypervisor" on page 290 ° "mapp Technology" on page 291 1.17 2018-06-22 Updated section "Network stack" on page 256. Table 1: Manual history Panel PC 2100 user's manual V1.17...
Page 13: Safety Guidelines
Electronic devices are never completely failsafe. If the programmable logic controller, operating/monitoring device or uninterruptible power supply fails, the user is responsible for ensuring that other connected devices such as motors are brought to a safe state. Panel PC 2100 user's manual V1.17...
Page 14: Transport And Storage
Automation Panel and Power Panel are protected on the front against the ingress of dust or moisture when installed properly (e.g. cutout installation). The back of all devices must be protected from the ingress of dust and moisture, however; any collected dust must be removed at suitable intervals. Panel PC 2100 user's manual V1.17...
Page 15: Viruses And Dangerous Programs
Therefore, make sure that your administrator accounts are adequately secured to prevent unauthorized changes. Use secure passwords and a standard user account for regular operation. Further measures such as the use of security guidelines are to be applied as needed. Panel PC 2100 user's manual V1.17...
Page 16: Organization Of Notices
Up to 6 mm ±0.1 mm 6 to 30 mm ±0.2 mm 30 to 120 mm ±0.3 mm 120 to 400 mm ±0.5 mm 400 to 1000 mm ±0.8 mm Table 5: Range of nominal sizes Panel PC 2100 user's manual V1.17...
Page 17: Overview
- Landscape format - For PPC900/PPC2100/PPC3100/PPC2200 - For link modules 5AP1130.185C-000 Automation Panel 18.5" Full HD TFT - 1920 x 1080 pixels (16:9) - Multi-touch (projected capacitive) - Control cabinet installation - Landscape format - For PPC900/PPC2100/PPC3100/PPC2200 - For link modules Panel PC 2100 user's manual V1.17...
Page 18 Windows Embedded 8.1 Industry Pro - 64-bit - Multilingual - For PPC2100 - License Windows Embedded Standard 7 5SWWI7.1543-ENG Windows Embedded Standard 7 SP1 - 32-bit - Service Pack 1 - English - PPC2100 - License (without Recovery DVD) - Only available with a new device Panel PC 2100 user's manual V1.17...
Page 19 Recovery DVD) - Only available with a new device 5SWWI7.1843-MUL Windows Embedded Standard 7 Premium SP1 - 64-bit - Service Pack 1 - English - PPC2100 - License (without Recovery DVD) - Only available with a new device Panel PC 2100 user's manual V1.17...
Page 20: Technical Data
The panels can only be operated as a complete system in combination with a link module (Automation Panel 9x3) or CPU board and system unit (Panel PC 900, Panel PC 2100, Panel PC 2200 Panel PC 3100). The panels are installed using retaining clips.
Page 21: System Units
PPC2100 devices in addition to interface option and CFast card connections. Main memory is permanently built into the system unit and cannot be replaced. If a system unit is installed on a panel, the result is an operational Panel PC 2100. Panel PC 2100 systems are mounted using retaining clips.
Page 22 5SWW10.0543-MUL 5SWWI8.0443-MUL B&R Linux 9 (GNU/Linux) 5SWLIN. 0743 -MUL 1) Certain limitations must be taken into account during operation/installation. For additional information, see "chapter 6 - Accessories", section "USB hub". Figure 1: PPC2100 configuration Panel PC 2100 user's manual V1.17...
Page 23: Complete System
Technical data 2.2 Complete system 2.2.1 Mechanical properties 2.2.1.1 Dimensions AP9x3 panels - Dimensions Figure 2: Panel PC 2100 with AP9x3 panels (sample figure) - Dimensions All dimensions are specified in mm. Display type Model number 12.1" single-touch 5AP923.1215-00 13.5 13.5...
Page 24 Technical data AP1000 panels with retaining clips - Dimensions Figure 3: Panel PC 2100 with AP1000 panels with retaining clips (sample figure) - Dimensions All dimensions are specified in mm. Display type Model number 5.7" single-touch 5AP1120.0573-000 19.5 5.7" with keys 5AP1151.0573-000...
Page 25 Technical data AP1000 panels with clamping blocks - Dimensions Figure 4: Panel PC 2100 with AP1000 panels with clamping blocks (sample figure) - Dimensions All dimensions are specified in mm. Display type Model number 10.4" single-touch with keys 5AP1181.1043-000 70.5 21.3...
Page 26: Installation Diagrams
Technical data 2.2.1.2 Installation diagrams Information: When installing the Panel PC 2100, be sure to leave sufficient space for air circulation as well as addi- tional space for operation and maintenance of the device. AP9x3 panels - Installation diagrams Figure 5: Panel PC 2100 with AP9x3 panels (sample figure) - Installation diagram All dimensions are specified in mm.
Page 27 Technical data AP1000 panels with retaining clips - Installation diagrams Figure 6: Panel PC 2100 with AP1000 panels with retaining clips (sample figure) - Installation diagram All dimensions are specified in mm. The cutout tolerances are +0 mm / -0.5 mm.
Page 28 Technical data AP1000 panels with clamping blocks - Installation diagrams Figure 7: Panel PC 2100 with AP1000 panels with clamping blocks (example figure) - Installation diagram All dimensions are specified in mm. The cutout tolerances are +0 mm / -0.5 mm.
Page 29: Spacing For Air Circulation
The air intake and outlet are indicated in the following image. The air intake is located on the bottom to accommo- date the rising warm air. Rear view Side view Figure 8: Panel PC 2100 - Spacing for air circulation S1: ≥ 20 mm S2: ≥50 mm S3: ≥100 mm S4: ≥50 mm...
Page 30: Mounting Orientations
Technical data 2.2.1.4 Mounting orientations The following diagrams show the specified mounting orientations of Panel PC 2100 devices. A PPC2100 is only permitted to be installed as illustrated and described below. 0° 0° Figure 9: Panel PC 2100 - Mounting orientation...
Page 31: Weight Specifications
Table 17: AP1000 panels - Weight Component Model number Weight System unit 5PPC2100.BYxx-000 5CFAST.xxxx-00 CFast cards 5CFAST.xxxx-10 5ACCIF01.FPCC-000 5ACCIF01.FPCS-000 5ACCIF01.FPLK-000 5ACCIF01.FPLS-000 Interface options 5ACCIF01.FPLS-001 5ACCIF01.FPSC-000 5ACCIF01.FPSC-001 5ACCIF01.FSS0-000 5ACCIF01.ICAN-000 Table 18: System units, CFast cards, interface options - Weight Panel PC 2100 user's manual V1.17...
Page 32: Environmental Characteristics
• Thermal Analysis Tool (TAT V4.3.4.13.01) from Intel for simulating a 100% processor load • BurnInTest tool (BurnInTest V7.0 Pro from PassMark Software) for simulating a 100% load on the interface using loopback adapters (USB interfaces) • Maximum system expansion and power consumption Panel PC 2100 user's manual V1.17...
Page 33 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 5ACCIF01.FPSC-001 ✓ ✓ ✓ ✓ ✓ ✓ 5ACCIF01.FSS0-000 5ACCIF01.ICAN-000 ✓ ✓ ✓ ✓ ✓ ✓ Table 19: Maximum ambient temperature for worst-case operation Panel PC 2100 user's manual V1.17...
Page 34 ✓ ✓ ✓ ✓ ✓ 5ACCIF01.FPSC-001 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 5ACCIF01.FSS0-000 ✓ ✓ ✓ ✓ ✓ ✓ 5ACCIF01.ICAN-000 Table 20: Minimum ambient temperature for worst-case operation Panel PC 2100 user's manual V1.17...
Page 35 ✓ ✓ ✓ ✓ ✓ 5ACCIF01.FPSC-001 ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ ✓ 5ACCIF01.FSS0-000 ✓ ✓ ✓ ✓ ✓ ✓ 5ACCIF01.ICAN-000 Table 21: Maximum ambient temperature for typical operation Panel PC 2100 user's manual V1.17...
Page 36 3. If additional interface options and CFast cards are installed, these components can change the temperature limits of the PPC2100 system. 4. Limitations are possible due to the mounting orientation of the Panel PC 2100. For more information, see section "Mounting orientations"...
Page 37 -20 to 60°C -20 to 60°C 5ACCIF01.FSS0-000 -20 to 60°C -20 to 60°C 5ACCIF01.ICAN-000 -20 to 60°C -20 to 60°C Table 24: System units, CFast cards, interface options - Ambient temperature during storage and transport Panel PC 2100 user's manual V1.17...
Page 38 Sensors monitor temperature values at various locations in the PPC2100 device. The location of these temperature sensors is illustrated in Fig. 10 "Panel PC 2100 - Temperature sensor positions" on page 39. The values listed Tab. 25 "Temperature sensor locations" on page 39 represent the defined maximum temperature for this measurement point.
Page 39 Technical data 2.2.2.1.7 Temperature sensor positions Figure 10: Panel PC 2100 - Temperature sensor positions ADI sensors Position Measurement Measurement Max. specified point for Panel Display Temperature of the display (sensor integrated in panel). 5AP923.1215-00: 90°C 5AP923.1505-00: 90°C 5AP923.1906-00 ≤ D0: 75°C 5AP923.1906-00 ≥...
Page 40: Humidity
Table 28: System units, IF options, CFast cards - Humidity The specifications listed correspond to the relative humidity (non-condensing) at an ambient temperature of 30°C. For more detailed information about specific temperature-dependent humidity values, see the technical data for the individual components. Panel PC 2100 user's manual V1.17...
Page 41: Vibration
This value applies to a device in its original packaging. 2.2.2.5 Protection The Panel PC 2100 has IP65 protection on the front and IP20 protection on the back per EN 60529 under the following conditions: • The Panel PC 2100 is installed correctly (see "Installation"...
Page 42: Electrical Characteristics
24 VDC ±25%, SELV Nominal current 3.5 A Inrush current Typ. 6 A; max. 10 A for <300 μs Overvoltage category per EN 61131-2 Electrical isolation Uninterruptible power supply EN 60950 requirements must be observed. Panel PC 2100 user's manual V1.17...
Page 43: Power Calculation
Technical data 2.2.3.2 Power calculation In order to calculate the total power of the Panel PC 2100 device, the power rating of the display being used (see AP9x3 panels - Power calculation AP1000 panels - Power calculation) must be added to the power ratings of the system unit being used, any connected interface options and an optional CFast card.
Page 44 Table 36: CFast cards - Power calculation Example 12" panel 5AP923.1215-00 4.2 W + 7.2 W = 11.4 W 5PPC2100.BY11-000 system unit 23 W (with USB consumers) 23 W CFast card 5CFAST.064G-10 ≥ E0 1.1 W Total max.: 35.5 W Panel PC 2100 user's manual V1.17...
Page 45: Block Diagrams
Female connector, Isolator CAN1 10-pin CAN2 nvSRAM Isolator Terminating L1 LED L2 LED L3 LED Yellow Green Green/Red resistor Figure 12: IF option POWERLINK / 2x CAN / X2X / nvSRAM (5ACCIF01.FPCC-000) - Block diagram Panel PC 2100 user's manual V1.17...
Page 46 Figure 15: IF option POWERLINK/RS232/FRAM (5ACCIF01.FPLS-000) - Block diagram POWERLINK/RS232/nvSRAM IF option POWERLINK/RS232/nvSRAM PCIe 1 FPGA POWERLINK Power down Female connector, nvSRAM RS232 10-pin F_I0 L2 LED L3 LED Green Green/Red Figure 16: IF option POWERLINK/RS232/nvSRAM (5ACCIF01.FPLS-001) - Block diagram Panel PC 2100 user's manual V1.17...
Page 47 IF option 2x RS422/RS485 PCIe 1 RS422/RS485 Power down Female connector, Isolator 10-pin Isolator RS422/RS485 F_IO Terminating L2 LED Terminating L3 LED Yellow Yellow resistor resistor Figure 20: IF option 2x RS422/RS485 (5ACCIF01.FSS0-000) - Block diagram Panel PC 2100 user's manual V1.17...
Page 48: Device Interfaces And Slots
Technical data 2.2.4 Device interfaces and slots 2.2.4.1 Device interfaces - Overview Interfaces are located on the bottom of the Panel PC 2100. (14) (10) (11) (12) (13) (13) Figure 21: Device interfaces - Overview (sample screenshot) No. Type of interface No.
Page 49: Vdc Power Supply
The largest possible wire cross section should be selected (at least 2.5 mm²). Panel PC systems have a ground connection on the interface cover. Grounding Panel PC 2100 user's manual V1.17...
Page 50 The ground connection must be used, for example, to fasten a copper strip to a central grounding point in the control cabinet or system where the device is installed. The largest possible wire cross section should be selected (at least 2.5 mm²). Panel PC 2100 user's manual V1.17...
Page 51: Ethernet 1 Interface (Eth1)
A special driver is required to operate the Ethernet controller. Drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). Information: Only download necessary drivers from the B&R website, not from vendor websites. Panel PC 2100 user's manual V1.17...
Page 52: Usb Interfaces
The USB interface is protected by a maintenance-free "USB current-limiting switch" (max. 1 A). With revisions <B0 for the system units, the max. cable length has been specified at 3 m. Panel PC 2100 user's manual V1.17...
Page 53 USB 2.0 interface on the front. For more information, see section "USB interface" on page USB hub interfaces 4-port USB hub 5ACCUSB4.0000-000 provides up to 4 additional USB interfaces for the Panel PC 2100. For more information, see section "USB hub" on page 322.
Page 54: Cfast Slot
Pushing the reset button triggers a hardware and PCI reset. The Panel PC is restarted (cold restart - possible data loss!). Pressing the reset button does not reset the MTCX processor. Reset button Table 44: Reset button Warning! Resetting the system can result in data loss! Panel PC 2100 user's manual V1.17...
Page 55: Led Status Indicators
Application in service mode This is controlled by Automation Runtime (ARemb and ARwin). Orange Blinking A license violation exists. This is controlled by Automation Runtime (ARemb and ARwin). Table 45: LED status indicators - Data Panel PC 2100 user's manual V1.17...
Page 56: If Option Slot (If1, Ifx)
Interface card - 2x RS422/485 interfaces - For APC2100/ PPC2100 5ACCIF01.ICAN-000 Interface card - 1x CAN interface - For APC2100/ PPC2100 Table 46: IF1 IF option, IFx slot Information: Interface options can only be installed and replaced by B&R. Panel PC 2100 user's manual V1.17...
Page 57: Features Of Ap1000 Panels
Panels with keys are delivered with transparent slide-in labels inserted in the function keys for custom labeling. It is also possible to download a template for slide-in labels with individual captions from the B&R website (www.br- automation.com). The slide-in label slots are accessible on the back of Automation Panel devices. Panel PC 2100 user's manual V1.17...
Page 58: Key And Led Configuration
Hardware number of LED Hardware number of LED Hardware number of key Key without LED Key with LED Figure 24: Representation of keys and LEDs 5AP1151.0573-000 Figure 25: 5AP1151.0573-000 - Key and LED configuration Panel PC 2100 user's manual V1.17...
Page 59 Technical data 5AP1180.1043-000 Figure 26: 5AP1180.1043-000 - Key and LED configuration 5AP1181.1043-000 Figure 27: 5AP1181.1043-000 - Key and LED configuration Panel PC 2100 user's manual V1.17...
Page 60 Technical data 5AP1182.1043-000 Figure 28: 5AP1182.1043-000 - Key and LED configuration 5AP1180.1505-000 Figure 29: 5AP1180.1505-000 - Key and LED configuration Panel PC 2100 user's manual V1.17...
Page 61 Technical data 5AP1181.1505-000 Figure 30: 5AP1181.1505-000 - Key and LED configuration Panel PC 2100 user's manual V1.17...
Page 62: Usb Interface
The interfaces, etc. available on the device or module have been numbered as such for the purpose of clear differentiation. This numbering may deviate from the numbering used by the respective operating system, however. The USB interface is protected by a maintenance-free "USB current-limiting switch" (max. 500 mA). Panel PC 2100 user's manual V1.17...
Page 63: Mounting Compatibility
323 x 358 Vertical1 ● ● ▲ ▲ ▲ ▲ Installation dimensions 303 x 336 303 x 336 303 x 341 303 x 341 303 x 341 303 x 341 Table 49: Overview of device compatibility Panel PC 2100 user's manual V1.17...
Page 64 566 x 447 Table 49: Overview of device compatibility The device name "AP1000" refers to the Automation Panel 1000 as well as Panel PC 900 and Panel PC 2100 systems with an installed AP1000 panel. Panel PC 2100 user's manual V1.17...
Page 65: Compatibility Details
Outer contour of device Cutout for device Figure 32: Mounting compatibility - 5.7" device - Horizontal1 5.7" Automation Panel 1000, Power Panel 500 devices and Power Panel 100/200/300/400 devices are 100% mounting compatible in the Horizontal1 format. Panel PC 2100 user's manual V1.17...
Page 66 • When mounting, make sure that the PP100/200/300/400 devices are placed and mounted as close to the center of the cutout as possible. Failure to do so can prevent the retaining clips from holding firmly, which means that a solid seal is no longer guaranteed by the gasket (IP65). Panel PC 2100 user's manual V1.17...
Page 67 • When mounting, make sure that the PP100/200/300/400 devices are placed and mounted as close to the center of the cutout as possible. Failure to do so can prevent the retaining clips from holding firmly, which means that a solid seal is no longer guaranteed by the gasket (IP65). Panel PC 2100 user's manual V1.17...
Page 68 • When mounting, make sure that the PP100/200/300/400 devices are placed and mounted as close to the center of the cutout as possible. Failure to do so can prevent the retaining clips from holding firmly, which means that a solid seal is no longer guaranteed by the gasket (IP65). Panel PC 2100 user's manual V1.17...
Page 69 The larger cutout can be used for all devices under certain conditions: • When mounting, make sure that the AP1000, AP900, PPC700 and PP500 devices are placed and mounted as close to the center of the cutout as possible. Panel PC 2100 user's manual V1.17...
Page 70 Failure to do so can prevent the retaining clips from holding firmly, which means that a solid seal is no longer guaranteed by the gasket (IP65). Panel PC 2100 user's manual V1.17...
Page 71 Cutout for device Figure 42: Mounting compatibility - 19" device - Horizontal1 19" Automation Panel 1000, Automation Panel 900, Panel PC 700 and Panel PC 800 are 100% mounting com- patible in the Horizontal1 format. Panel PC 2100 user's manual V1.17...
Page 72 The cutout tolerance for the AP1000 is +0 mm / -0.5 mm. 583 x 464 566 x 447 AP900 Outer contour of device Cutout for device Figure 43: Mounting compatibility - 21.3" device - Horizontal1 Panel PC 2100 user's manual V1.17...
Page 73: Individual Components
Direction U = 80° / Direction D = 80° Backlight Type Brightness (dimmable) Typ. 25 to 500 cd/m² Half-brightness time 50,000 h Touch screen Type Technology Analog, resistive Controller B&R, serial, 12-bit Transmittance 81% ±3% Table 51: 5AP923.1215-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 74 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). 2.3.1.1.4 Dimensions Figure 44: 5AP923.1215-00 - Dimensions 2.3.1.1.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 45: 5AP923.1215-00 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 75: 5Ap923.1505-00
Typ. 20 to 400 cd/m² Half-brightness time 50,000 h Touch screen Type Technology Analog, resistive Controller B&R, serial, 12-bit Transmittance 81% ±3% Operating conditions Pollution degree per EN 61131-2 Pollution degree 2 Table 53: 5AP923.1505-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 76 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). 2.3.1.2.4 Dimensions Figure 46: 5AP923.1505-00 - Dimensions 2.3.1.2.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 47: 5AP923.1505-00 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 77: 5Ap923.1906-00
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 55: 5AP923.1906-00, 5AP923.1906-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 78 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). 2.3.1.3.4 Dimensions Figure 48: 5AP923.1906-00 - Dimensions 2.3.1.3.5 Temperature/Humidity diagram Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 49: 5AP923.1906-00 ≤Rev. D0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 79 Technical data Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 50: 5AP923.1906-00 ≥Rev. E0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 80: 5Ap933.156B-00
Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Mechanical properties Front Frame Aluminum, coated Design Black Gasket 3 mm built-in gasket Table 57: 5AP933.156B-00, 5AP933.156B-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 81 At an ambient temperature of 25°C. Reducing the brightness by 50% can increase the half-brightness time by approximately 50%. 2.3.1.4.4 Dimensions Figure 51: 5AP933.156B-00 - Dimensions 2.3.1.4.5 Temperature/Humidity diagram Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 52: 5AP933.156B-00 ≤C0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 82 Technical data Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 53: 5AP933.156B-00 ≥D0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 83: 5Ap933.185B-00
Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Mechanical properties Front Frame Aluminum, coated Design Black Gasket 3 mm built-in gasket Table 59: 5AP933.185B-00, 5AP933.185B-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 84 At an ambient temperature of 25°C. Reducing the brightness by 50% can increase the half-brightness time by approximately 50%. 2.3.1.5.4 Dimensions Figure 54: 5AP933.185B-00 - Dimensions 2.3.1.5.5 Temperature/Humidity diagram Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 55: 5AP933.185B-00 ≤C0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 85 Technical data Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 56: 5AP933.185B-00 ≥D0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 86: 5Ap933.215C-00
Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Mechanical properties Front Frame Aluminum, coated Design Black Gasket 3 mm built-in gasket Table 61: 5AP933.215C-00, 5AP933.215C-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 87 At an ambient temperature of 25°C. Reducing the brightness by 50% can increase the half-brightness time by approximately 50%. 2.3.1.6.4 Dimensions 541.5 Figure 57: 5AP933.215C-00 - Dimensions 2.3.1.6.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 58: 5AP933.215C-00 ≤C0 - Temperature/Humidity diagrams Panel PC 2100 user's manual V1.17...
Page 88 Technical data Operation Temperature [°C] Figure 59: 5AP933.215C-00 ≥D0 - Temperature/Humidity diagrams Panel PC 2100 user's manual V1.17...
Page 89: 5Ap933.240C-00
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 63: 5AP933.240C-00, 5AP933.240C-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 90 At an ambient temperature of 25°C. Reducing the brightness by 50% can increase the half-brightness time by approximately 50%. 2.3.1.7.4 Dimensions 598.5 Figure 60: 5AP933.240C-00 - Dimensions 2.3.1.7.5 Temperature/Humidity diagram Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 61: 5AP933.240C-00 ≤C0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 91 Technical data Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 62: 5AP933.240C-00 ≥D0 - Temperature/Humidity diagrams Panel PC 2100 user's manual V1.17...
Page 92: Ap1000 Panels
Half-brightness time 50,000 h Touch screen Type Technology Analog, resistive Controller B&R, serial, 12-bit Transmittance 81% ±3% Operating conditions Pollution degree per EN 61131-2 Pollution degree 2 Table 65: 5AP1120.0573-000, 5AP1120.0573-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 93 5.7" AP1000 panels are supported starting with the following firmware versions: • Firmware V3.11 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V4.08 or later for SDL3 receiver 5DLSD3.1001-00 • V1.03 for the 5PPC2100.BYxx-000 PPC2100 system unit Panel PC 2100 user's manual V1.17...
Page 94 Technical data 2.3.2.1.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 64: 5AP1120.0573-000 - Temperature/humidity diagram Panel PC 2100 user's manual V1.17...
Page 95: 5Ap1151.0573-000
22 with LED (yellow) System keys Numeric keys, cursor block Service life >1,000,000 actuations at 1 ±0.3 N to 3 ±0.3 N actuating force LED brightness Yellow Typ. 38 mcd Table 67: 5AP1151.0573-000, 5AP1151.0573-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 96 5.7" AP1000 panels are supported starting with the following firmware versions: • Firmware V3.11 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V4.08 or later for SDL3 receiver 5DLSD3.1001-00 • V1.03 for the 5PPC2100.BYxx-000 PPC2100 system unit Panel PC 2100 user's manual V1.17...
Page 97 Technical data 2.3.2.2.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 66: 5AP1151.0573-000 - Temperature/humidity diagram Panel PC 2100 user's manual V1.17...
Page 98: 5Ap1120.0702-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 69: 5AP1120.0702-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 99 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.3.4 Dimensions Figure 67: 5AP1120.0702-000 - Dimensions 2.3.2.3.5 Temperature/Humidity diagram Operation Storage/Transport Temperature [°C] Figure 68: 5AP1120.0702-000 - Temperature/humidity diagram Panel PC 2100 user's manual V1.17...
Page 100: 5Ap1130.0702-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 71: 5AP1130.0702-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 101 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.4.4 Dimensions Figure 69: 5AP1130.0702-000 - Dimensions 2.3.2.4.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 70: 5AP1130.0702-000 - Temperature/humidity diagram Panel PC 2100 user's manual V1.17...
Page 102: 5Ap1120.101E-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 73: 5AP1120.101E-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 103 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.5.4 Dimensions Figure 71: 5AP1120.101E-000 - Dimensions 2.3.2.5.5 Temperature/Humidity diagram Operation Storage/Transport Temperature [°C] Figure 72: 5AP1120.101E-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 104: 5Ap1130.101E-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 75: 5AP1130.101E-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 105 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.6.4 Dimensions Figure 73: 5AP1130.101E-000 - Dimensions 2.3.2.6.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 74: 5AP1130.101E-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 106: 5Ap1120.1043-000
Direction R = 80° / Direction L = 80° Vertical Direction U = 80° / Direction D = 80° Backlight Type Brightness (dimmable) Typ. 22.5 to 450 cd/m² Half-brightness time 70,000 h Table 77: 5AP1120.1043-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 107 • Firmware V3.11 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V4.08 or later for SDL3 receiver 5DLSD3.1001-00 • Firmware V1.03 or later for PPC2100 system unit 5PPC2100.BYxx-000 • Firmware V1.18 or later for PPC900 system unit 5PC901.TS77-xx Panel PC 2100 user's manual V1.17...
Page 108 Technical data 2.3.2.7.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 76: 5AP1120.1043-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 109: 5Ap1180.1043-000
Direction R = 80° / Direction L = 80° Vertical Direction U = 80° / Direction D = 80° Backlight Type Brightness (dimmable) Typ. 22.5 to 450 cd/m² Half-brightness time 70,000 h Table 79: 5AP1180.1043-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 110 • Firmware V3.11 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V4.08 or later for SDL3 receiver 5DLSD3.1001-00 • Firmware V1.03 or later for PPC2100 system unit 5PPC2100.BYxx-000 • Firmware V1.18 or later for PPC900 system unit 5PC901.TS77-xx Panel PC 2100 user's manual V1.17...
Page 111 Technical data 2.3.2.8.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 78: 5AP1180.1043-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 112: 5Ap1181.1043-000
VGA, 640 x 480 pixels Contrast 900:1 Viewing angles Horizontal Direction R = 80° / Direction L = 80° Vertical Direction U = 80° / Direction D = 80° Table 81: 5AP1181.1043-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 113 Figure 79: 5AP1181.1043-000 - Dimensions 2.3.2.9.5 Requirements 10.4" AP1000 panels are supported starting with the following firmware versions: • Firmware V3.11 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V4.08 or later for SDL3 receiver 5DLSD3.1001-00 Panel PC 2100 user's manual V1.17...
Page 114 Technical data • Firmware V1.03 or later for PPC2100 system unit 5PPC2100.BYxx-000 • Firmware V1.18 or later for PPC900 system unit 5PC901.TS77-xx 2.3.2.9.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 80: 5AP1181.1043-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 115: 5Ap1182.1043-000
Direction R = 80° / Direction L = 80° Vertical Direction U = 80° / Direction D = 80° Backlight Type Brightness (dimmable) Typ. 22.5 to 450 cd/m² Half-brightness time 70,000 h Table 83: 5AP1182.1043-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 116 • Firmware V3.11 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V4.08 or later for SDL3 receiver 5DLSD3.1001-00 • Firmware V1.03 or later for PPC2100 system unit 5PPC2100.BYxx-000 • Firmware V1.18 or later for PPC900 system unit 5PC901.TS77-xx Panel PC 2100 user's manual V1.17...
Page 117 Technical data 2.3.2.10.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 82: 5AP1182.1043-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 118: 5Ap1120.1214-000
Direction R = 89° / Direction L = 89° Vertical Direction U = 89° / Direction D = 89° Backlight Type Brightness (dimmable) Typ. 22.5 to 450 cd/m² Half-brightness time 50,000 h Table 85: 5AP1120.1214-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 119 Touch screen drivers for approved operating systems are available in the Downloads section of the B&R website. There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.11.4 Dimensions Figure 83: 5AP1120.1214-000 - Dimensions Panel PC 2100 user's manual V1.17...
Page 120 Technical data 2.3.2.11.5 Temperature/Humidity diagram Operation Storage/Transport Temperature [°C] Figure 84: 5AP1120.1214-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 121: 5Ap1120.121E-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 87: 5AP1120.121E-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 122 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.12.4 Dimensions Figure 85: 5AP1120.121E-000 - Dimensions 2.3.2.12.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 86: 5AP1120.121E-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 123: 5Ap1130.121E-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 89: 5AP1130.121E-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 124 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.13.4 Dimensions Figure 87: 5AP1130.121E-000 - Dimensions 2.3.2.13.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 88: 5AP1130.121E-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 125: 5Ap1120.1505-000
Direction R = 80° / Direction L = 80° Vertical Direction U = 70° / Direction D = 70° Backlight Type Brightness (dimmable) Typ. 20 to 400 cd/m² Half-brightness time 50,000 h Table 91: 5AP1120.1505-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 126 Touch screen drivers for approved operating systems are available in the Downloads section of the B&R website. There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.14.4 Dimensions Figure 89: 5AP1120.1505-000 - Dimensions Panel PC 2100 user's manual V1.17...
Page 127 Technical data 2.3.2.14.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 90: 5AP1120.1505-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 128: 5Ap1180.1505-000
Direction R = 80° / Direction L = 80° Vertical Direction U = 70° / Direction D = 70° Backlight Type Brightness (dimmable) Typ. 20 to 400 cd/m² Half-brightness time 50,000 h Table 93: 5AP1180.1505-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 129 Touch screen drivers for approved operating systems are available in the Downloads section of the B&R website. There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.15.4 Dimensions Figure 91: 5AP1180.1505-000 - Dimensions Panel PC 2100 user's manual V1.17...
Page 130 Technical data 2.3.2.15.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 92: 5AP1180.1505-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 131: 5Ap1181.1505-000
Low speed (1.5 Mbit/s), full speed (12 Mbit/s), high speed (480 Mbit/s) Current-carrying capacity Max. 500 mA Display Type TFT color Diagonal 15.0" Colors 16.7 million Resolution XGA, 1024 x 768 pixels Table 95: 5AP1181.1505-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 132 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). There may be visible deviations in the color and surface appearance depending on the process or batch. Panel PC 2100 user's manual V1.17...
Page 133 • Firmware V03.15 or later for SDL/DVI receiver 5DLSDL.1001-00 • Firmware V04.11 or later for SDL3 receiver 5DLSD3.1001-00 • Firmware V06.12 or later for SDL4 receiver 5DLSD4.1001-00 2.3.2.16.6 Temperature/Humidity diagram Operation Temperature [°C] Figure 94: 5AP1181.1505-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 134 Technical data 2.3.2.16.7 Cutout installation Outer contour (Automation Panel) 421.5 Cutout Cutout dimensions 415 ±0.5 mm x 413 ±0.5 mm Figure 95: 5AP1181.1505-000 - Cutout installation Panel PC 2100 user's manual V1.17...
Page 135: 5Ap1120.156B-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 97: 5AP1120.156B-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 136 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.17.4 Dimensions Figure 96: 5AP1120.156B-000 - Dimensions 2.3.2.17.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 97: 5AP1120.156B-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 137: 5Ap1130.156C-000
Brightness (dimmable) Typ. 40 to 400 cd/m² Half-brightness time 70,000 h Touch screen Type Technology Projected capacitive touch (PCT) Controller Transmittance See section "Touch screen" in appendix A. Table 99: 5AP1130.156C-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 138 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.18.4 Dimensions Figure 98: 5AP1130.156C-000 - Dimensions 2.3.2.18.5 Temperature/Humidity diagram Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 99: 5AP1130.156C-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 139: 5Ap1130.185C-000
Degree of protection per EN 60529 Front: IP65 Back: IP20 (only with installed link module or installed system unit) Protection per UL 50 Front: Type 4X indoor use only Table 101: 5AP1130.185C-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 140 There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.19.4 Dimensions Figure 100: 5AP1130.185C-000 - Dimensions 2.3.2.19.5 Temperature/Humidity diagram Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 101: 5AP1130.185C-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 141: 5Ap1120.1906-000
SXGA, 1280 x 1024 pixels Contrast 1500:1 Viewing angles Horizontal Direction R = 85° / Direction L = 85° Vertical Direction U = 85° / Direction D = 85° Table 103: 5AP1120.1906-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 142 Touch screen drivers for approved operating systems are available for download in the Downloads section of the B&R website (www.br-automation.com). There may be visible deviations in the color and surface appearance depending on the process or batch. 2.3.2.20.4 Dimensions Figure 102: 5AP1120.1906-000 - Dimensions Panel PC 2100 user's manual V1.17...
Page 143 Technical data 2.3.2.20.5 Temperature/Humidity diagram Operation Temperature [°C] Figure 103: 5AP1120.1906-000 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 144: System Units
PPC2100/APC2200/PPC2200 - Only available with a new de- vice 5ACCIF01.ICAN-000 Interface card - 1x CAN interface - For APC2100/PPC2100/ APC2200/PPC2200 - Only available with a new device Table 104: 5PPC2100.BY01-000, 5PPC2100.BY11-000, 5PPC2100.BY22-000, 5PPC2100.BY34-000, 5PPC2100.BY44-000, 5PPC2100.BY48-000 - Order data Panel PC 2100 user's manual V1.17...
Page 145 Transfer rate Low speed (1.5 Mbit/s), full speed (12 Mbit/s), high speed (480 Mbit/s), SuperSpeed (5 Gbit/s) Current-carrying capacity Max. 1 A per connection Table 105: 5PPC2100.BY01-000, 5PPC2100.BY11-000, 5PPC2100.BY22-000, 5PPC2100.BY34-000, 5PPC2100.BY44-000, 5PPC2100.BY48-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 146 EN 60950 requirements must be observed; see section "+24 VDC power supply" in the user's manual. Only when all interface covers are installed. The maximum ambient temperature is typically derated by 1°C per 1000 meters (starting at 500 meters above sea level). Panel PC 2100 user's manual V1.17...
Page 147: Cfast Cards
Self-Monitoring, Analysis and Reporting Technology (S.M.A.R.T.) is an industry standard for mass storage devices that was introduced to monitor important parameters and detect imminent failures. Critical performance and cali- bration data is monitored and stored in an effort to predict the probability of error states. Panel PC 2100 user's manual V1.17...
Page 148 Example for an MLC CFast card over the period of a week: 2.3.4.2.6 Dimensions 42.8 ±0.1 2.3 ±0.1 +0.2 -0.1 1.15 ±0.1 1 ±0.1 41.6 ±0.13 0.6 ±0.07 1 ±0.07 1 ±0.07 Bottom 1 ±0.1 6.35 33.96 ±0.15 Figure 104: CFast card - Dimensions Panel PC 2100 user's manual V1.17...
Page 149: 5Cfast.xxxx-00
46 MB/s Maximum With 128 kB block size 100 MB/s 115 MB/s 115 MB/s 115 MB/s 120 MB/s With 4 kB block size 50 MB/s Table 107: 5CFAST.2048-00, 5CFAST.4096-00, 5CFAST.8192-00, 5CFAST.016G-00, 5CFAST.032G-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 150 10 to 2000 Hz: 20 g peak Shock Operation 1500 g peak, 0.5 ms Storage 1500 g peak, 0.5 ms Transport 1500 g peak, 0.5 ms Table 107: 5CFAST.2048-00, 5CFAST.4096-00, 5CFAST.8192-00, 5CFAST.016G-00, 5CFAST.032G-00 - Technical data Panel PC 2100 user's manual V1.17...
Page 151 Figure 105: 5CFAST.xxxx-00 - Temperature/Humidity diagram 2.3.4.3.5 Dimensions 42.8 ±0.1 2.3 ±0.1 +0.2 -0.1 1.15 ±0.1 1 ±0.1 41.6 ±0.13 0.6 ±0.07 1 ±0.07 1 ±0.07 Bottom 1 ±0.1 6.35 33.96 ±0.15 Figure 106: CFast card - Dimensions Panel PC 2100 user's manual V1.17...
Page 152: 5Cfast.xxxx-10
128 GB 256 GB Data retention 10 years Data reliability <1 unrecoverable error per 10 bits read Lifetime monitoring MTBF >2,000,000 hours (at 25°C) Maintenance None Table 110: 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10, 5CFAST.256G-10 - Technical data Panel PC 2100 user's manual V1.17...
Page 153 10 to 2000 Hz: 20 g peak Shock Operation 1500 g peak, 0.5 ms Storage 1500 g peak, 0.5 ms Transport 1500 g peak, 0.5 ms Table 110: 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10, 5CFAST.256G-10 - Technical data Panel PC 2100 user's manual V1.17...
Page 154 Guaranteed 86.4 TBW 172.8 TBW 345.6 TBW Erase/Write cycles Guaranteed 3000 Wear leveling Static Error correction coding (ECC) S.M.A.R.T. support Support Hardware APC2100, APC910, PPC2100, PPC900 Table 111: 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10 - Technical data Panel PC 2100 user's manual V1.17...
Page 155 Yes, although applies only if all components installed in the complete system have this certification and are listed on the associated DNV GL certificate for the product family. TBW = Terabytes written Sequential access without a file system Panel PC 2100 user's manual V1.17...
Page 156 Temperature [°C] Figure 107: 5CFAST.032G-10 ≥Rev. G0, 5CFAST.064G-10 ≥Rev. E0, 5CFAST.128G-10 ≥Rev. E0, 5CFAST.256G-10 - Temperature/Humidity diagram Operation Temperature [°C] Figure 108: 5CFAST.032G-10 ≤Rev. F0, 5CFAST.064G-10 ≤Rev. D0, 5CFAST.128G-10 ≤Rev. D0 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 157 If an operating system is installed on the CFast card, write protection must be disabled. Disabled Enabled Figure 109: CFast card - Write protection Write protection is only present on the following CFast cards: • 5CFAST.032G-10 ≤Rev. F0 • 5CFAST.064G-10 ≤Rev. D0 • 5CFAST.128G-10 ≤Rev. D0 Panel PC 2100 user's manual V1.17...
Page 158: Interface Options
Class I, Division 2, Groups ABCD, T4 DNV GL Temperature: B (0 - 55°C) Humidity: B (up to 100%) Vibration: A (0.7 g) EMC: B (Bridge and open deck) Table 113: 5ACCIF01.FPCC-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 159 The interfaces, etc. available on the device or module have been numbered as such for the purpose of clear differentiation. This numbering may deviate from the numbering used by the respective operating system, however. This interface is referred to as IF1 in Automation Studio / Automation Runtime. Panel PC 2100 user's manual V1.17...
Page 160 Table 117: CAN1 - Bus length and transfer rate The specified cable length is only valid with the values specified in Tab. 116 "CAN driver settings". Cable lengths additionally depend on the values in the timing register. Panel PC 2100 user's manual V1.17...
Page 161 This interface can only be used in Automation Runtime and is referred to as IF4 in Automation Studio / Automation Runtime. It is not a "PC interface" and therefore not shown in BIOS. Panel PC 2100 user's manual V1.17...
Page 162 1x 0.34 mm² (22 AWG / 19), tinned copper stranded wire Wire insulation Conductor resistance ≤59 Ω/km Outer jacket Material PUR compound Properties Halogen-free Complete shielding Composed of tinned copper wires Table 123: CAN cable requirements Panel PC 2100 user's manual V1.17...
Page 163 Ethernet mode In this mode, the interface is operated as an Ethernet interface. Green - Status Description The interface is being operated as an Ethernet interface. Table 126: LED "Status/Error" - Ethernet mode Panel PC 2100 user's manual V1.17...
Page 164 The module can be configured by the MN in this state. The CN waits until it receives an SoC frame and then switches to state PRE_OPERATIONAL_2 (double flash). A solid red LED in this state indicates failure of the MN. Table 128: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 165 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 166: 5Accif01.Fpcs-000
Max. baud rate 115 kbit/s POWERLINK Quantity Transfer 100BASE-TX Type Type 4 Design Shielded RJ45 Transfer rate 100 Mbit/s Cable length Max. 100 m between two stations (segment length) Table 131: 5ACCIF01.FPCS-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 167 Serial interface COM - IFx 1)2) RS485 Type RS485, not electrically isolated UART 16550-compatible, 16-byte FIFO 10-pin, male Transfer rate Max. 115 kbit/s Bus length Max. 1200 m Assignment Shield 8 10 Table 133: 5ACCIF01.FPCS-000 - COM interface Panel PC 2100 user's manual V1.17...
Page 168 This interface can only be used in Automation Runtime and is referred to as IF3 in Automation Studio / Automation Runtime. It is not a "PC interface" and therefore not shown in BIOS. Panel PC 2100 user's manual V1.17...
Page 169 The terminating resistor is switched off. Terminating resistor Table 140: Terminating resistor 2.3.5.2.3.5 Shielding For the interfaces on the 10-pin female connector, the interface shield can be put on pin 2 of the female connector. Panel PC 2100 user's manual V1.17...
Page 170 If an error occurs in the following states, then the green LED blinks over the red LED: • BASIC_ETHERNET • PRE_OPERATIONAL_1 • PRE_OPERATIONAL_2 • READY_TO_OPERATE Status Green Error LED "S/E" Table 143: LED "Status/Error" - POWERLINK - Error Panel PC 2100 user's manual V1.17...
Page 171 No output data is output, and no input data is provided. It is only possible to enter or leave this mode by a corresponding command from the MN. Table 144: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 172 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 173: 5Accif01.Fplk-000
Controller nvSRAM Size 512 kB Data retention 20 years Read/Write endurance Min. 1,000,000 Remanent variables in power failure mode 256 kB (e.g. for Automation Runtime, see Automation Help) Table 147: 5ACCIF01.FPLK-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 174 The interfaces, etc. available on the device or module have been numbered as such for the purpose of clear differentiation. This numbering may deviate from the numbering used by the respective operating system, however. Panel PC 2100 user's manual V1.17...
Page 175 If an error occurs in the following states, then the green LED blinks over the red LED: • BASIC_ETHERNET • PRE_OPERATIONAL_1 • PRE_OPERATIONAL_2 • READY_TO_OPERATE Status Green Error LED "S/E" Table 152: LED "Status/Error" - POWERLINK - Error Panel PC 2100 user's manual V1.17...
Page 176 No output data is output, and no input data is provided. It is only possible to enter or leave this mode by a corresponding command from the MN. Table 153: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 177 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 178: 5Accif01.Fpls-000
Max. baud rate 115 kbit/s POWERLINK Quantity Transfer 100BASE-TX Type Type 4 Design Shielded RJ45 Transfer rate 100 Mbit/s Cable length Max. 100 m between two stations (segment length) Table 156: 5ACCIF01.FPLS-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 179 This interface (if available) is enabled automatically in BIOS as COMA with default I/O address 3F8h and IRQ 4. This interface is referred to as IF5 in Automation Studio / Automation Runtime. Panel PC 2100 user's manual V1.17...
Page 180 If an error occurs in the following states, then the green LED blinks over the red LED: • BASIC_ETHERNET • PRE_OPERATIONAL_1 • PRE_OPERATIONAL_2 • READY_TO_OPERATE Status Green Error LED "S/E" Table 161: LED "Status/Error" - POWERLINK - Error Panel PC 2100 user's manual V1.17...
Page 181 No output data is output, and no input data is provided. It is only possible to enter or leave this mode by a corresponding command from the MN. Table 162: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 182 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 183: 5Accif01.Fpls-001
100 Mbit/s Cable length Max. 100 m between two stations (segment length) Electrical characteristics Power consumption 1.5 W Operating conditions Pollution degree per EN 61131-2 Pollution degree 2 Table 165: 5ACCIF01.FPLS-001 - Technical data Panel PC 2100 user's manual V1.17...
Page 184 This interface (if available) is enabled automatically in BIOS as COMA with default I/O address 3F8h and IRQ 4. This interface is referred to as IF5 in Automation Studio / Automation Runtime. Panel PC 2100 user's manual V1.17...
Page 185 If an error occurs in the following states, then the green LED blinks over the red LED: • BASIC_ETHERNET • PRE_OPERATIONAL_1 • PRE_OPERATIONAL_2 • READY_TO_OPERATE Status Green Error LED "S/E" Table 170: LED "Status/Error" - POWERLINK - Error Panel PC 2100 user's manual V1.17...
Page 186 No output data is output, and no input data is provided. It is only possible to enter or leave this mode by a corresponding command from the MN. Table 171: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 187 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 188: 5Accif01.Fpsc-000
(e.g. for Automation Runtime, see Automation Help) Interfaces Quantity Type RS232, not modem-capable, not electrically isolated Design 10-pin, male UART 16550-compatible, 16-byte FIFO Max. baud rate 115 kbit/s Table 174: 5ACCIF01.FPSC-000 - Technical data Panel PC 2100 user's manual V1.17...
Page 189 The interfaces, etc. available on the device or module have been numbered as such for the purpose of clear differentiation. This numbering may deviate from the numbering used by the respective operating system, however. This interface is referred to as IF1 in Automation Studio / Automation Runtime. Panel PC 2100 user's manual V1.17...
Page 190 The type of cable to be used depends largely on the required bus length and number of nodes. The bus length is determined by the bit rate. In accordance with CiA (CAN in Automation), the maximum bus length is 1000 meters. The following bus lengths are permitted with a maximum oscillator tolerance of 0.121%: Panel PC 2100 user's manual V1.17...
Page 191 Indicates a connection to a POWERLINK net- work. Blinking POWERLINK Link LED Data transfer in progress. Green-Red POWERLINK Status/Error LED "LED "Status/Error"". POWERLINK Status/Error LED "LED "Status/Error"". Table 182: 5ACCIF01.FPSC-000 - LED status indicators Panel PC 2100 user's manual V1.17...
Page 192 The module can be configured by the MN in this state. The CN waits until it receives an SoC frame and then switches to state PRE_OPERATIONAL_2 (double flash). A solid red LED in this state indicates failure of the MN. Table 185: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 193 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 194: 5Accif01.Fpsc-001
(e.g. for Automation Runtime, see Automation Help) Interfaces Quantity Type RS232, not modem-capable, not electrically isolated Design 10-pin, male UART 16550-compatible, 16-byte FIFO Max. baud rate 115 kbit/s Table 188: 5ACCIF01.FPSC-001 - Technical data Panel PC 2100 user's manual V1.17...
Page 195 The interfaces, etc. available on the device or module have been numbered as such for the purpose of clear differentiation. This numbering may deviate from the numbering used by the respective operating system, however. This interface is referred to as IF1 in Automation Studio / Automation Runtime. Panel PC 2100 user's manual V1.17...
Page 196 The type of cable to be used depends largely on the required bus length and number of nodes. The bus length is determined by the bit rate. In accordance with CiA (CAN in Automation), the maximum bus length is 1000 meters. The following bus lengths are permitted with a maximum oscillator tolerance of 0.121%: Panel PC 2100 user's manual V1.17...
Page 197 This interface can only be used in Automation Runtime and is referred to as IF2 in Automation Studio / Automation Runtime. It is not a "PC interface" and therefore not shown in BIOS. Panel PC 2100 user's manual V1.17...
Page 198 If an error occurs in the following states, then the green LED blinks over the red LED: • BASIC_ETHERNET • PRE_OPERATIONAL_1 • PRE_OPERATIONAL_2 • READY_TO_OPERATE Status Green Error LED "S/E" Table 199: LED "Status/Error" - POWERLINK - Error Panel PC 2100 user's manual V1.17...
Page 199 No output data is output, and no input data is provided. It is only possible to enter or leave this mode by a corresponding command from the MN. Table 200: LED "Status/Error" - POWERLINK - Status Panel PC 2100 user's manual V1.17...
Page 200 The firmware is a component of Automation Studio. The module is updated to this version automatically. To update the firmware included in Automation Studio, the hardware must be upgraded (see "Project manage- ment" / "The workspace" / "Upgrades" in Automation Help). Panel PC 2100 user's manual V1.17...
Page 201: 5Accif01.Fss0-000
Mechanical characteristics Weight 25 g Table 203: 5ACCIF01.FSS0-000 - Technical data Yes, although applies only if all components installed in the complete system have this certification and the complete system bears the corresponding mark. Panel PC 2100 user's manual V1.17...
Page 202 The voltage drop resulting from long cable lengths can result in greater potential differences between the bus stations, which can hinder communication. This can be improved by running the ground wire with the others. Panel PC 2100 user's manual V1.17...
Page 203 The voltage drop resulting from long cable lengths can result in greater potential differences between the bus stations, which can hinder communication. This can be improved by running the ground wire with the others. Panel PC 2100 user's manual V1.17...
Page 204 1x 0.34 mm² (22 AWG / 19), tinned copper stranded wire Wire insulation Conductor cross section ≤59 Ω/km Outer jacket Material PUR compound Properties Halogen-free Complete shielding Composed of tinned copper wires Table 209: RS485 - Cable requirements Panel PC 2100 user's manual V1.17...
Page 205 • Panel PC 2100: V1.10 The firmware can be downloaded from the B&R website (www.br-automation.com). For information about firmware upgrades, see section "Upgrading the firmware on the Panel PC 2100" on page 273. 2.3.5.8.3.9 Hardware The following minimum hardware revisions are required on the PC to ensure the functionality of the interface option: •...
Page 206: 5Accif01.Ican-000
Mechanical characteristics Weight 25 g Table 213: 5ACCIF01.ICAN-000 - Technical data Yes, although applies only if all components installed in the complete system have this certification and the complete system bears the corresponding mark. Panel PC 2100 user's manual V1.17...
Page 207 The following bus lengths are permitted with a maximum oscillator tolerance of 0.121%: Extension Transfer rate ≤1000 m Typ. 50 kbit/s ≤200 m Typ. 250 kbit/s ≤100 m Typ. 500 kbit/s ≤20 m Typ. 1 Mbit/s Table 217: CAN - Bus length and transfer rate Panel PC 2100 user's manual V1.17...
Page 208 • Automation PC 2100: V1.06 • Panel PC 2100: V1.06 The firmware can be downloaded from the B&R website (www.br-automation.com). For information about firmware upgrades, see section "Upgrading the firmware on the Panel PC 2100" on page 273. Panel PC 2100 user's manual V1.17...
Page 209 Technical data 2.3.5.9.3.5 Drivers In Windows 7 and later, the CAN IF option is supported by PVI V4.2.5 or Windows CAN driver V3.0. Panel PC 2100 user's manual V1.17...
Page 210: Commissioning
Moisture can cause short circuits in the electrical circuits and damages the device. • The permissible mounting orientations when installing the device must be observed, see see "Mounting orientations". Panel PC 2100 user's manual V1.17...
Page 211 • Instructions and regulations on the power supply and functional ground must be observed. • The device must be installed in a position that minimizes glare on the screen. • The device must be installed such that viewing is optimized for the user. Panel PC 2100 user's manual V1.17...
Page 212: Installing A Panel Pc With An Ap9X3 Panel
Failure to follow these instructions can result in damage to property. 3.1.2 Installing a Panel PC with an AP9x3 panel The Panel PC 2100 with AP9x3 panel is installed in the cutout using retaining clips. The number of retaining clips depends on the panel.
Page 213 4. Fasten the retaining clips to the wall or control cabinet by alternately tightening the screws with a 2.5 hex key screwdriver. The tightening torque should be max. 1 Nm to provide an optimal seal. 1 - 6 mm Wall or control cabinet plate Figure 114: Fastening the retaining clips (sample figure) Panel PC 2100 user's manual V1.17...
Page 214: Mounting An Automation Panel 1000 With Retaining Clips
Commissioning 3.1.3 Mounting an Automation Panel 1000 with retaining clips The Panel PC 2100 with AP1000 panel is installed in the cutout using retaining clips. The number of retaining clips depends on the panel. The following Automation Panel 1000 panels are mounted using retaining clips: •...
Page 215 4. Fasten the retaining clips to the wall or control cabinet by alternately tightening the screws with a 2.5 hex key screwdriver. The tightening torque should be max. 1 Nm to provide an optimal seal. 1 - 6 mm Wall or control cabinet plate Figure 117: Fastening the retaining clips (sample figure) Panel PC 2100 user's manual V1.17...
Page 216: Mounting An Automation Panel 1000 With Clamping Blocks
Commissioning 3.1.4 Mounting an Automation Panel 1000 with clamping blocks The Panel PC 2100 with AP1000 panel is installed in the cutout using clamping blocks. The number of clamping blocks depends on the panel. The following Automation Panel 1000 panels are mounted using clamping blocks: •...
Page 217 Tightening the screw presses down the integrated clamping lever to hold the device securely in place. The tightening torque should be max. 0.5 Nm to provide an optimal seal. 2 - 10 mm Wall or control cabinet plate Figure 119: Fastening the clamping blocks (sample figure) Panel PC 2100 user's manual V1.17...
Page 218: Installation Information For Individual Components
3.1.5 Installation information for individual components Information: If the Panel PC 2100 is not delivered as a complete system but as individual components (or individual components are installed afterward), then these components must be enabled in BIOS. This is done by launching BIOS when booting the system, loading the default BIOS values and then saving the set- tings.
Page 219: Replacing The System Unit
7. The system unit can now be replaced by following these steps in reverse order. The maximum tightening torque of the Torx screws (T10) is 0.5 Nm. Only the mounting materials included in delivery are permitted to be used to install the system unit. Panel PC 2100 user's manual V1.17...
Page 220: Installation The 4-Port Usb Hub
Commissioning 3.1.7 Installation the 4-port USB hub Installation on the Panel PC 2100 is possible with display diagonals ≥10.1". The USB hub can be installed starting with the following revisions: • 5PPC2100.BY01-000 - Rev. F0 and later • 5PPC2100.BY11-000 - Rev. F0 and later •...
Page 221: Connecting To The Electrical Grid
Observe the pinout of the power supply connection on the device during wiring! Installing a cage clamp terminal block Cage clamp terminals DC power cable 24 VDC Functional ground 0 VDC Terminal contacts Terminal block Figure 124: Installing a cage clamp terminal block Panel PC 2100 user's manual V1.17...
Page 222: Connecting The Power Supply To A B&R Device
0TB103.9 or 0TB103.91, then a cable with maximum 1.5 mm² per connection is possible. • Observe the line shielding concept. All data cables connected to the device must be shielded. The following symbol is used to indicate functional ground on the B&R device: Panel PC 2100 user's manual V1.17...
Page 223 Commissioning Power supply connection +24 VDC (Pin 2) Ground connection Central grounding point Min. 2.5 mm² Min. 1.5 mm² Figure 126: Panel PC 2200 - Grounding concept Panel PC 2100 user's manual V1.17...
Page 224: Cable Connections
The maximum tightening torque for the locating screws is 0.5 Nm. Locating screws Bend radius Locating screws Figure 127: Bend radius - Cable connection Information: For the specified bend radius, see the technical data for the respective cable. Panel PC 2100 user's manual V1.17...
Page 225: Switching On The Device For The First Time
• A USB keyboard and USB mouse are connected (optional). 3.4.2 Switching on the device Procedure 1. Connect and switch on the power supply. 2. The device is in service and booting; LED "Power" is lit. Panel PC 2100 user's manual V1.17...
Page 226: General Instructions For Performing Temperature Testing
A separate application can be developed if it is necessary to collect historical data. Information: Software development kits such as the ADI .NET SDK are available on the B&R website (www.br-au- tomation.com) for developing a separate application. Panel PC 2100 user's manual V1.17...
Page 227: Evaluating With The Burnintest Tool From Passmark
Figure 129: Settings for PassMark BurnInTest Pro V6 using a PPC2100 without IF options Figure 130: Test overview of a PPC2100 without IF options Test properties may need to be fine-tuned depending on the availability of loopback adapters and DVDs. Panel PC 2100 user's manual V1.17...
Page 228 Windows as formatted drives. The test USB must then be deselected, and the USB flash drives must be configured as the testing device in the disk properties. Information: Serial loopback adapters are relatively easy to create. Simply connect some pins on the serial interface with wires. Panel PC 2100 user's manual V1.17...
Page 229: Evaluating Temperatures In Non-Windows Operating Systems
(several hours) observed before beginning the test. Panel PC 2100 user's manual V1.17...
Page 230: Touch Screen Calibration
Microsoft multi-touch drivers are installed when Windows Embedded 8.1 Industry Pro is installed on the device. Once the installation of Windows Embedded 8.1 Industry Pro has completed, the device can be operated imme- diately. Panel PC 2100 user's manual V1.17...
Page 231: Windows 7 Professional / Ultimate
3.6.2.5 Windows Embedded Standard 7 Premium Microsoft multi-touch drivers are installed when Windows Embedded Standard 7 Premium is installed on the device. Once the installation of Windows Embedded Standard 7 Premium has completed, the device can be operated immediately. Panel PC 2100 user's manual V1.17...
Page 232: Adjusting The Display Brightness
The configured brightness is independent of the value configured in BIOS Setup, i.e. the value set in BIOS is used until Windows boots. The value set in BIOS is only applied the first time the Control Center is launched. Panel PC 2100 user's manual V1.17...
Page 233: Known Problems / Issues
Runtime Embedded (ARemb) in graphics-intensive applications, set BIOS setting Advanced - Graphics (IGD) configuration - IGD turbo to Disabled. If BIOS setting Advanced - Graphics (IGD) configu- ration - IGD turbo is set to Disabled, the graphics performance of the system is noticeably reduced. Panel PC 2100 user's manual V1.17...
Page 234: Software
To enter BIOS Setup, the "F2" key must be pressed after the USB controller has been initialized as soon as the following message appears on the monitor (during POST): "F2 = Setup". Figure 132: Boot screen Panel PC 2100 user's manual V1.17...
Page 235: Bios Default Settings
Jumps to the first BIOS menu item or object. Jumps to the last BIOS menu item or object. Resets any changes. Loads and configures CMOS default values for all BIOS settings. Saves and exits. Exits a submenu. Table 222: BIOS-relevant keys Panel PC 2100 user's manual V1.17...
Page 236: Main
The currently configured system time setting. Change the system time Sets system time format This is retained when the system is switched off. Hour:Minute:Second (hh:mm:ss). For details, see the technical data for the sys- tem unit. Table 223: Main Panel PC 2100 user's manual V1.17...
Page 237: System Information
Displays the size of all main memory. None Displays the size of the main memory in slot 1. None Displays the size of the main memory in slot 2. None Table 224: Main - System information Panel PC 2100 user's manual V1.17...
Page 238: Advanced
"SATA configuration" on page 260. Miscellaneous configura- Configures miscellaneous settings. Enter Opens this submenu tion "Miscellaneous configuration" on page 261. Thermal configuration Configures temperature settings. Enter Opens this submenu "Thermal configuration" on page 262. Table 225: Advanced Panel PC 2100 user's manual V1.17...
Page 239: Oem Features
Opens this submenu play. "Display board features" on page 245. IF board features Displays device-specific information for the IF Enter Opens this submenu option. "IF board features" on page 249. Table 226: Advanced - OEM features Panel PC 2100 user's manual V1.17...
Page 240 Option for setting the behavior after a power fail- Stay off The PC remains switched off on power-on. ure. Power on The PC is restarted on power-on. Test interface None Table 227: Advanced - OEM features - Miscellaneous configuration Panel PC 2100 user's manual V1.17...
Page 241 Base address Displays the I/O address. 384h/385h Permanently assigned. This setting cannot be modified. Displays IRQ. Permanently assigned. This setting cannot be modified. Table 228: Advanced - OEM features - Super I/O configuration Panel PC 2100 user's manual V1.17...
Page 242 Enter Opens this submenu "Statistical values" on page 243. Temperature values Displays current temperature values. Enter Opens this submenu "Temperature values" on page 244. Table 229: Advanced - OEM features - System board features Panel PC 2100 user's manual V1.17...
Page 243 Displays the runtime in hours. None Power on cycles Displays the number of power cycles. Each None restart increases the counter by one. Table 230: Advanced - OEM features - System board features - Statistical values Panel PC 2100 user's manual V1.17...
Page 244 Sensor 2 Displays the current temperature of sensor 2 None (system unit sensor 1) in °C and °F (sensor near the CPU). Table 231: Advanced - OEM features - System board features - Temperature values Panel PC 2100 user's manual V1.17...
Page 245 Opens this submenu "Temperature values" on page 247. Panel #15 Displays the panel properties of the panel. Enter Opens this submenu "Panel #15" on page 248. Table 232: Advanced - OEM features - Display board features Panel PC 2100 user's manual V1.17...
Page 246 Displays the runtime in hours. None Power on cycles Displays the number of power cycles. Each None restart increases the counter by one. Table 233: Advanced - OEM features - Display board features - Statistical values Panel PC 2100 user's manual V1.17...
Page 247 Explanation Configuration options Effect Sensor 1 Displays the current temperature of sensor 1 None (display or panel) in °C and °F. Table 234: Advanced - OEM features - Display board features - Temperature values Panel PC 2100 user's manual V1.17...
Page 248 Displays the available keys and LEDs for the None panel. Temperature Displays the temperature of the panel in °C and None °F. Table 235: Advanced - OEM features - Display board features - Panel #15 Panel PC 2100 user's manual V1.17...
Page 249 Displays the manufacturer number. None Parent compatibility ID Displays the manufacturer ID. None Statistical values Displays statistical values. Enter Opens this submenu "Statistical values" on page 250. Table 236: Advanced - OEM features - IF board features Panel PC 2100 user's manual V1.17...
Page 250 Displays the runtime in hours. None Power on cycles Displays the number of power cycles. Each None restart increases the counter by one. Table 237: Advanced - OEM features - IF board features - Statistical values Panel PC 2100 user's manual V1.17...
Page 251: Cpu Configuration
Indicates whether Intel® Hyper-Threading Tech- None Technology nology is supported. CPU power management Configuration of CPU energy settings. Enter Opens this submenu "CPU power management" on page 252. Table 238: Advanced - CPU configuration PROCHOT = Processor hot. Panel PC 2100 user's manual V1.17...
Page 252 Maximum C-State C1. Processor is in sleep mode, switch between C0 and C1. Table 239: Advanced - CPU configuration - CPU power management This setting is only possible if C-States is set to Enabled. Panel PC 2100 user's manual V1.17...
Page 253: Graphics (Igd) Configuration
Disables this function. boost. Enabled Enables this function. IGD - LCD control Configures PPC2100 display settings. Enter Opens this submenu "IGD - LCD control" on page 254. Table 240: Advanced - Graphics (IGD) configuration Panel PC 2100 user's manual V1.17...
Page 254 For example, a dual DVI configuration is auto- matically restored when both DVI monitors are reconnected, even if only one of them was con- nected and enabled during a previous boot. Table 241: Advanced - Graphics (IGD) configuration - IGD configuration Panel PC 2100 user's manual V1.17...
Page 255: Lan
Enabled Enables this function. The Ethernet controller can switch on the system. Network stack Configures the network stack Enter Opens this submenu "Network stack" on page Table 242: Advanced - LAN Panel PC 2100 user's manual V1.17...
Page 256 Option for enabling/disabling IPv4 PXE support. Enabled Enables this function. Disabled Disables this function. IPv6 Option for enabling/disabling IPv6 PXE support. Enabled Enables this function. Disabled Disables this function. Table 243: Advanced - Network stack Panel PC 2100 user's manual V1.17...
Page 257: Pci Express Configuration
PCI Express root port 3 Configures PCI Express settings on port 3 Enter Opens this submenu (ETH1) (ETH1). "PCI Express root port 0 to 3" on page 258. Table 244: Advanced - PCI express configuration Panel PC 2100 user's manual V1.17...
Page 258 Assign INT to root port Option for enabling/disabling the IRQ for the Enabled Enables this function. root port. Disabled Disables this function. Table 245: Advanced - PCI Express configuration - PCI Express root port Panel PC 2100 user's manual V1.17...
Page 259: Usb Configuration
Enables this USB interface. USB port #3 Option for enabling/disabling the multi-touch or Disabled Disables this USB interface. the optional front USB interface. Enabled Enables this USB interface. Table 246: Advanced - USB configuration Panel PC 2100 user's manual V1.17...
Page 260: Sata Configuration
Option for configuring hot plugging for SATA in- Enabled Enables hot plugging for SATA interface 1. De- bility terface 1. vices can be connected/disconnected during operation. Disabled Disables hot plugging for SATA interface 1. Table 247: Advanced - SATA configuration Panel PC 2100 user's manual V1.17...
Page 261: Miscellaneous Configuration
Extended temperature Option for configuring the RAM refresh rate for Disabled Default RAM refresh rate. range the extended temperature range. Enabled Increases the RAM refresh rate. Table 248: Advanced - Miscellaneous configuration Panel PC 2100 user's manual V1.17...
Page 262: Thermal Configuration
63°C / 145°F, 71°C / 160°F, 79°C / 174°F, 85°C / 185°F, 87°C / 189°F, 90°C / 194°F, 95°C / 203°F, 103°C / 217°F Disabled Disables this function. Table 249: Advanced - Thermal configuration Panel PC 2100 user's manual V1.17...
Page 263: Security
Enabled Requires the user password to be entered when booting. Table 250: Security This setting can only be configured if a supervisor password has been set. Panel PC 2100 user's manual V1.17...
Page 264: Boot
Boot device priority Configures the boot order. Enter Opens this submenu "Boot device priority" on page 265. Boot configuration Configures the boot settings. Enter Opens this submenu "Boot configuration" on page 266. Table 251: Boot Panel PC 2100 user's manual V1.17...
Page 265: Boot Device Priority
The order is changed with "+" and USBHDD P0: "-". "Shift + 1" enables/disables a boot device. USBHDD P1: USBHDD P2: USBHDD P3: ATAPI CD: SATA HDD1: PCI LAN0: PCI LAN1: Internal shell Table 252: Boot - Boot device priority Panel PC 2100 user's manual V1.17...
Page 266: Boot Configuration
Enables this function. Setup via the serial interface using a terminal emulator (PuTTY or HyperTerminal). Information: This function is only possible with IF option 5ACCIF01.FPLS-000 or 5AC- CIF01.FPLS-001. Table 253: Boot - Boot configuration Panel PC 2100 user's manual V1.17...
Page 267 EFI boot services (approx. 130 MB more). Table 253: Boot - Boot configuration This setting is only possible if Console redirection is set to Enabled. This setting is only possible if Legacy boot is set to Enabled. Panel PC 2100 user's manual V1.17...
Page 268: Exit
(provided they have not yet been saved). Save changes Selecting this option saves any changes made Yes/No to CMOS after confirmation. Table 254: Exit Panel PC 2100 user's manual V1.17...
Page 269: Allocation Of Resources
○ ○ Table 257: IRQ interrupt assignments in PIC mode Advanced Configuration and Power Interface. Onboard resistive touch screen on Panel PC 2100. Monitor/Panel option, SDL/DVI transmitter, SDL3 transmitter If option 5ACCIF01.FPLS-000, 5ACCIF01.FPLS-001, COMA IF option ● ... Default setting ○...
Page 270: Interrupt Assignments In Apic Mode
PIRQ H ● Table 258: IRQ interrupt assignments in APIC mode Advanced Configuration and Power Interface. Onboard resistive touch screen on Panel PC 2100. Monitor/Panel option, SDL/DVI transmitter, SDL3 transmitter If option 5ACCIF01.FPLS-000, 5ACCIF01.FPLS-001, COMA IF option PIRQ A: For PCIe, PCI Express root port 0, VGA controller...
Page 271: Upgrade Information
This information is displayed on the following BIOS Setup screen: • After switching on the PC, BIOS Setup is accessed by pressing "F2". • From the "Advanced" menu in BIOS, select "OEM features". System BIOS MTCX firmware Figure 166: Software version Panel PC 2100 user's manual V1.17...
Page 272: Procedure In Efi Shell
4. After the EFI shell is booted, "startup.nsh" is executed and the BIOS upgrade is started. 5. The system must be rebooted after a successful upgrade. 6. Reboot and press "F2" to enter BIOS Setup and load the setup defaults; then select "Save changes and exit". Panel PC 2100 user's manual V1.17...
Page 273: Upgrading The Firmware On The Panel Pc 2100
Software 4.2.2 Upgrading the firmware on the Panel PC 2100 The "Firmware upgrade (MTCX)" software makes it possible to update the firmware depending on the PPC2100 system variant. The latest firmware upgrade is available in the Downloads section of the B&R website (www.br-automation.com).
Page 274: Multi-Touch Drivers
• Windows Embedded Standard 7 Premium • B&R Linux 8 and 9 No guarantee can be made regarding multi-touch or single-touch operation, compatibility and functionality when using other operating systems and/or individual touch screen drivers. Panel PC 2100 user's manual V1.17...
Page 275: Windows 10 Iot Enterprise 2016 Ltsb
The operating system contains all drivers necessary for operation. If an older version of the driver is still being used, the latest version can be downloaded from the B&R website (www.br-automation.com) and installed over it. Note that the Unified Write Filter (UWF) must be disabled for this. Panel PC 2100 user's manual V1.17...
Page 276: Activation
In accordance with Microsoft requirements, Windows 10 IoT Enterprise 2016 LTSB requires SVGA resolution (800 x 600) or higher in order to fully operate the Windows user interface (including system dialog boxes, apps, etc.). A lower resolution can be selected for applications. Panel PC 2100 user's manual V1.17...
Page 277: Windows 10 Iot Enterprise 2015 Ltsb
The operating system contains all drivers necessary for operation. If an older version of the driver is still being used, the latest version can be downloaded from the B&R website (www.br-automation.com) and installed over it. Note that the Unified Write Filter (UWF) must be disabled for this. Panel PC 2100 user's manual V1.17...
Page 278: Activation
(network, graphics, ADI, etc.) or optimized settings, nor is it activated! The product can be activated at a later time either over the phone or via the Internet (see "Activation"). Panel PC 2100 user's manual V1.17...
Page 279: Issues And Limitations
In accordance with Microsoft requirements, Windows 10 IoT Enterprise 2015 LTSB requires SVGA resolution (800 x 600) or higher in order to fully operate the Windows user interface (including system dialog boxes, apps, etc.). A lower resolution can be selected for applications. Panel PC 2100 user's manual V1.17...
Page 280: Windows Embedded 8.1 Industry Pro
Keyboard Filter Configurable Shell Launcher Configurable Toast Notification Filter Configurable USB filter Configurable ✓ Unified Write Filter Windows 8 Application Launcher Configurable Gesture filter Configurable Table 264: Device functions in Windows Embedded 8.1 Industry Pro Panel PC 2100 user's manual V1.17...
Page 281: Installation
Personalization is not possible, however (e.g. setting the desktop background). The product can be activated at a later time either over the phone or via the Internet. For instructions, see the Microsoft website. Panel PC 2100 user's manual V1.17...
Page 282: Contents Of The Recovery Dvd
In accordance with Microsoft requirements, Windows Embedded 8.1 Industry Pro requires XGA resolution (1024 x 768) or higher in order to fully operate the Windows user interface (including system dialog boxes, apps, etc.). A lower resolution can be selected for applications. Panel PC 2100 user's manual V1.17...
Page 283: Windows 7
Windows 7 Professional SP1 - 64-bit - English - DVD 5SWWI7.1300-MUL Windows 7 Ultimate SP1 - 32-bit - Multilingual - DVD 5SWWI7.1400-MUL Windows 7 Ultimate SP1 - 64-bit - Multilingual - DVD Table 265: 5SWWI7.1100-GER, 5SWWI7.1100-ENG, 5SWWI7.1200-GER, 5SWWI7.1200-ENG, 5SWWI7.1300-MUL, 5SWWI7.1400-MUL - Order data Panel PC 2100 user's manual V1.17...
Page 284: Overview
(graphics, network, etc.) are also installed in this process. 4.7.5 Drivers Current drivers for all approved operating systems are available in the Downloads section of the B&R website (www.br-automation.com). Information: Only download necessary drivers from the B&R website, not from vendor websites. Panel PC 2100 user's manual V1.17...
Page 285: Issues And Limitations
In accordance with Microsoft requirements, Windows 7 requires XGA resolution (1024 x 768) or higher in order to fully operate the Windows user interface (including system dialog boxes, etc.). A lower resolution can be selected for applications. Panel PC 2100 user's manual V1.17...
Page 286: Windows Embedded Standard 7
File-Based Write Filter (FBWF) Administrator accounts ✓ ✓ User accounts Configurable Configurable Windows Explorer shell ✓ ✓ Table 268: Device functions in Windows Embedded Standard 7 64-bit versions are not supported by all systems. Panel PC 2100 user's manual V1.17...
Page 287: Installation
In accordance with Microsoft requirements, Windows Embedded Standard 7 requires XGA resolution (1024 x 768) or higher in order to fully operate the Windows user interface (including system dialog boxes, etc.). A lower resolution can be selected for applications. Panel PC 2100 user's manual V1.17...
Page 288: Automation Runtime
BIOS setting Advanced - Graphics (IGD) configuration - IGD turbo to Disabled. Important: If BIOS setting Advanced - Graphics (IGD) configuration - IGD turbo is set to Disabled, the graphics performance of the system is noticeably reduced. Panel PC 2100 user's manual V1.17...
Page 289: Automation Runtime Embedded (Aremb)
Licensing with the Technology Guarding wizard is available in Automation Studio 4.1 and Automation Runtime 4.08 and later. Earlier versions of Automation Runtime do not require a Technology Guard. For more information about Technology Guarding, see Automation Help. Panel PC 2100 user's manual V1.17...
Page 290: B&R Hypervisor
B&R Hypervisor is completely independent of the version of the operating systems used. System requirements The following minimum software versions are required to operate B&R Hypervisor on the Panel PC 2100 : • ARemb upgrade AR F4.44 • Automation Studio V4.4 •...
Page 291: Mapp Technology
Motion provides uniform solutions for all areas of motion control: from in- dividual axes to multi-axis systems and even complex robotics and CNC appli- cations. Information: For details about mapp Technology, see the B&R website www.br-automation.com or Automation Help. Panel PC 2100 user's manual V1.17...
Page 292: B&R Linux 8 (Gnu/Linux)
Debian 8 can also be downloaded from the Debian website (http://www.debian.org). The Debian website also provides more detailed instructions. Notes regarding installation on B&R devices are included in a separate document that can be downloaded from the B&R website (www.br-automation.com). Panel PC 2100 user's manual V1.17...
Page 293: Drivers
Installation packages are also available on the B&R website (www.br-automation.com) for the necessary B&R modifications. 4.12.6 Drivers The operating system contains all drivers necessary for operation. The most current versions of B&R-specific drivers can be downloaded and installed from the B&R website (www.br- automation.com). Panel PC 2100 user's manual V1.17...
Page 294: B&R Linux 9 (Gnu/Linux)
Debian 9 can also be downloaded from the Debian website (http://www.debian.org). Corresponding instructions are also available on the Debian website. Notes regarding installation on B&R devices are included in a separate document that can be downloaded from the B&R website (www.br-automation.com). Panel PC 2100 user's manual V1.17...
Page 295: Drivers
4.13.6 Drivers Current drivers for all approved operating systems are available in the Downloads section of the B&R website (www.br-automation.com). Information: Only download necessary drivers from the B&R website, not from vendor websites. Panel PC 2100 user's manual V1.17...
Page 296: B&R Automation Device Interface (Adi) Control Center
• Reading operating hours (power-on hours) • Reading user settings and factory settings • Reading software versions • Updating and backing up BIOS and firmware • Creating reports about the current system (support assistance) Panel PC 2100 user's manual V1.17...
Page 297: Installation
The ADI driver is included in most B&R Windows operating systems; it can also be installed on demand. If a more current ADI driver version exists (see the Downloads section of the B&R website), it can be installed later. Note that the write filter must be disabled during installation. Panel PC 2100 user's manual V1.17...
Page 298: B&R Automation Device Interface (Adi) Development Kit
For a detailed description of how to use ADI functions, see Automation Help. The B&R Automation Device Interface (ADI) Development Kit can be downloaded at no cost from the Downloads section of the B&R website (www.br-automation.com). Panel PC 2100 user's manual V1.17...
Page 299: B&R Automation Device Interface (Adi) .Net Sdk
B&R. For a detailed description of how to use ADI functions, see Automation Help. The ADI .NET SDK can be downloaded at no cost from the Downloads section of the B&R website (www.br- automation.com). Panel PC 2100 user's manual V1.17...
Page 300: B&R Key Editor
For a detailed guide on configuring keys and LEDs as well as installing the key configuration on the target system, see the help documentation for the B&R Key Editor. The B&R Key Editor and its help documentation can be downloaded at no cost from the Downloads section of the B&R website (www.br-automation.com). Panel PC 2100 user's manual V1.17...
Page 301: B&R Kcf Editor
Additional features if the B&R KCF Editor is executed on the target device • Panel and key detection • LED test • Configuration uploads/downloads The ADI driver must be installed on the B&R PC to use these features. Panel PC 2100 user's manual V1.17...
Page 302: Hmi Service Center
- For APC810/PPC800 - For APC910/PPC900 - For APC2100/PPC2100 - For APC2200/PPC2200 - For APC3100/ PPC3100 - For APC51x/PP500 - For Automation Panel 800/900 - For Automation Panel 1000/5000 Table 272: 5SWUTI.0001-000 - Order data Panel PC 2100 user's manual V1.17...
Page 303: Standards And Certifications
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission stan- dard for industrial environments Information: Declarations of conformity are available on the B&R website under Downloads - Certificates - Decla- rations of conformity. Panel PC 2100 user's manual V1.17...
Page 304: Certifications
Russian Federation (based on EU compliance). 5.2.3 EAC Products with this mark are tested by an accredited testing laboratory and permitted for import to the Eurasian Economic Union (based on EU compliance). Panel PC 2100 user's manual V1.17...
Page 305: Rcm
- Landscape format - For PPC900 / PPC2100 / PPC3100 / link modules 5PPC2100.BY44-000 Panel PC 2100 - Intel Atom E3845 1.91 GHz - Quad core - 4 GB SDRAM - For Automation Panel 923/933 5PPC2100.BY48-000 PPC2100 system unit - Intel Atom E3845 1.91 GHz - Quad core - 8 GB SDRAM - For Automation Panel 923/933/1000 5CFAST.2048-00...
Page 306: Ul Haz. Loc. Certification
Devices must remain voltage-free until installation work is complete. The tightening torque for the power supply terminals is 0.5 Nm. Cables must be able to handle a surface temperature of 75°C. PPC2100 systems with AP923 or AP1000 panels are only permitted to be operated with 24 VDC. Panel PC 2100 user's manual V1.17...
Page 307: Operation
Danger! Failure to follow these instructions can result in death, serious injury or damage to property! Danger ! Le non-respect de ces instructions peut entraîner des blessures graves ou mortelles! Panel PC 2100 user's manual V1.17...
Page 308: Usb Connection With The Panel Pc 2100
Standards and certifications 5.2.7.5 USB connection with the Panel PC 2100 5.2.7.5.1 Introduction The information below describes the use of USB peripheral devices on USB interfaces 1 and 2 of the B&R Panel PC 2100 in Hazardous Locations Class I, Division 2, Groups A, B, C and D.
Page 309 This B&R device is suitable for use in Class I, Division 2, Groups A, B, C and D. In addition, it offers nonincendive field wiring for devices in Class I, Division 2, Groups A, B, C and D. Panel PC 2100 user's manual V1.17...
Page 310: Usb Connection With The Automation Panel 1000
Front USB interface (USB 2.0): No-load voltage [V 5.04 V Short circuit current [I 1170 mA Associated capacitance [C 20 μF Associated inductance [L 16.8 μH Table 276: Nonincendive electrical circuit parameters for the front USB interface Panel PC 2100 user's manual V1.17...
Page 311 This B&R device is suitable for use in Class I, Division 2, Groups A, B, C and D. In addition, it offers nonincendive field wiring for devices in Class I, Division 2, Groups A, B, C and D. Panel PC 2100 user's manual V1.17...
Page 312: Usb Connection With The 4-Port Hub
USB interfaces (USB 2.0): No-load voltage [V 5.11 V Short circuit current [I 1621 mA Associated capacitance [C 20 μF Associated inductance [L 16.8 μH Table 278: Nonincendive electrical circuit parameters for the 4-port USB interfaces Panel PC 2100 user's manual V1.17...
Page 313 This B&R device is suitable for use in Class I, Division 2, Groups A, B, C and D. In addition, it offers nonincendive field wiring for devices in Class I, Division 2, Groups A, B, C and D. Panel PC 2100 user's manual V1.17...
Page 314: Accessories
Number of pins 3 (female) Type of terminal block Screw clamp terminal block Cage clamp terminal block Cable type Only copper wires (no aluminum wires!) Spacing 5.08 mm Table 281: 0TB103.9, 0TB103.91 - Technical data Panel PC 2100 user's manual V1.17...
Page 315 Yes, although applies only if all components installed in the complete system have this certification and are listed on the associated DNV GL certificate for the product family. Cage clamp terminal blocks cannot be used side-by-side. The respective limit data for the I/O modules must be taken into account. Panel PC 2100 user's manual V1.17...
Page 316: Terminal Block If Options
Yes, although applies only if all components installed in the complete system have this certification and are listed on the associated DNV GL certificate for the product family. The limit data for each I/O module must be taken into consideration. Panel PC 2100 user's manual V1.17...
Page 317: Usb Flash Drives
Full speed max. 0.9 MB/s, High speed max. 23 MB/s Endurance SLC flash Data retention >10 years Data reliability <1 unrecoverable error per 10 bits read Connection cycles >1500 Table 285: 5MMUSB.2048-01, 5MMUSB.4096-01 - Technical data Panel PC 2100 user's manual V1.17...
Page 318 8.35 mm Table 285: 5MMUSB.2048-01, 5MMUSB.4096-01 - Technical data Indicates data transfer (receiving and transmitting). The maximum ambient temperature is typically derated by 1°C per 1000 meters starting at 500 meters above sea level. Panel PC 2100 user's manual V1.17...
Page 319: Temperature/Humidity Diagram
Accessories 6.3.1.4 Temperature/Humidity diagram Storage Operation Transport Temperature [°C] Figure 172: 5MMUSB.xxxx-01 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 320: 5Mmusb.032G-02
Max. 67 mA in sleep mode, max. 122 mA read, max. 141 mA write Environmental conditions Temperature Operation 0 to 70°C Storage -55 to 95°C Transport -55 to 95°C Table 287: 5MMUSB.032G-02 - Technical data Panel PC 2100 user's manual V1.17...
Page 321: Temperature/Humidity Diagram
Indicates data transfer (receiving and transmitting). The maximum ambient temperature is typically derated by 1°C per 1000 meters starting at 500 meters above sea level. 6.3.2.4 Temperature/Humidity diagram Storage Operation Transport Temperature [°C] Figure 173: 5MMUSB.032G-02 - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 322: Usb Hub
• 4x USB 2.0, interfaces • Compatible with the APC2100 and PPC2100 Installation on the Panel PC 2100 is possible with display diagonals ≥10.1". The USB hub can be installed starting with the following revisions: • 5PPC2100.BY01-000 - Rev. F0 and later •...
Page 323 B&R cannot guarantee their functionality. Functionality is ensured when using the USB devices available from B&R. Caution! Because this interface is designed according to general PC specifications, extreme care should be taken with regard to EMC, wiring, etc. Panel PC 2100 user's manual V1.17...
Page 324: Dimensions
The USB interface is protected by a maintenance-free "USB current-limiting switch" (max. 1 A). Information: If a Technology Guard (USB dongle) is used, it is recommended to connect it to the USB HUB 3 inter- face. 6.4.1.4 Dimensions 47.5 Figure 174: 5ACCUSB4.0000-000 - Dimensions Panel PC 2100 user's manual V1.17...
Page 325: Servicing And Maintenance
Apply the cleaning agent to the cloth beforehand; do not spray it directly on the device! Never use aggressive solvents, chemicals, scouring agents, pressurized air or steam-jet air ejectors. Information: Displays with a touch screen should be cleaned at regular intervals. Panel PC 2100 user's manual V1.17...
Page 326: Tips For Extending The Service Life Of The Display
• Using complementary colors in consecutive images • Using screensavers 7.3 Pixel errors Information: Displays may contain defective pixels (pixel errors) that result from the manufacturing process. They are not grounds for initiating a complaint or warranty claim. Panel PC 2100 user's manual V1.17...
Page 327: Replacing A Cfast Card
Therefore, do not attempt to perform repairs yourself. Repairs are only permitted to be performed by authorized qualified personnel at the place of manufacture. To process a repair/complaint, please create a repair order or complaint using the B&R Material Return Portal on the B&R website at www.br-automation.com. Panel PC 2100 user's manual V1.17...
Page 328: Maintenance Controller Extended (Mtcx)
The functions of the MTCX can be extended by upgrading its firmware . The version can be read in BIOS or with the B&R Control Center in approved Microsoft Windows operating systems. Can be downloaded from the Downloads section of the B&R website (www.br-automation.com). Panel PC 2100 user's manual V1.17...
Page 329: Abbreviations
Table 291: Abbreviations used in this user's manual A.3 Viewing angles For the viewing angle values of display types (R, L, U, D), see the technical data of the individual components. 6 o'clock direction Panel PC 2100 user's manual V1.17...
Page 330: Chemical Resistance
Figure 176: Single-touch display unit with Autotex panel overlay (sample screenshot) AP9x3 single-touch panels <revision B8 were manufactured with the aluminum panel overlay. Coated front Touch screen Panel overlay (frame) Figure 177: Single-touch display unit with aluminum panel overlay (sample screenshot) Panel PC 2100 user's manual V1.17...
Page 331 Appendix A AP9x3 and AP1000 multi-touch panels feature an edge-to-edge glass surface. Coated front Touch screen (frame) Figure 178: Multi-touch panel with glass surface (sample screenshot) Panel PC 2100 user's manual V1.17...
Page 332: Autotex Panel Overlay (Polyester)
• Sodium bisulphate • Xylene • Diesel • Sodium carbonate The panel overlay is resistant to exposure to glacial acetic acid for less than one hour without visible damage per DIN 42115 Part 2. Panel PC 2100 user's manual V1.17...
Page 333: Aluminum Panel Overlay
• Coolant <4% • Sidolin • Diesel • Sodium hydroxide <40% • Skydrol • Acetic acid <50% • Petroleum The coated aluminum front is not resistant to the following chemicals: • Acetone • Ethyl acetate Panel PC 2100 user's manual V1.17...
Page 334: Touch Screen
• Brake fluid • Lysol • Water • Hydrogen chloride <6% • Methylbenzene • White wine vinegar • Coca-Cola • Methyl ethyl ketone • Windex Original • Dimethylbenzene • Naphtha • Ethanol • Nitric acid <70% Panel PC 2100 user's manual V1.17...
Page 335: Touch Screen
Table 292: 5-wire AMT touch screen - Technical data A.5.1.2 Temperature/Humidity diagram All values apply to non-condensing operation. Operation -80 -70 -60 -50 -40 -30 -20 -10 40 50 Temperature [°C] Figure 179: 5-wire AMT touch screen - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 336: Touch Screen (Multi-Touch Generation 2)
90% at max. 35°C Operating conditions Activation Finger, thin glove, 3M Smart Pen Table 293: 3M touch screen - Technical data A.5.2.3 Temperature/Humidity diagram Operation Temperature [°C] Figure 180: 3M touch screen - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 337: Touch Screen (Multi-Touch Generation 3)
Up to 90% at max. 35°C, for >35°C see diagram Transport Up to 90% at max. 35°C, for >35°C see diagram Operating conditions Activation Finger, thin glove, 3M Smart Pen Table 294: 3M touch screen - Technical data Panel PC 2100 user's manual V1.17...
Page 338: Temperature/Humidity Diagram
Appendix A A.5.3.3 Temperature/Humidity diagram All values apply to non-condensing operation/storage/transport. Operation Temperature [°C] Figure 181: 3M touch screen - Temperature/Humidity diagram Panel PC 2100 user's manual V1.17...
Page 339 Panel PC 2100 with AP9x3 panels (sample figure) - Installation diagram......26 Figure 6: Panel PC 2100 with AP1000 panels with retaining clips (sample figure) - Installation diagram 27 Figure 7: Panel PC 2100 with AP1000 panels with clamping blocks (example figure) - Installation dia- gram............................
Page 340 5CFAST.032G-10 ≤Rev. F0, 5CFAST.064G-10 ≤Rev. D0, 5CFAST.128G-10 ≤Rev. D0 - Tem- perature/Humidity diagram....................156 Figure 109: CFast card - Write protection....................157 Figure 110: RS232/422/485 interface - COMA operation in RS485 mode..........202 Figure 111: RS232/422/485 interface - COMD operation in RS485 mode..........203 Panel PC 2100 user's manual V1.17...
Page 341 Boot - Boot configuration......................266 Figure 164: Exit............................268 Figure 165: PCIe routing with enabled APIC..................270 Figure 166: Software version........................271 Figure 167: ADI Control Center screenshots - Examples............... 296 Figure 168: ADI Development Kit Screenshots (Symbolbild)..............298 Panel PC 2100 user's manual V1.17...
Page 342 Multi-touch panel with glass surface (sample screenshot)..........331 Figure 179: 5-wire AMT touch screen - Temperature/Humidity diagram..........335 Figure 180: 3M touch screen - Temperature/Humidity diagram..............336 Figure 181: 3M touch screen - Temperature/Humidity diagram..............338 Panel PC 2100 user's manual V1.17...
Page 343 5AP923.1505-00 - Technical data....................75 Table 54: 5AP923.1906-00 - Order data..................... 77 Table 55: 5AP923.1906-00, 5AP923.1906-00 - Technical data..............77 Table 56: 5AP933.156B-00 - Order data.....................80 Table 57: 5AP933.156B-00, 5AP933.156B-00 - Technical data..............80 Panel PC 2100 user's manual V1.17...
Page 344 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10, 5CFAST.256G-10 - Order data..152 Table 109: 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10 - Order data........152 Table 110: 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10, 5CFAST.256G-10 - Technical data.. 152 Table 111: 5CFAST.032G-10, 5CFAST.064G-10, 5CFAST.128G-10 - Technical data........154 Panel PC 2100 user's manual V1.17...
Page 345 Table 164: 5ACCIF01.FPLS-001 - Order data.................... 183 Table 165: 5ACCIF01.FPLS-001 - Technical data..................183 Table 166: 5ACCIF01.FPLS-001 - POWERLINK interface................. 184 Table 167: 5ACCIF01.FPLS-001 - Interface COMA..................184 Table 168: 5ACCIF01.FPLS-001 - LED status indicators................185 Panel PC 2100 user's manual V1.17...
Page 346 Terminating resistor........................208 Table 220: 5ACCIF01.ICAN-000 - LED status indicator................208 Table 221: BIOS-relevant keys for POST....................235 Table 222: BIOS-relevant keys........................235 Table 223: Main............................236 Table 224: Main - System information......................237 Table 225: Advanced............................238 Panel PC 2100 user's manual V1.17...
Page 347 Connected nonincendive device with field wiring..............311 Table 278: Nonincendive electrical circuit parameters for the 4-port USB interfaces......... 312 Table 279: Connected nonincendive device with field wiring..............313 Table 280: 0TB103.9, 0TB103.91 - Order data...................314 Panel PC 2100 user's manual V1.17...
Page 348 Table 291: Abbreviations used in this user's manual.................. 329 Table 292: 5-wire AMT touch screen - Technical data................335 Table 293: 3M touch screen - Technical data.....................336 Table 294: 3M touch screen - Technical data.....................337 Panel PC 2100 user's manual V1.17...
Page 349 5CFAST.016G-00..............................149 5CFAST.032G-00..............................149 5CFAST.032G-10..............................152 5CFAST.064G-10..............................152 5CFAST.128G-10..............................152 5CFAST.2048-00..............................149 5CFAST.256G-10..............................152 5CFAST.4096-00..............................149 5CFAST.8192-00..............................149 5MMUSB.032G-02............................... 320 5MMUSB.2048-01..............................317 5MMUSB.4096-01..............................317 5PPC2100.BY01-000............................144 5PPC2100.BY11-000............................144 5PPC2100.BY22-000............................144 5PPC2100.BY34-000............................144 5PPC2100.BY44-000............................144 Panel PC 2100 user's manual V1.17...
Page 350 Model number index 5PPC2100.BY48-000............................144 5SWLIN.0543-MUL.............................. 292 5SWLIN.0643-MUL.............................. 292 5SWLIN.0743-MUL.............................. 294 5SWUTI.0001-000..............................302 5SWW10.0243-MUL............................277 5SWW10.0543-MUL............................275 5SWWI7.1100-ENG..............................283 5SWWI7.1100-GER..............................283 5SWWI7.1200-ENG............................. 283 5SWWI7.1200-GER............................. 283 5SWWI7.1300-MUL..............................283 5SWWI7.1400-MUL..............................283 5SWWI7.1543-ENG............................. 286 5SWWI7.1643-ENG............................. 286 5SWWI7.1743-MUL..............................286 5SWWI7.1843-MUL..............................286 5SWWI8.0343-MUL..............................280 5SWWI8.0443-MUL..............................280 Panel PC 2100 user's manual V1.17...
Page 351 Statistical values........................... 243, 246, 250 Super I/O configuration..........................241 System board features..........................242 System information............................237 Temperature values..........................244, 247 Thermal configuration............................ 262 USB configuration............................259 BIOS default settings............................235 BIOS Setup keys..............................235 Panel PC 2100 user's manual V1.17...
Page 352 Dimensions..........................23, 24, 25, 23, 24, 25 Dimension standards............................16 Display brightness.............................. 232 Disposal................................15, 15 DNV GL certification............................305 Dongle................................. 289 Dynamic wear leveling............................147 EAC..................................304 Electrical characteristics............................42 Block diagram..............................45 Panel PC 2100 user's manual V1.17...
Page 353 Guidelines................................16 HMI Service Center............................302 Humidity................................40 I/O address assignments............................ 269 IF1, IFx slot................................56 IF option................................158 IF option slot................................. 56 Image persistence.............................. 326 Immunity to interference............................. 222 Individual components..........................218, 218 Panel PC 2100 user's manual V1.17...
Page 354 Minimum ambient temperature for worst-case operation................34, 34 Mounting an Automation Panel 1000 with clamping blocks................216 Mounting an Automation Panel 1000 with retaining clips.................. 214 Mounting compatibility............................63 Mounting orientations............................. 30, 30 MTCX.................................. 328 MTCX Development Kit............................229 Panel PC 2100 user's manual V1.17...
Page 355 Recovery DVD..............................282 Relative humidity..............................40 Repairs................................327 Replacement parts.............................. 327 Replacing a CFast card............................. 327 Replacing the system unit..........................219 Reset button................................. 54 RS232 interface............................178, 188 RS422 Bus length..............................204 Cable type..............................204 Panel PC 2100 user's manual V1.17...
Page 356 Touch screen..............................335 Touch screen calibration............................. 230 Type 4X indoor use only............................41 UL 50..................................41 UL certification..............................304 UL Haz. Loc. certification........................... 306 Universal Serial Bus 2.0............................. 323 Universal Serial Bus 3.0............................52 Panel PC 2100 user's manual V1.17...
Page 357 Windows 10 IoT Enterprise 2015 LTSB......................277 Windows 7..............................283, 283 Windows Embedded 8.1 Industry Pro....................... 280 Windows Embedded Standard 7........................286 Wiring.................................. 221 X2X Link master - IFx..........................163, 197 X2X Link master interface.......................... 163, 197 Panel PC 2100 user's manual V1.17...

This manual is also suitable for:

Mappc2100-eng

B&R Panel PC 2100 User Manual

Quick Links

Related Manuals for B&R Panel PC 2100

Summary of Contents for B&R Panel PC 2100