YOKOGAWA UT Advanced UT32A User Manual page 18

9.3 Forcing SP to Track PV (PV Tracking) ............................................................................. 9-4
9.4 Forcing SP to Track Remote Input (SP Tracking) ............................................................. 9-5
9.5 Setting Controller Action at Power ON (Restart Mode) .................................................... 9-6
9.6 Setting Time between Powering on Controller and Starting Control (Restart Timer) ....... 9-7
Chapter 10 Output (Control and Retransmission) Functions
10.1 Setting Control Output Type ........................................................................................... 10-1
10.2 Setting Control Output Cycle Time ................................................................................. 10-5
10.3 Setting Limiter to Control Output .................................................................................... 10-6
10.4 Disabling Output Limiter in MAN mode .......................................................................... 10-7
10.5 Setting Velocity Limiter to Control Output ....................................................................... 10-8
10.6 Reducing 4-20 mA Current Output to 0 mA (Tight Shut Function) ................................. 10-9
10.7 Setting ON/OFF Control Hysteresis ............................................................................. 10-10
10.8 Canceling Offset of PV and SP (Manual Reset) ........................................................... 10-12
10.9 Setting Hysteresis and Dead Band for Heating/cooling Control Output ....................... 10-13
10.10 Setting Hysteresis and Dead Band for Position Proportional Control Output ............... 10-15
10.11 Setting Retransmission Output Terminal, Type, and Scales ......................................... 10-16
10.12 Setting Preset Output Value ......................................................................................... 10-18
10.12.1 Setting Output Value in STOP Mode (Preset Output) ..................................... 10-18
10.12.2 Setting Output Value When Switched to MAN Mode (Manual Preset Output) ... 10-20
10.12.3 Setting Output Value When Error Occurs (Input Error Preset Output)............ 10-21
10.13 Changing Current Output Range .................................................................................. 10-22
10.14 Adjusting Motor-operated Valve Position (Position Proportional Output) ..................... 10-23
10.14.1 Setting Valve Operation Mode ........................................................................ 10-24
10.14.2 Adjusting Valve Position Automatically ........................................................... 10-24
10.14.3 Adjusting Valve Position Manually .................................................................. 10-25
10.14.4 Setting Valve Traveling Time (Estimating Type) .............................................. 10-26
10.14.5 Selecting Feedback Input (Resistor/Current) .................................................. 10-26
10.15 Using 15 V DC Loop Power Supply ............................................................................. 10-27
Chapter 11 Alarm Functions
11.1 Setting Alarm Type ..........................................................................................................11-1
11.2 Setting Number of Alarm Groups to Use .......................................................................11-13
11.3 Setting Hysteresis to Alarm Operation ..........................................................................11-14
11.4 Delaying Alarm Output (Alarm Delay Timer) .................................................................11-15
11.5 Setting Alarm Output to Control Relay Terminal ............................................................11-16
11.6 Setting Alarm Action According to Operation Mode .......................................................11-17
11.7 Setting Heater Break Alarm ...........................................................................................11-18
Chapter 12 Contact Input/Output Functions
12.1 Setting Contact Input Function ....................................................................................... 12-1
12.1.1 Setting Contact Input Function ......................................................................... 12-1
12.1.2 Changing Contact Type of Contact Input .......................................................... 12-9
12.2 Setting Contact Output Function .................................................................................. 12-10
12.2.1 Setting Function of Contact Output ................................................................. 12-10
12.2.2 Changing Contact Type of Contact Output ..................................................... 12-14
Chapter 13 Display, Key, and Security Functions
13.1 Setting Display Functions ............................................................................................... 13-1
13.1.1 Setting Active Color PV Display Function ......................................................... 13-1
13.1.2 Masking Arbitrary Display Value in Operation Display ...................................... 13-4
13.1.3 Registering SELECT Display (Up to 5 Displays) .............................................. 13-5
13.1.4 Changing Event Display ................................................................................... 13-6
IM 05P01D31-01EN
Contents
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
App
Index
xv