TRENDnet TI-PG1284i User Manual page 119

TRENDnet User's Guide
L3 ipv6 address
interface <IPv6_ADDR>/M
L3 no ipv4 address
interface A.B.C.D/M
L3 no ipv4 address
interface <IPv6_ADDR>/M
L3 ipv4 route A.B.C.D/M
interface A.B.C.D
L3 ipv6 route
interface <IPv6_ADDR>/M
<IPv6_ADDR>
L3 no ipv4 route
interface A.B.C.D/M A.B.C.D
© Copyright 2016 TRENDnet. All Rights Reserved.
We can assign multiple IPv4 interface route to
a single interface with different IP segment.
If this configuration is a first IP assigning to the
interface then automatically interface is
enabled for routing.
This command assigns a specified IPv6
interface route to the interface.
We can assign only one IPv6 interface route for
an interface vlan.
If this configuration is a first IP assigning to the
interface then it automatically enables the
interface with routing.
This command deletes a specified IPv4
interface route from the interface vlan.
This command deletes all dependent static
routes on the specified IPv4 interface route.
If there is no assigned IP addresses for the
specified interface after deleting then it will
automatically disables routing in interface.
This command deletes a specified IPv6
interface route from the interface.
This command deletes all dependent static
routes on the specified IPv6 interface route.
If there is no assigned IP addresses for the
specified interface after deleting then it will
automatically disables routing in interface vlan.
This command configures an IPv4 static route
onto the specified interface vlan.
This command configures an IPv6 static route
onto the specified interface vlan.
This command deletes a specified IPv4 static
route from an interface vlan.
L3 no ipv6 route
interface <IPv6_ADDR>/M
<IPv6_ADDR>
Example:

IP Forwarding Enable: This command is used to enable ip forwarding (routing).
TI-PG1284I(config)#ip forwarding enable

IP Forwarding Disable: This command is used to disable ip forwarding.
TI-PG1284I(config)#no ip forwarding enable

ARP proxy enable: This command is used to enable ARP proxy.
TI-PG1284I(config)#ip arp proxy enable

ARP proxy disable: This command is used to disable ARP proxy.
TI-PG1284I(config)#no ip arp proxy enable

Add a static IPv4/IPv6 ARP entry: This command is used to add a static IPv4/IPv6
ARP entries.
TI-PG1284I(config)#ipv4 arp 192.168.20.1 00:11:22:33:44:55
TI-PG1284I(config)#ipv6 arp 1234:ab::ccdd 00:11:22:33:44:55

Deletes a static IPv4/IPv6 ARP entry: This command is used to delete static IPv4/IPv6
ARP entries
TI-PG1284I(config)#no ipv4 arp 192.168.20.1 00:11:22:33:44:55
TI-PG1284I(config)#no ipv6 arp 1234:ab::ccdd 00:11:22:33:44:55

Assigning a IPv4/IPv6 interface router: This command is used to add an IPv4/IPv6
interface route to a interface vlan.
TI-PG1284I(config)#interface vlan 1
TI-PG1284I(config-if-vlan-l3)#
TI-PG1284I(config-if-vlan-l3)#ipv4 address 192.168.20.1/24
TI-PG1284I(config-if-vlan-l3)#ipv6 address 1234:ab::ccdd/120
TI-PG1284i
This command deletes a specified IPv6 static
route from an interface vlan.
116