1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Switch
  5. TI-RP262i
  6. User manual

TRENDnet TI-RP262i User Manual

Managed industrial l2
Hide thumbs Also See for TI-RP262i:
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for TRENDnet TI-RP262i

Summary of Contents for TRENDnet TI-RP262i

  • Page 2: Table Of Contents

    Loop Detection ......................80 General Settings ......................28 Modbus ........................82 System ....................... 28 Power over Ethernet ....................86 Jumbo Frame ..................... 29 STP ..........................91 SNTP ........................30 Management Host ..................... 32 Security ..................100 © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 3 TI-G160i ........................160 SFP Information ......................123 Troubleshooting ................. 163 Traffic Monitor ......................124 Appendix ..................164 Management ................126 SNMP ......................... 126 SNMP Trap ....................... 128 Auto Provision ......................129 Mail Alarm ......................... 130 © Copyright 2020 TRENDnet. All Rights Reserved.

  • Page 4: Product Overview

    VLANs for segmenting and isolating virtual LAN groups, QoS to prioritize traffic, port bandwidth controls, SNMP monitoring, and more, making each TRENDnet industrial layer 2 rackmount switch a powerful solution for SMB networks. Package Contents In addition to your switch, the package includes: •...
  • Page 5 Note: For any unused ports or SFP slots, it is recommended to leave the rubber plugs Power Terminals – Using proper gauge wire, terminate the leads from your installed during operation. power supply to these power terminals to power your switch. © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 6 Supports an output with current carrying capacity of 1A @ 24V DC. *Please note power supply is sold separately* **Supported power supplies: TI-S12024 (120W), TI-S24048 (240W), TI-S48048 (480W). Lower wattage power supplies may be used but may result in decreased PoE power budget** © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 7 DIP No Name State Status Primary power input source alarm trigger enabled. Primary power input source alarm trigger disabled. Redundant power input source alarm trigger enabled. Redundant power input source alarm trigger disabled. © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 8 Reset Button – Push the button for 5-10 seconds and release to reset. • Grounding point/screw – The switch chassis can also be connected to a known ground point for additional safety and protection. (grounding wire not included) © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 9 Supports an output with current carrying capacity of 1A @ 24V DC. **Supported power supplies: TI-S12024 (120W), TI-S24048 (240W), TI-S48048 (480W). Lower wattage power supplies may be used but may result in decreased PoE power budget** © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 10 Port 9 SFP set to Gigabit speed full duplex Port 9 SFP set to 100Mbps speed full duplex Port 10 SFP set to Gigabit speed full duplex Port 10 SFP set to 100Mbps speed full duplex © Copyright 2020 TRENDnet. All Rights Reserved.

  • Page 11: Non-Poe

    Reset Button – Push the button for 3 seconds and release to reset to factory defaults. • Grounding point/screw – The switch chassis can also be connected to a known ground point for additional safety and protection. (grounding wire not included) © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 12 Device supports overload current protection and reverse polarity protection. ALM Output Connects external alarm and sends output signal if fault is detected based on DIP switch settings. Supports an output with current carrying capacity of 1A @ 24V DC. © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 13 Managed Industrial L2 Switches TRENDnet User’s Guide ALM DIP Switches © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 14 Reset Button – Push the button for 3 seconds and release to reset to factory defaults. • Grounding point/screw – The switch chassis can also be connected to a known ground point for additional safety and protection. (grounding wire not included) © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 15 Device supports overload current protection and reverse polarity protection. ALM Output Connects external alarm and sends output signal if fault is detected based on DIP switch settings. Supports an output with current carrying capacity of 1A @ 24V DC. © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 16 Managed Industrial L2 Switches TRENDnet User’s Guide ALM DIP Switches © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 17 Reset Button – Push the button for 3 seconds and release to reset to factory defaults. • Grounding point/screw – The switch chassis can also be connected to a known ground point for additional safety and protection. (grounding wire not included) © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 18 Device supports overload current protection and reverse polarity protection. ALM Output Connects external alarm and sends output signal if fault is detected based on DIP switch settings. Supports an output with current carrying capacity of 1A @ 24V DC. © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 19 Managed Industrial L2 Switches TRENDnet User’s Guide ALM DIP Switches © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 20 Reset Button – Push the button for 3 seconds and release to reset to factory defaults. • Grounding point/screw – The switch chassis can also be connected to a known ground point for additional safety and protection. (grounding wire not included) © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 21 Device supports overload current protection and reverse polarity protection. ALM Output Connects external alarm and sends output signal if fault is detected based on DIP switch settings. Supports an output with current carrying capacity of 1A @ 24V DC. © Copyright 2020 TRENDnet. All Rights Reserved.
  • Page 22 Managed Industrial L2 Switches TRENDnet User’s Guide ALM DIP Switches © Copyright 2020 TRENDnet. All Rights Reserved.

  • Page 23: Din-Rail Installation

    To unmount the switch from the DIN-Rail, slightly pull the switch downwards to clear the bottom of the DIN-Rail and rotate away from DIN-Rail to unmount. The movable clip at the top of the DIN-Rail bracket should be on top. © Copyright 2020 TRENDnet. All Rights Reserved.

  • Page 24: Install Power Supply Connections

    TRENDnet User’s Guide Install power supply connections SFP Transceiver/Optical Cable Installation Connect the power supply (sold separate, e.g. TRENDnet TI-S24048) to the switch terminal block as shown below. Remove the rubber plug from the SFP slot. Optional: The switch chassis can also be connected to a known ground point for Note: For any unused ports or SFP slots, it is recommended to leave the additional safety and protection (grounding wire not included).

  • Page 25: Basic Ip Configuration

    User Name: admin Password: admin Note: User name and password are case sensitive. 8. When confirmation message appears click OK. Note: Once the settings are saved, you can connect the switch to your network. © Copyright 2020 TRENDnet. All Rights Reserved.

  • Page 26: Connect Additional Devices To Your Switch

    Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your computer or device network settings (also called TCP/IP settings) are configured properly within the network subnet your switch is connected. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 27: Accessing Switch Management Interfaces

    Console User Name: admin vlan show This command displays the current VLAN Note: User Name and Password are case sensitive. configurations. Enable Mode/Privileged Exec User Name: admin Enable Mode/Privileged Exec Password: admin © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 28 In Configure code, executing command “interface fastethernet1/0/5” enter the interface port 5 node. Note: depend on your port speed, gigaethernet1/0/5 for gigabit Ethernet ports and fastethernet1/0/5 for fast Ethernet ports. [DEVICE_NAME](config)#interface gigaethernet1/0/5 [DEVICE_NAME](config-if)# © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 29: Access Your Switch Web Management Page

    2. Enter the user name and password. By default: User Name: admin Password: admin Note: User Name and Password are case sensitive. Parameter Description User Name Enter the user name. Password Enter the password. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 30 This field displays the total memory the Switch has and the Memory memory which is currently available (Free) and occupied Information (Usage). This field displays current date (yyyy-mm-dd) and time Current Time (hh:mm:ss). Refresh Click this to update the information in this screen. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 31 To configure a static IP address and a gateway for the Switch. configure interface eth0 This command enters the eth0 interface [DEVICE_NAME](config-if)#ip address 192.168.202.111/24 node to configure the system IP. [DEVICE_NAME](config-if)#ip address default-gateway 192.168.202.1 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 32 The bigger the frame size, the better the performance. Apply Click this button to take effect the settings. Refresh Click this button to reset the fields to the last setting. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 33 (first | second | the Daylight Saving Time. Time Server Configuration: third | fourth | last) (Sunday For Example: first Sunday 4 0 (AM:0 1st ----------------------------------------------- | Monday | Tuesday | Sunday in April) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 34 This field displays the date you open / refresh this menu. [DEVICE_NAME](config)#time daylight-saving-time end-date last Saturday 10 0 Time and Date Setting Select this option if you want to enter the system date and time Manual manually. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 35 The command displays the all of the interface is one hour ahead of GMT or UTC (GMT+1). eth0 configurations. eth0 show The command displays the all of the interface eth0 configurations. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 36 Basic Settings > General Settings > Management Host Parameter Description Management This field configures the management host. Host Apply Click this button to take effect the settings. Refresh Click this button to begin configuring this screen afresh. Management Host List © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 37 This command configures a static unicast static MACADDR vlan entry. VLANID port PORT_ID configure no mac-address-table This command removes a static unicast entry © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 38 Switch’s MAC addresses itself. Click Delete to remove this manually entered MAC address entry Action from the MAC address table. You cannot delete the Switch’s MAC address from the static MAC address table. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 39 It displays CPU if it is the entry for the Switch itself. Port The CPU means that it is the Switch’s MAC. Total Counts This field displays the total entries in the MAC table. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 40 Default Settings Mirror Configurations: State : Disable Monitor port : 1 Ingress port(s) : None Egress port(s) : None © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 41 Use this field only if you want to make some settings the same All Ports for all ports. Use this field first to set the common settings and then make adjustments on a port-by-port basis. Source Port This field displays the number of a port. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 42 A loopback test is a test in which a signal in sent from a communications device and returned (looped back) to it as a way to determine whether the device is working right or © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 43 Ethernet cable and shows the broken distance. interface clean cable-test result This command cleans the test result of the Ethernet cable test. interface show cable-test result This command displays the test result of the Ethernet cable test. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 44 This field displays the link status of the port. If the port is up, it displays the port’s speed, duplex and flow control setting. Link Status Otherwise, it displays Link Down if the port is disabled or not connected to any device. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 45 The field displays the detail port status if the port is blocked by Status some protocol. Uptime The sustained time from last link up. Medium Mode The current working medium mode, copper or fiber, for the port. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 46 7, to the lowest priority queue, 0. Each hardware queue will transmit all of the 42-1496 packets in its buffer before permitting the next lower priority to transmit its packets. 802.1Q Tag Type / Length Data © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 47 Identification Flags Fragment Offset Time to Live Protocol Header Checksum Network Priority Traffic Characteristics Source Address 0 (lowest) Background Destination Address Best Effort Options Padding Excellent Effort Example Internet Datagram Header Critical Applications © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 48 In many networks better performance for one of these parameters is coupled with worse performance on another. Except for very unusual cases at most two of these three indications should be set. ⚫ Weighted round robin (WRR) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 49 This command configures the QoS scheduling ---- -------- ---- -------- ---- -------- ---- -------- mode to high_first, each hardware queue will transmit all of the packets in its buffer before permitting the next lower priority to transmit © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 50 This field displays the number of a port. Select a priority for packets received by the port. Only packets 802.1p Priority without 802.1p priority tagged will be applied the priority you set here. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 51 “Tag Over DSCP” or “DSCP Over Tag”. “Tag Over DSCP” means the 802.1p Mode tag has higher priority than DSCP. Queue ID Select the number of a queue for packets with the priority level. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 52 This field indicates which Queue (0 to 7) you are configuring. Queue ID Multicast Storm Control : None. Queue 0 has the lowest priority and Queue 7 the highest priority. DLF Storm Control : 300pps. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 53 DLF - to specify a limit for the amount of DLF packets received per second. Apply Click Apply to take effect the settings. Refresh Click Refresh to begin configuring this screen afresh. Bandwidth Limitation © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 54 This command disables the bandwidth limit ingress ports PORTLISTS for incoming packets. Refresh Click Refresh to begin configuring this screen afresh. Example: [DEVICE_NAME]#configure terminal [DEVICE_NAME](config)#bandwidth-limit egress 1 ports 1-6 [DEVICE_NAME](config)#bandwidth-limit ingress 1 ports 1-6 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 55 VLAN. systems multicast group (224.0.0.1), has a Group Address field of 0, and has a Max Immediate Leave is only supported on IGMP Version 2 hosts). Response Time of [Query Response Interval]. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 56 The default port Immediate Leave state is disabled for all ports. an IGMP multicast router (or server). You The default port Querier Mode state is auto for all ports. must enable IGMP snooping as well. The IGMP snooping Report Suppression is disabled. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 57 Switch not perform IGMP snooping. Specify the action to perform when the Switch receives an Unknown unknown multicast frame. Select Drop to discard the frame(s). Multicast Packets Select Flooding to send the frame(s) to all ports. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 58 Switch uses the port as an IGMP query port if the port bits of available address space. Querier Mode receives IGMP query packets. Fixed means the Switch always treats the port(s) as IGMP query port(s). This is for when © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 59 The Open Shortest Path First (OSPF) AllSPFRouters address. Used to 224.0.0.5 send Hello packets to all OSPF routers on a network segment The OSPF AllDRouters address. Used to send OSPF routing information 224.0.0.6 to OSPF designated routers on a network segment © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 60 Click Apply to save your changes back to the Switch. Refresh Click Refresh to begin configuring this screen afresh. CLI Configuration Node Command Description enable show mac-address-table This command displays the current multicast static/dynamic multicast address entries. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 61 [DEVICE_NAME](config)#interface 1/0/3 [DEVICE_NAME](config-if)#port-isolation ports 1 [DEVICE_NAME](config-if)#exit ; Allow the port-3 to send its ingress packets to port-1 CLI Configuration Node Command Description enable show port- This command displays the current port isolation isolation configurations. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 62 VID (except the ingress port itself), reserved, so the maximum possible VLAN configurations are 4,094. thus confining the broadcast to a specific domain. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 63 PORTLISTS This command assigns ports for tagged Notice: The maximum VLAN group is 4094. member of the VLAN group. The ports should be one/some of the permanent members of the vlan. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 64 This command removes a range of vlans. vlan-range add PORTLISTS This command adds a port or a range of ports to the vlans. vlan-range fixed PORTLISTS This command assigns ports for permanent member of the VLAN group. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 65 Refresh Click Refresh to begin configuring this screen afresh. Tag Status VLAN ID This field displays the VLAN ID. Tag Ports This field displays the ports that have been assigned as tag ports. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 66 This command creates a mac-vlan entry with the vlan VLANID priority leading three or more bytes of mac address and Refresh Click Refresh to begin configuring this screen afresh. <0-7> the VLAN and the priority. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 67 Click the “Delete” button to delete the protocol VLAN profile. the remote ID, the circuit ID, or both to assign IP addresses and implement policies, such as restricting the number of IP addresses that can be assigned to a single © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 68 -Add the transmit port ID into the Circuit sub-option. 0x01 Circuit Form FRAME -Add the frame ID into the Circuit sub-option. The frame ID is configured with the CLI command, “dhcp- options option82 circuit_frame VALUE”. Or GUI Circuit Frame. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 69 VALUE Circuit Frame: configure dhcp-options This command configures the slot ID for the Circuit Shelf: option82 circuit_slot circuit sub-option. VALUE Circuit Slot: Circuit ID String: %HOSTNAME+%SPACE+eth/+%FRAME+/+%SHELF+/+%SLOT+:+%PORT+_+%SVLAN+:+%C VLAN Remote ID String: %HOSTNAME+%SPACE+eth/+%FRAME+/+%SHELF+/+%SLOT+:+%PORT+_+%SVLAN+:+%C VLAN © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 70 The shelf ID for the circuit sub-option. administrator uses DHCP relay agents to centralize DHCP servers, avoiding the need for a DHCP server on each subnet. Circuit Slot The slot ID for the circuit sub-option. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 71 The DHCP Relay in management VLAN should be enabled. Default Settings: DHCP Server The default global DHCP relay state is disabled. The default VLAN DHCP relay state is disabled for all VLANs. The default DHCP server is 0.0.0.0 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 72 VLAN State Example: [DEVICE_NAME]#configure terminal DHCP Server IP Configures the DHCP server’s IP address. [DEVICE_NAME](config)#interface eth0 [DEVICE_NAME](config-if)#ip address 172.20.1.101/24 [DEVICE_NAME](config-if)#ip address default-gateway 172.20.1.1 [DEVICE_NAME](config)#dhcp relay enable [DEVICE_NAME](config)#dhcp relay vlan 1 [DEVICE_NAME](config)#dhcp helper-address 172.20.1.1 © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 73: Eee (Energy Efficient Ethernet)

    The command disables EEE on the specified ethernet auto Refresh Click this to reset the fields to the last setting. interface. Example: [DEVICE_NAME]#configure terminal [DEVICE_NAME](config-if)#interface gigabitethernet1/0/1 [DEVICE_NAME](config-if)#power efficient-ethernet auto [DEVICE_NAME](config-if)#no power efficient-ethernet auto © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 74: Erps (Ethernet Ring Protection Switching)

    "NR, RB" R-APS messages), with less than 1200 km of ring fibre circumference and fewer than 16 Ethernet ring nodes, the switch completion time (transfer time as defined in [ITU-T G.808.1]) for a failure on a ring link shall be less than 50 ms. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 75 If the Control VLAN is configured for a ring and you want to configure an instance for the Timer for the ERPS ring. (default:0 ms) ring. The control vlan of the instance must be same as the Control VLAN; otherwise, you © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 76 Configures the instance for the ring. The Valid value is from 0 to 30. 0-Disable means the ERPS is running in version 1. The Instance control VLAN of the instance should be same as below Control VLAN. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 77 WTB Timer The WTB time. Ring Status The current ring status. Left Port Status The current left port status. Right Port Status The current right port status. Parameter Description Ring ID The ring ID. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 78 The data vlan of the instance. link-aggregation configure The command disables / enables the trunk on [GROUP_ID] (disable | the specific trunk group. enable) configure link-aggregation The command adds ports to a specific trunk [GROUP_ID] interface group. PORTLISTS © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 79 LACP also allows port redundancy, that is, if an operational port fails, then one of the “standby” ports become operational without user intervention. Please note that: © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 80 <1-65535> This command configures the The default System Priority is 32768. priority for the specific port. The default group LACP state is disabled for all groups. Note: The default value is 32768. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 81 This command configures the default for the priority for the specific ports. Parameter Description Select Enable from the drop down box to enable Link Aggregation Control Protocol (LACP). State Select Disable to not use LACP. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 82 Port State The direct connected port’s state of the neighbor Switch. Port Priority The direct connected port’s priority of the neighbor Switch. Oper Key The Oper key of the LACP member port. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 83 This command configures the destination MAC for the loop Default Settings MACADDR detection special packets. The default global Loop-Detection state is disabled. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 84 Enter the destination MAC address the probe packets will be MAC Address sent to. If the port receives these same packets the port will be shut down. Port Select a port on which to configure loop guard protection. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 85: System Information

    1 word Vendor ID = 0x0b04 0x0001 16 words ASCII Vendor Name = “ABCDEFG Corp.” Word 0 Hi byte = ‘A’ Word 0 Lo byte = ‘B’ Word 1 Hi byte = ‘C’ © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 86 Power 2(RPS) Alarm, DIP switch 1 need ON Word 2 Lo byte = ‘9’ 0x0000: no alarm Word 3 Hi byte = ‘9’ 0x0001: input voltage < 44V Word 3 Lo byte = ‘9’ © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 87 Word 0 Lo byte = ‘0’ 0x0000 : STP is disabled. (port 2) Word 1 Hi byte = ‘0’ 0x0001 : STP … Word 1 Lo byte = ‘T’ 0x0002 : RSTP 0x0320 to … 0x0003 : MSTP © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 88 0x0002 : blocking Word 0 Hi byte = Port ID. 0x0519 1 word Secondary Port of the Xpress-ring1 Word 0 Hi byte = Port ID. 0x051a 1 word Primary Port of the Xpress-ring2 © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 89: Power Over Ethernet

    CLI Configuration Power over Ethernet Node Command Description (Supported Models: TI-PG541i, TI-PG102i, TI-PG102i-M & TI-RP262i) The main advantage of PoE is that it can make installing a network easier. The selection enable show modbus This command displays the current of a location for a network device is often limited by whether there is a power source Modbus configurations.
  • Page 90 This is the lowest priority level. Ports set to the Low level receive power only when all the ports assigned to the Critical and High levels are already receiving power. This level is the default setting. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 91 Selects Enable to enable the PoE function on the specific port. State Selects Disable to disable the PoE function on the specific port. Priority Selects Critical / High / Low priority for the specific port. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 92 PD. Alarm: Just send an alarm message to inform the administrator. None: Keep Ping the remote PD but does nothing further. Reboot: Cut off the power of the PoE port, make PD rebooted. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 93 The action to the Power Device when the system detects that (Sun|Mon|Tue|Wed|Thu|Fri|Sat) the PoE schedule on the specific Action the Power Device cannot respond the keep-a-live probe packet. check (yes|no) day. The options have Reboot / Alarm / All /None. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 94 The slower the media, the higher the cost. Enables or Disables the PoE schedule on the specific port for a Check defined time period. Time (Hour) Select the time (in hours) to start and stop the schedule. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 95 Switch ports attached to the network. The allowed range is 6 to 40 seconds. link fails, without the danger of bridge loops, or the need for manual enabling/disabling of these backup links. Bridge loops must be avoided because they result in flooding the network. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 96 Alternate - An alternate path to the root bridge. This path is different than using the root port. ⚫ Backup - A backup/redundant path to a segment where another bridge port already connects. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 97 Root Bridge status. The port can be moved to forwarding state if no superior This command displays the BPDU received by this port for three hello times. enable show spanning-tree active spanning tree information for only active port(s) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 98 (disable|enable) This command configures the port. configure spanning-tree hello-time <1-10> bridge hello time(sec). This command configures the cost interface spanning-tree cost VALUE for the specific port. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 99 Parameter Description This command configures the cost Select Enabled to use Spanning Tree Protocol (STP) or Rapid State if-range spanning-tree cost VALUE for the specific port. Spanning Tree Protocol (RSTP). Cost range: © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 100 Path cost is the cost of transmitting a frame on to a LAN Pathcost through that port. It is recommended to assign this value Path Cost Configures the path cost for the specific port. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 101 This is the MAC address of the current bridge. Priority is used in determining the root switch, root port and Priority designated port. The switch with the highest priority (lowest numeric value) becomes the STP root switch. If all switches © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 102 The slower the media, the higher the cost. This is the number of the port on the Switch through which this Root Cost Switch must communicate with the root of the Spanning Tree. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 103: Security

    DHCP server or another switch. Untrusted ports are connected to subscribers. The Switch discards DHCP packets from untrusted ports in the following situations: ⚫ The packet is a DHCP server packet (for example, OFFER, ACK, or NACK). © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 104 When the global state is disabled, the DHCP Snooping on the Switch is disabled even per VLAN states are enabled. When the global state is enabled, user must enable per VLAN states to enable the DHCP Snooping on the specific VLAN. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 105 C. [DEVICE_NAME](config)#interface gi1/0/1 D. [DEVICE_NAME](config-if)#dhcp-snooping trust configure interface range This command enters the interface DHCP Client-1: ipconfig /release gigabitethernet1/0/ PORTLISTS configure node. DHCP Client-1: ipconfig /renew ➔ DHCP Client-1 can get an IP address. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 106 This field displays the VLAN IDs that have DHCP snooping Security > IP Source Guard > DHCP Snooping > DHCP Snooping Enabled on VLAN enabled on them. This will display None if no VLANs have been set. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 107 Security > IP Source Guard > DHCP Snooping > Port Settings DHCP server’s IP. configure no dhcp-snooping server IPADDR This command removes a valid DHCP server’s IP. Web Configuration Security > IP Source Guard > DHCP Snooping > Server Screening © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 108: Binding Table

    Enter the source VLAN ID in the binding. configure no dhcp-snooping binding mac This command removes a static Port Specify the port in the binding. MACADDR host from the DHCP snooping binding table. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 109 This field displays how the Switch learned the binding. Static: This binding was learned from information provided Type manually by an administrator. Dynamic: This binding was learned by snooping DHCP packets. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 110: Arp Inspection

    Inspection function on a VLAN or range of VLANs. The ARP Inspection on the Switch is disabled. The age time for the MAC filter is 5 minutes. ARP Inspection is enabled in VLAN(s): None. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 111 Enabled on VLAN enabled on them. This will display None if no VLANs have been set. This field displays the ports which are trusted. This will display Trusted Ports None if no ports are trusted. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 112: Filter Table

    This field displays a sequential number for each MAC address configure clear arp-inspection mac-filter This command clears all of entries filter. in the filter table. This field displays the source MAC address in the MAC address MAC Address filter. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 113 2. Filter a specific destination MAC address. Command: destination mac host MACADDR 3. Filter a range of source MAC address. Command: source mac MACADDR MACADDR The second MACADDR is a mask, for example: ffff.ffff.0000 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 114 MAC and mask from the profile. source ip host IPADDR This command configures the 802.1p VALUE This command configures the source IP address for the profile. 802.1p value for the profile. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 115 This command removes the VLAN: 2 limitation of the VLAN from the Source Interface: 1 profile. Destination MAC Address: any source interface PORT_ID This command configures the Source MAC Address: any source interface for the profile. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 116 Mask of Configures the bitmap mask of the destination IP of the packets Destination IP that you want to filter. Action Selects Disables / Drop / Permits / DSCP action for the profile. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 117 An analogy to this is providing a © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 118 Port Control Mode: The default port Server timeout is 30 seconds for all ports. auto: Users can access network after authenticating. force-authorized: Users can access network without authentication. force-unauthorized: Users cannot access network. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 119 <STRING> account for local authentication. interface dot1x guest-vlan This command configures the (disable|enable) 802.1x state on the port. configure no dot1x username <STRING> This command deletes the user account for local authentication. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 120 The Local method of authentication uses the “guest” and “user” Server the Primary Radius Server. This will be blank if nothing has Method user groups of the user account database on the Switch itself to been set. authenticate. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 121 Specify a period of the time the client has to wait before the next re-authentication attempt. This will prevent the Switch Quiet period from becoming overloaded with continuous re-authentication attempts from the client. The acceptable range for this field is 0 to 65535 seconds. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 122 This field displays the Guest VLAN setting for hosts that have Guest VLAN not passed authentication. Note: If you configure a port of the Switch from disabled to enabled, all of the MAC learned by this port will be clear. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 123 Port Security Status Port This field displays a port number. State This field displays if Port Security is Enabled or Disabled Maximum MAC This field displays the maximum number of MAC addresses © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 124 This command displays the link up ports’ statistics. Web Configuration Monitor > Alarm Example: show port-statistics [DEVICE_NAME]# Packets Bytes Errors Drops Port ---- -------- -------- -------- -------- -------- -------- -------- -------- 3 1154 108519 1188 Parameter Description © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 125 The field displays the transmitted drop count. Speed The current port speed. Refresh Click this button to refresh the screen quickly. Utilization The port traffic utilization. Refresh Click this button to refresh the screen quickly. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 126 Parameter Description Show Show them. Port Select a port number to configure. Clear Clear the RMON statistics for the port or a range of ports. Apply Click Apply to display the SFP information. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 127 12 Disabled Normal Bcast 1000 Enabled 1 13 Disabled Normal Bcast 1000 Enabled 1 14 Disabled Normal Bcast 1000 Enabled 1 15 Disabled Normal Bcast 1000 Enabled 1 16 Disabled Normal Bcast 1000 Enabled 1 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 128 This command enables / disables the function on these ports. (disable|enable) recovery function for the traffic monitor on Configures the recovery time for the traffic monitor function on the port. Recovery Time these ports.(Range: 1 – 60 minutes) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 129 (v1 or v2c) and community. User configures the Community String and the Rights and the Network ID of Trusted Host=0.0.0.0, Subnet Mask=0.0.0.0. It means that all hosts with the community string can access the Switch. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 130 (The System Name is same as the host name) Rights Select Read-Write to allow the SNMP manager using this string to System Location Type a System Location for the Switch. create or edit MIBs (configure settings on the Switch). © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 131 Click the number to modify the entry. IP Address This field displays the IP address of the remote trap station. This field displays the version of Simple Network Management Version Protocol in use. v1 or v2c. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 132 Global_Configuration_File=8648P-999-1.1.0.S0.save Version: Global_Configuration_Reboot=0 Protocol: Specific_Configuration_State=0 FTP user/pwd: Specific_Configuration_Reboot=0 Folder: If AUTO_PROVISION_VER is biggest than current auto provision version, do step 3; Server address: otherwise, wait 24 hours and go back to step 1. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 133 : A user login the system. ◆ Port Blocked : A port is blocked by looping detection or BPDU guard. Default Settings Mail-Alarm Configuration: ----------------------------------------------- State : Disabled. Server IP : 0.0.0.0 Server Port : 25 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 134 IP address and the TCP port. Outlook.com Server: Authentication: Port: configure mail-alarm server-ip This command configures the mail IPADDR server-port Default server IP address and configures 25 as SMTP Server (Outgoing smtp.live.com StartTLS the server’s TCP port. Messages) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 135 Specifies the mail account name. Account Password Specifies the mail account password. Mail From Specifies the mail sender. Mail To Specifies the mail receiver. Trap State Enables / disables the mail trap event states. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 136 TFTP / FTP / HTTP server. Upload / Download Configuration to /from a your server Where <URL PATH> can be: ftp://user:pass@192.168.1.1/file http://192.168.1.1/file tftp://192.168.1.1/file Example: [DEVICE_NAME]#configure terminal [DEVICE_NAME](config)#interface eth0 [DEVICE_NAME](config-if)#ip address 172.20.1.101/24 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 137 This command disables the telnet on the Switch. configure web server This command enables the web on the Switch. configure no web server This command disables the web on the Switch. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 138 This does not affect the Switch’s configuration. Web Server Status Displays the current Web service status. Telnet Server Status Displays the current Telnet service status. SSH Server Status Displays the current SSH service status. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 139: User Account

    Users should input a valid user account to login the CLI or web [DEVICE_NAME](config)#syslog-server enable management. User Authority: The Switch supports two types of the user account, admin and normal. The default user’s account is username (admin) / password (admin). © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 140 This field displays the index number of an entry. (normal|admin) User Name This field displays the name of a user account. configure delete user This command deletes a present user USER_ACCOUNT account. User This field displays the password. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 141: Device Management

    This command configures the interval to transmit the LLDP packets. configure lldp tx-hold This command configures the tx-hold time which determines the TTL of the Switch’s message. (TTL=tx-hold * tx-interval) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 142 – Receive the LLDP packet on the specific port. configure interface range This command enters the interface configure gigabitethernet1/0/ node. PORTLISTS Parameter Description State Globally enables / disables the LLDP on the Switch. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 143 This command configures the onvif packets transmit interval to the default value configure no onvif binding- This command binds the MAC address to a ports particular port © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 144 Enter the MAC address of the device to add to the topology map. plc mac display on netlite. MAC Address (00:11:22:aa:bb:cc) configure netlite-device type This command binds the MAC address to a switch mac particular port configure no netlite-device This command removes device from netlite.. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 145: Toplogy Map

    Refresh Manually refresh the topology map/netlite page. Background Modify the background color of the topology map or upload a Configuration background image. Zoom Zoom in or out of the topology map/netlite viewing page. © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 146: Technical Specifications

    Fast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex) • Storm control: Broadcast, multicast, destination lookup failure (Min. limit: • Gigabit Ethernet: 2000Mbps (full duplex) 1pps) • SFP: 2000Mbps (full duplex) • Loopback detection • DHCP relay/option 82 © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 147 PoE budget: 685W @ 48V DC input • IGMP fast/immediate leave • 802.3at: Up to 30W per port • Up to 256 multicast groups • PoE Mode A: Pins 1, 2, 3, and 6 for power © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 148 • -40° – 70° C (-40° – 158° F) Operating Humidity • Max. 95% non-condensing Dimensions • 440 x 310 x 44mm (17.3 x 12.3 x 1.7 in.) Weight • 3.58kg (7.89 lbs.) © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 149: Ti-Pg541I

    MAC-based VLAN • MAC address table: 8K entries • Port isolation • Jumbo frames: 10 KB • Up to 256 VLAN groups, ID range 1-4094 • Forwarding rate: 8.93 Mpps (64-byte packet size) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 150 Up to 30W per port for PoE+ • Mode A: Pins 1, 2 (V+) and pins 3, 6 (V-) • PoE enable/disable per port setting, priority, scheduling, power delay, and PD alive check Enclosure • IP30 rated metal enclosure © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 151 Ethernet: 10Mbps (half-duplex), 20Mbps (full-duplex) • Loopback detection • Fast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex) • • DHCP relay/option 82 Gigabit Ethernet: 2000Mbps (full duplex) • SFP DDMI (Digital Diagnostic Monitoring Interface) Performance © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 152 Compatible power supply: TI-S12024 (120W), TI-S24048 (240W), TI-S48048 • IGMP querier (480W) sold separately • IGMP fast leave • Max. Consumption: 13W (no PoE load), 253W (full PoE load) • Up to 256 multicast groups • Static multicast entries © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 153 Freefall (IEC 60068-2-32) • Vibration (IEC 60068-2-6) Enclosure • IP30 rated metal enclosure • Fanless passive cooling • DIN-Rail mount • Grounding point • ESD (Ethernet) Protection: 8KV DC • Surge (Power) Protection: 6KV DC © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 154: Ti-G642I

    • IGMP querier • MAC address table: 8K entries • IGMP fast leave • Jumbo frames: 10KB • Up to 256 multicast groups • Forwarding mode: store and forward • Static multicast entries © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 155 Stranded wire (AWG): 12-26 DHCP snooping/screening • • Wire strip length: 10-11mm Trusted host/IP access list for management access • Port Security/MAC address learning restriction (Up to 100 entries per port) • Static/dynamic ARP inspection © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 156 Open circuit mode when two power sources are connected Enclosure • IP30 rated metal enclosure • Fanless passive cooling • DIN-Rail mount • Grounding Point • ESD (Ethernet) Protection: 8KV DC • Surge (Power) Protection: 2KV DC © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 157: Ti-G102I

    Fast Ethernet: 100Mbps (half duplex), 200Mbps (full duplex) • DHCP relay/option 82 • Gigabit Ethernet: 2000Mbps (full duplex) • Modbus/TCP Performance • SFP DDMI (Digital Diagnostic Monitoring Interface) • Switch fabric: 20Gbps • RAM buffer: 128MB © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 158 Compatible power supply: TI-M6024 (60W), TI-S12024 (120W), TI-S12048 • IGMP querier (120W), and TI-S24048 (240W) sold separately • IGMP fast leave • Max. consumption: 13W • Up to 256 multicast groups • Static multicast entries © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 159 Port 9 SFP set to 100Mbps speed full duplex • Port 10 SFP set to Gigabit speed full duplex • Shock (IEC 60068-2-27) • Freefall (IEC 60068-2-32) Port 10 SFP set to 100Mbps speed full duplex • Vibration (IEC 60068-2-6) © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 160: Ti-G160Ws

    MIB II RFC 1213 • Switch fabric: 32Gbps • Bridge MIB RFC 1493 • RAM buffer: 128MB • • RMON (Group 1,2,3,9) RFC 1757 MAC address table: 8K entries • Jumbo frames: 10KB © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 161 802.1X authentication (Local user database, RADIUS, guest VLAN assignment) • • Wire strip length: 10-11mm DHCP snooping/screening • Trusted host/IP access list for management access • Port Security/MAC address learning restriction (Up to 100 entries per port) • Static/dynamic ARP inspection © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 162 -40° – 75° C (-40° – 167° F) Operating Humidity • Max. 95% non-condensing Dimensions • 160 x 120 x 50mm (6.3 x 4.72 x 1.97 in.) Weight • 884 g (1.95 lbs.) © Copyright 2018 TRENDnet. All Rights Reserved.

  • Page 163: Ti-G160I

    MIB II RFC 1213 • Switch fabric: 32Gbps • Bridge MIB RFC 1493 • RAM buffer: 128MB • • RMON (Group 1,2,3,9) RFC 1757 MAC address table: 8K entries • Jumbo frames: 10KB © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 164 802.1X authentication (Local user database, RADIUS, guest VLAN assignment) • • Wire strip length: 10-11mm DHCP snooping/screening • Trusted host/IP access list for management access • Port Security/MAC address learning restriction (Up to 100 entries per port) • Static/dynamic ARP inspection © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 165 -40° – 75° C (-40° – 167° F) Operating Humidity • Max. 95% non-condensing Dimensions • 160 x 120 x 50mm (6.3 x 4.72 x 1.97 in.) Weight • 884 g (1.95 lbs.) © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 166 Then click Use the following IP address, and make sure to assign your network adapter an IP address in the subnet of 192.168.10.x. Click OK Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 167 From the Location drop-down list, select Automatic. 2. In the Network Preference window, next to "Show:", select Network Status. You'll see d. Select and view your Ethernet connection. your network status and your IP address settings displayed. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 168 2. Select Ethernet from the list on the left. Example: ping –c 4 192.168.10.100 3. Click the Advanced button. 3. On the Ethernet tab, the Ethernet ID is your MAC Address. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 169 Country Code selection feature to be disabled for products marketed to the US/CANADA CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. © Copyright 2018 TRENDnet. All Rights Reserved.
  • Page 170 An RMA number is required in order to initiate warranty service support the event that the RMA unit needs to be replaced, TRENDnet may replace it with a for all TRENDnet products. Products that are sent to TRENDnet for RMA service must refurbished product of the same or comparable model.
  • Page 171 OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND evidence of the original purchaser's date of purchase. Replacement products may be OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY refurbished or contain refurbished materials. If TRENDnet, by its sole determination, is...

This manual is also suitable for:

Ti-pg102iTi-pg102i-mTi-g642iTi-g102iTi-g160wsTi-g160i

Table of Contents