Mitsubishi Electric PLK-G-PAL Technical Manual page 196

CODE
M-103 MAKE CIRCLE DATA?
M-104 MAKE CURVE DATA?
M-105 MAKE BROKEN LINE DATA?
M-106 MOVING TO END DATA
M-107 MATERIAL THICKNESS WARNING
M-108 OUT OF DATA NUMBER(300point)
M-120 MOVING TO START POINT
M-121 MOVING TO STARTING POSITION
M-122 A SPECIFIED POSITION IS WRONG
M-123 THE AMOUNT OF THE MOVEMENT IS NOT INPUT
M-124 A SPECIFIED POSITION IS WRONG
M-125 A SPECIFIED POSITION IS WRONG
M-126 A SPECIFIED POSITION IS WRONG
M-127 A SPECIFIED POSITION IS WRONG
M-128 A SPECIFIED POSITION IS WRONG
M-130 SEWING DATA DOES NOT EXIST
M-131 A SPECIFIED POSITION IS WRONG
M-140 OFFSET DATA DOES NOT EXIST
M-141 MULTIPLE DATA DOES NOT EXIST
M-144 THE POINT INPUT DATA CANNOT BE CONVERTED.
M-161 HALT SWITCH IS ON
M-162 ILLEGAL NUMBER WAS SET
M-164 NOT G-DATA
M-165 NOT G-DATA
M-180 Cassette jig sensor is not detected
M-188 USB MEDIUM IS NOT CONNECTED
M-189 CAN NOT BE SAVED INTO USB MEDIUM
M-190 USB MEDIUM DEFECT
M-191 INSUFFICIENT EMPTY AREA IN USB MEDIUM
M-192 SPECIFIED DATA DOES NOT EXIST IN THE USB MEDIUM
M-193 OPTIMIZING INTERNAL MEMORY
M-194 CLEARS CONTENT OF THE SHORT CUT BUTTON
M-195 WRITING SEWING DATA INTO USB MEDIUM
M-197 READING SEWING DATA
M-198 OVERWRITES DATA IN USB MEDIUM
M-199 DELETES SEWING DATA IN USB MEDIUM
M-201 CORRESPONDING DATA DOES NOT EXIST IN USB MEDIUM
M-202 READING FILE INFORMATION OF THE USB MEDIUM
M-203 USB MEDIUM IS CONNECTED
M-204 READING COMPLETE
M-205 WRITING COMPLETE
M-209 INTERNAL MEMORY DEFECT
M-210 SAVED FILE NUMBER IS OVER LIMIT
M-211 SPECIFIED SEWING DATA DOES NOT EXIST IN THE MEMORY
M-212 MEMORY FORMATTING...
M-214 THERE IS NO NUMBER THAT HAS BECOME EMPTY IN MEMORY
MESSAGE
FROM USB MEDIUM
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON
PLEASE WAIT FOR A WHILE
MATERIAL STEP VALUE OF SEWING DATA IS OUT OF RANGE.
PLEASE CHECK MATERIAL STEP VALUE.
PLEASE DECREASE THE INPUT POINT
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
PLEASE SPECIFY FOLLOWING STITCH FROM START POINT
PLEASE INPUT AMOUNT OF MOVEMENT
PLEASE SPECIFY SEWING DATA
PLEASE SPECIFY SEWING AND FEED DATA
PLEASE SPECIFY ONE STITCH FRONT IS SEW OR FEED DATA
PLEASE SPECIFY PREVIOUS DATA FROM FINAL STITCH
PLEASE SPECIFY CODE DATA
THIS FUNCTION CANNOT BE USED
PLEASE SPECIFY ONE STITCH REAR IS SEW OR FEED DATA
PLEASE SPECIFY SEWING DATA OTHER THAN THE POINT INPUT.
RELEASE HALT SWITCH. IF MESSAGE IS NOT CLEAR AFTER RELEASE HALT SWITCH, TURN
THE POWER OFF AND CHECK HALT SWITCH & CABLE
PLEASE SETTING AGAIN
PLEASE SPECIFY THE "G DATA"
PLEASE SPECIFY THE "G DATA"
PLEASE CONNECT USB MEDIUM
PATTERN DATA THAT WAS CREATED BY A FORMER SERIES CAN NOT BE SAVED
PLEASE CHANGE USB MEDIUM
PLEASE CHANGE USB MEDIUM OR
CHECK FILE NAME AND PATTERN DATA NUMBER
PLEASE WAIT FOR A WHILE
ARE YOU SURE? Yes: ENTER ICON(PATTERN DATA WILL NOT BE ERASED)
No: X ICON
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
ARE YOU SURE? Yes: ENTER ICON
ARE YOU SURE? Yes: ENTER ICON
PLEASE CHANGE USB MEDIUM
PLEASE WAIT FOR A WHILE
PLEASE DETACH USB MEDIUM
PLEASE DETACH USB MEDIUM
PLEASE DETACH USB MEDIUM
INTERNAL MEMORY WILL BE FORMATTED. PRESS ENTER ICON
PLEASE ERASE UNUSED DATA
CHECK FILE NAME AND PATTERN DATA NUMBER
PLEASE WAIT FOR A WHILE
PLEASE DELETE UNNECESSARY DATA
SUB-MESSAGE
No: X ICON
No: X ICON
No: X ICON
DELETE FILES
No: X ICON
No: X ICON