M-***] Message Code - Mitsubishi Electric PLK-G-PAL Technical Manual

2．[M-***] Message code
CODE
M-001 NEEDLE IS NOT CORRECT POSITION
M-002 NEEDLE THREAD WAS BROKEN
M-003 CLAMP IS UP
M-004 UP COUNTER SET VALUE UP
M-005 DOWN COUNTER REACHED SET VALUE
M-006 PATTERN DATA DOES NOT EXIST
M-007 CLAMP IS NOT AT HOME POSITION
M-008 SERIAL DATA TRANSMITTING...(RS232C)
M-009 SERIAL DATA RECEIVING...(RS232C)
M-010 HALT SWITCH IS ON
M-011 PLEASE RUN SEWING MACHINE
M-012 THE HALT SWITCH IS TURNED ON.
M-014 CURRENT UP COUNTER VALUE IS PROTECTED
M-015 CURRENT DOWN COUNTER VALUE IS PROTECTED
M-016 CURRENT COUNTER VALUE HAS EXCEEDED THE SET VALUE
M-018 THE SETTING TABLE NUMBER IS CHANGED
M-019 SEWING DATA DOES NOT HAVE END CODE
M-020 START INPUT SIGNAL IS TURNING ON
M-024 CLAMP WILL MOVE TO THE SECOND HOME POSITION
M-026 START SIGNAL AND JOG - ICON IS INEFFECTIVE
M-027
NEEDLE UP POSITION DETECTION WARNING
M-028 TERMINATION PROCESS COMPLETE
M-029 SETTING WILL NOT CHANGE
M-030 STITCH POSITION IS DEVIATED FROM THE SEWING PATTERN
M-032 THIS IS NOT COMPLIANT CODE AT THIS SYSTEM VERSION.
M-033 IT IS SET TO [M2H]=HP2
M-034 STITCH NUMBER COUNTER 1 REACHED TO SETTING VALUE
M-035 STITCH NUMBER COUNTER 2 REACHED TO SETTING VALUE
M-036 THE PATTERN CHANGES
M-037 INCORRECT RELEASE CODE
M-038 MACHINE HEAD TILT WAS DETECTED
M-039 BOARD TEMPERATURE WARNING
M-040 STEP SEQUENCE PROGRAM ERROR
M-042 S6 SIGNAL BEING DETECTED
M-043 START PROHIBIT SIGNAL BEING DETECTED
M-044 COUNTER REACHED SET VALUE
M-050 NOT IN THE HOME POSITION
M-051 ILLEGAL SETTING
M-052 SET VALUE IS TOO LARGE
M-053 SET VALUE IS TOO SMALL
M-054 DATA DOES NOT EXIST
MESSAGE
RETURN NEEDLE TO UP POSITION BY HAND OR NEEDLE UP ICON
PLEASE THREAD THE NEEDLE
TURN ON THE FOOT SWITCH (BLACK FOOT SWITCH)
Please touch Enter Icon
Please touch Enter Icon
READING OR TEACHING INPUT
PRESS HOME ICON
PLEASE WAIT FOR A WHILE
PLEASE WAIT FOR A WHILE
PLEASE PUSH HALT SWITCH AGAIN
PLEASE ROTATE THE SEWING MACHINE BY THE WINDER OR SEWING
START SWITCH, +JOG, -JOG ICON IS INVALID. PLEASE TURN THE POWER OFF.
*AFTER POWER LED IS TURNED OFF, TURN ON THE POWER.
PLEASE TURN OFF PROHIBITION WHEN CORRECTING.
PLEASE TURN OFF PROHIBITION WHEN CORRECTING.
CURRENT VALUE MUST BE SMALLER THAN SETTING VALUE
THE SET TABLE NUMBER IS SET IN THIS SEWING DATA
PLEASE ADD END CODE
PLEASE TURN OFF START INPUT SIGNAL
ARE YOU SURE? Yes: ENTER ICON
PRESS +JOG ICON
THE MAIN SHAFT WILL ROTATE TO DETECT UP POSITION. ATTENTION BEING CAUGHT IN THE
MACHINE.
SEE YOU AGAIN ! * WAIT UNTIL THE LED OF THE CONTROL BOX IS COMPLETELY OFF,
THEN POWER THE SWITCH ON AGAIN.
ARE YOU SURE? Yes: ENTER ICON
PRESS +JOG OR -JOG ICON, THEN START SEWING.
PLEASE OPERATE IT AGAIN, AFTER IT SETS [M2H] IN ON OR OFF
CLR: STITCH NUMBER COUNTER 1 IS CLEARED.
ENT: CLEARS MESSAGE
CLR: STITCH NUMBER COUNTER 2 IS CLEARED.
ENT: CLEARS MESSAGE
PRESS HOME ICON
PLEASE INPUT AGAIN
THE MACHINE HEAD IS TILTED POSITION. IF MACHINE HEAD IS NORMAL POSITION, CHECK
THE MACHINE TILT SWICH AND CABLE.
BOARD TEMPERATURE IS HIGH
PLEASE CORRECT THE STEP SEQUENCE
PLEASE RELEASE THE S6 SIGNAL.
PLEASE RELEASE THE START PROHIBIT INPUT SIGNAL.
PLEASE CLEAR THE COUNTER.
PRESS HOME ICON
PLEASE INPUT A CORRECT VALUE
PLEASE INPUT THE VALUE WITHIN THE RANGE
PLEASE INPUT THE VALUE WITHIN THE RANGE
SUB-MESSAGE
No: X ICON
No: X ICON