Other - Mitsubishi Electric PLK-G-PAL Technical Manual

19.Other

Function
SC1
Valid/invalid serial
communication 1
<TURN OFF THE
POWER>
BR1
Setting for baud rate for
serial communication 1
<TURN OFF THE
POWER>
BM1
Arbitrary setting for serial
communication 1
<TURN OFF THE
POWER>
SC2
Valid/invalid serial
communication 2
<TURN OFF THE
POWER>
BR2
Setting of baud rate for
serial communication 2
<TURN OFF THE
POWER>
BM2
Arbitrary setting for serial
communication 2
<TURN OFF THE
POWER>
MIL
Milling mode ON/OFF
<TURN OFF THE
POWER>
MLC
Setting for migration
coefficient of XY table at
the milling mode.
BOM
Setting for the control box
temperature warning
CDD
Display of code in image
setting
RF
Forward rotation angle setting
ADS
Angle operation speed setting
ND1
Needle change delay 1 setting
ND2
Needle change delay 2 setting
ND3
Needle change delay 3 setting
Unit Setting range
Validates/invalidates serial communication 1.
Please turn off the power after the setting change and restart again.
- OF
ON
Sets baud rate for serial communication 1.
Please turn off the power after the setting change and restart again.
- 96
384
576
1152
OF
× 96 ~ 2560
100
bps
Valid/invalid serial communication 2.
Please turn off the power after the setting change and restart again.
- OF
ON
Sets baud rate for serial communication 2.
Please turn off the power after the setting change and restart again.
- 96
384
576
1152
OF
× 96 ~ 2560
100
bps
Sets valid/invalid of milling function.
Please turn off the power after the setting change and restart again.
- OF
ON
Sets for migration coefficient of XY table at the milling mode.((speed dial value+1)x(MLC
Value)x0.1mm)/17ms
- S
M
L
Sets valid/invalid for the control box temperature warning detection.
- OF
ON
The method of displaying the code of the sewing data image display is set.
- DP
CR
NO
deg. 0 ~ 150
rpm 100 ~ 1000
ms 10 ~ 9999
ms 10 ~ 9999
ms 10 ~ 9999
Invalidates serial communication 1
Validates serial communication 1
Sets baud rate 9600bps
Sets baud rate 38.4kbps
Sets baud rate 57.6kbps
Sets baud rate 115.2kbps
Set baud rate to the value which is set by BM1
Sets arbitrary board rate of serial communication 1
Please turn off the power after the setting change and restart
again.
Invalidates serial communication 2
Validates serial communication 2
Sets baud rate 9600bps
Sets baud rate 38.4kbps
Sets baud rate 57.6kbps
Sets baud rate 115.2kbps
Set baud rate to the value which is set by BM2
Sets arbitrary board rate of serial communication 2
Please turn off the power after the setting change and restart
again.
XY table is operated with normal mode.
XY table is operated with milling mode. The movement speed of XY table
is changed by speed dial value on standard screen (Migration coefficient
of XY table at the milling mode[MLC]). ((speed dial value+1)x(MLC
Value)x0.1mm)/17ms
Default setting (Small) [S]
Middle [M]
Large [L]
Invalidates control box temperature warning detection.
Validates control box temperature warning detection.
The content of the code is displayed.
All the codes are displayed by "Circle".
The code is not displayed.
Sets forward rotation angle.
Sets angle operation speed.
Needle change delay 1 (Sets the time from end of needle up to
turning on of the needle change solenoid)
Needle change delay 2 (Sets the time from needle change
solenoid on to start reverse rotation)
Needle change delay 3 (Sets the time end of reverse rotation to
start forward rotation)
[16] - 15
Specification