Mitsubishi Electric PLK-G-PAL Technical Manual page 195

CODE
M-055 TOO MANY STITCHES
M-056 OUT OF DATA NUMBER(5000point)
M-057 OUT OF AREA LIMIT
M-058 TOO SHORT STITCH LENGTH
M-059 TOO LONG STITCH LENGTH
M-060 SECOND HOME ALREADY EXISTS
M-062 TOO LONG NON STITCH FEED
M-063 NUMBER OF SKIP JOG IS OUT OF RANGE
M-064 COULD NOT CALCULATE
M-065 NOT IN HOME POSITION
M-066 DATA TYPE IS DIFFERENT
M-067 CURVE DATA COULD NOT BE CREATED
M-068 PREPARING IMAGE DISPLAY.....
M-070 CURVE DATA CAN NOT BE CREATED
M-071 THERE IS NO DATA TO BE DELETED
M-072 TRIMMING CODE CAN NOT BE INPUTTED OR ADDED
M-073 CODE CAN NOT BE INPUTTED OR ADDED.
M-074 THE SECOND HOME POSITION CAN NOT BE INPUTTED
M-075 THE END CODE CAN NOT BE INPUTTED
M-076 CIRCLE OR ARC COULD NOT BE CREATED
M-077
THE OVERLAP BACK TACKING CANNOT BE SPECIFIED
M-080 TOO LONG STITCH
M-082 ILLEGAL SETTING
M-083 TRIM CODE CAN'T BE INPUTTED NOR ADDED
M-084 DSTP CODE CAN NOT BE INPUTTED NOR ADDED
M-085 CLAMP POSITION HAS DEVIATED FROM INPUT COORDINATES
M-086 CLAMP POSITION HAS DEVIATED FROM INPUT COORDINATES
M-087 ZIGZAG DATA CAN NOT BE CREATED.
M-088 MULTIPLE, ZIGZAG, BACK TACKING CAN NOT BE SET
M-089 DATA CAN NOT BE CREATED.
M-090 CIRCLE OR ARC COULD NOT BE CREATED
M-092 CLAMP POSITION HAS DEVIATED FROM INPUT COORDINATES
M-093 THICKNESS OF MATERIAL IS
M-094 PRESSER FOOT IS DOWN
M-095 MATERIAL THICKNESS IS OUT OF RANGE
M-096 MATERIAL THICKNESS SETTING VALUE WARNING
M-097 INPUT VALUE IS OUT OF RANGE
M-098 MODIFICATION VALUE IS OUT OF RANGE
M-099 MATERIAL STEP IS OUT OF THICKNESS RANGE
M-100 MAKING DATA...
M-102 MAKE ARC DATA?
MESSAGE
PLEASE DECREASE THE NUMBER OF STITCH
PLEASE DECREASE THE INPUT POINT
PLEASE MAKE THE DATA IN THE AREA LIMIT
PLEASE INPUT THE VALUE WITHIN THE RANGE
PLEASE INPUT THE VALUE WITHIN THE RANGE
ONLY ONE SECOND HOME POSITION POINT CAN BE INPUT
PLEASE CORRECT NON STITCH FEED DATA
PLEASE INPUT THE VALUE WITHIN THE RANGE
PLEASE DECREASE THE INPUT POINT AND THE AMOUNT OF THE MOVEMENT AND INPUT
AGAIN
PRESS HOME ICON
PLEASE CONFIRM DATA TYPE
PLEASE INPUT AGAIN REFERRING TO CURVE INPUT NOTES
PLEASE WAIT FOR A WHILE
PLEASE REVIEW INPUT POINT
PLEASE INPUT AND ADD THE TRIM AFTER SEW
SAME CODE CAN NOT BE ADDED CONTINUOUSLY
PLEASE INPUT AND ADD THE 2HD AFTER FEED
PLEASE INPUT AND ADD THE END AFTER FEED OR TRIM
PLEASE REVIEW INPUT POINT
THE OVERLAP BACK TAKING CAN BE USED ONLY FOR THE FIGURE WHERE CIRCLE, CURVE,
AND BROKEN LINE SHUT.
PLEASE CHANGE THE PATTERN DATA
PLEASE INPUT A CORRECT VALUE
TRIM CODE CAN NOT BE ADDED JUST AFTER NEEDLE DOWN STOP CODE
NEEDLE DOWN STOP CODE CAN NOT BE ADDED JUST BEFORE TRIM CODE
PLEASE RETURN TO HOME POSITION
PLEASE RETURN TO HOME POSITION
PLEASE CHANGE THE FEED AMOUNT OF ZIGZAG.
THE MISTAKE IS FOUND IN G DATA.
PLEASE REVIEW THE INPUT POINT.
EXCITATIONS OF THE MOTORS ARE RELEASED. MOVE THE CLAMP NEAR THE HOME
POSITION BY HAND, THEN PRESS THE ENTER ICON.
CHANGES OK ?
RAISE THE PRESSER FOOT (MATERIAL THICKNESS SETTING CAN BE DISPLAYED WHEN
PRESSER FOOT IS UP POSITION.)
SETTING VALUE OF MATERIAL THE THICKNESS IS OUT OF RANGE. PLEASE SET WITHIN
FOLLOWING RANGE.
MATERIAL STEP OF CURRENT SEWING DATA IS OUT OF THE FOLLOWING RANGE.
CONFIRM SETTING? YES:ENT, NO:X.
INPUTTED MATERIAL STEP VALUE IS OUT OF SETTING RANGE.
PLEASE SET WITHIN THE FOLLOWING RANGE
INPUTTED MATERIAL STEP VALUE IS OUT OF SETTING RANGE.
PLEASE SET WITHIN THE FOLLOWING RANGE
MATERIAL STEP OF CURRENT SEWING DATA IS OUT OF THICKNESS SETTING VALUE.
PLEASE MODIFY SEWING DATA.
PLEASE WAIT FOR A WHILE
ARE YOU SURE? Yes: ENTER ICON
SUB-MESSAGE
No: X ICON