Konica Minolta REGIUS 190 Service Manual page 181

4.4 Error Code
Error Error name
code
04037
Cassette Receive
Sensor NG (at ejec-
tion after elevation)
04041
Insertion shutter open
sensor NG
04042
Insertion shutter close
sensor NG
04061
Subscanning HP sen-
sor NG
04062 Absorption Detect
sensor NG (after lock
released)
04064
V-SYNC Sensor NG
04065 Absorption Detect
sensor NG (at retrac-
tion)
04066
Absorption Detect
sensor NG (at erase
completion)
04067
Absorption Detect
sensor NG (at erase
completion)
04068
Absorption Detect
sensor NG (at absorp-
tion point)
04069
Absorption Detect
sensor NG (before
erasure starts)
154
REGIUS MODEL 190 Service Manual Ver.1.00 2004.11.01
Error description
The elevation-bed cassette sen-
sor was ON following the comple-
tion of motion by the elevation bed
to the eject position during cas-
sette ejection.
A time-out occurred for ON detec-
tion by the open sensor during
opening operation by the insertion
slot shutter.
A time-out occurred for ON detec-
tion by the close sensor during
closing operation by the insertion
slot shutter.
A time-out occurred for ON detec-
tion by the HP sensor during HP
motion processing by the subscan-
ning section.
The back-plate Absorption Detect
sensor was OFF after the comple-
tion of lock release.
1) The V-SYNC sensor was
already ON before reading
operations started for subscan-
ning.
2) A limit-over occurred for ON
detection by the V-SYNC sen-
sor during read-operation pro-
cessing for subscanning.
The back-plate Absorption Detect
sensor was OFF after the comple-
tion of motion to the Escape Posi-
tion by the transport unit following
cassette separation.
The back-plate Absorption Detect
sensor was OFF after the comple-
tion of erasure in reading mode.
The back-plate absorption detect
sensor was OFF after the comple-
tion of erasure in reading mode.
The back-plate Absorption Detect
sensor was OFF after the comple-
tion of motion to the absorption
position by the transport unit fol-
lowing cassette peel-away.
The back-plate Absorption Detect
sensor was OFF before the start of
erasure in erase mode.
Action
Check MCB2:CN11-, pins 6 through 8
(Cassette Receive Sensor) and
MCB2:CN16 (Elevator Motor)
Check MCB2:CN10-, pins 11 through 13
(Insertion Shutter Open Sensor) and
MCB2:CN10, pins 3 and 4 (Shutter
Motor)
Check MCB2:CN10-, pins 14 through 16
(Insertion Shutter Close Sensor) and
MCB2:CN10, pins 3 and 4 (Shutter
Motor)
Check MCB2:CN5-, pins 16 through 18
(Scanning HP Sensor) and MCB2:CN6
(Subscan Motor)
Check MCB2:CN5-, pins 10 through 12
(Absorption Detect sensor)
Check MCB2:CN5-, pins 1 through 3 (V-
SYNC) and MCB2:CN6 (Subscan
Motor)
Check MCB2:CN5-, pins 10 through 12
(Absorption Detect sensor)
Check MCB2:CN5-, pins 10 through 12
(Absorption Detect sensor)
Check MCB2:CN5-, pins 10 through 12
(Absorption Detect sensor)
Check MCB2:CN5-, pins 10 through 12
(Absorption Detect sensor) and
MCB2:CN15 (Transportation Motor)
Check MCB2:CN5-, pins 10 through 12
(Absorption Detect sensor)