YOKOGAWA GX10 User Manual page 37

SRecDisp
Channel for Recording Display Data
Sets the channel for recording display data.
Syntax
SRecDisp,p1,p2,p3
p1 Number (see "Description")
p2 Channel type
Off Do not record display data.
IO I/O channel
Math Math channel
Communication channel
Com
p3 Channel number
Query
SRecDisp[,p1]?
Example Assign the display data of I/O channel 0005 to
number 10 and record.
SRecDisp,10,IO,0005
Description
• You cannot use this command to configure settings
while recording is in progress.
• You cannot use this command to configure settings
while computation is in progress.
• You cannot use this command to configure settings
when the measurement mode is set to dual interval.
• If p2=Off, you cannot set p3.
• There is a limit to the number of recording channels
depending on the recording interval
command).
Recording Number of Recording Channels
Interval
5 s/div 100
10 s/div 200
15 s/div or higher 500
For the large memory type (GX20-2/GP20-2/GM10-2),
the following table applies.
Recording Number of Recording Channels
Interval
When recording only
display data
5s/div 200
10s/div 500
15s/div 1000
30s/div or 1000
more
• You cannot set a channel more than once.
SRecEvent
Channel for Recording Event Data
Sets the channel for recording event data.
Syntax
SRecEvent,p1,p2,p3,p4
p1 Scan group (1 or 2)
p2 Number (see "Description")
p3 Channel type
Off Do not record event data.
IO I/O channel
Math Math channel
Com Communication channel
p4 Channel number
Query
SRecEvent[,p1[,p2]]?
Example Assign the event data of I/O channel 0006 to
number 11 and record.
SEventData,1,11,IO,0006
IM 04L51B01-17EN
Description
•
•
•
•
•
(SDispData
•
When recording display
data and event data
100
200
500
1000
•
•
•
You cannot use this command to configure settings
while recording is in progress.
You cannot use this command to configure settings
while computation is in progress.
If p3=Off, you cannot set p4.
This setting is valid when event data recording is
enabled (recording mode of the
There is a limit to the number of recording channels
depending on the recording interval
command).
Recording Number of Recording Channels
Interval
100 ms 100
200 ms 200
500 ms or more 500
For the large memory type (GX20-2/GP20-2/GM10-2),
the following table applies.
Recording Number of Recording Channels
Interval
When recording only
event data
100ms 500
200ms 500
500ms 1000
1s or more 1000
If the recording interval is 50 ms or less, there are
limits to the number of recording channels depending
on the model and measurement mode.
High speed0
Recording interval
Model 1ms 2ms 5ms
GX/GP10 2ch 4ch 10ch
GX/GP20-1 2ch 4ch 10ch
GX/GP20-2 10ch 20ch 50ch
GM10-1 2ch 4ch 10ch
GM10-2 10ch 20ch 50ch
Dual interval
Recording interval
Model 1ms 2ms 5ms
GX/GP10 - - 5ch
GX/GP20-1 - - 5ch
GX/GP20-2 5ch 10ch 25ch
GM10-1 - - 5ch
GM10-2 5ch 10ch 25ch
You cannot set a channel more than once.
When the measurement mode is set to dual interval and
p3 = IO, you can set the channels of only the applicable
scan groups.
If the measurement mode is set to dual interval, p3
= Math and p3 = Com can be specified only on scan
groups operating at the master scan interval.
2.4 Setting Commands
SMemory
command).
(SEventData
When recording display
data and event data
100
200
500
1000
10ms 20ms 50ms
20ch 40ch 100ch
20ch 40ch 100ch
100ch 150ch 150ch
20ch 40ch 100ch
100ch 150ch 150ch
10ms 20ms 50ms
10ch 20ch 50ch
10ch 20ch 50ch
40ch 50ch 50ch
10ch 20ch 50ch
40ch 50ch 50ch
2-19
1
2
App