H2: Multi-Function Digital Outputs - YASKAWA L1000A Technical Manual

5.7 H: Terminal Functions

◆ H2: Multi-Function Digital Outputs

H2-01 to H2-05: Terminals M1-M2, M3-M4, M5-M6, P1-C1, and P2-C2 Function Selection
■
The drive has five multi-function output terminals.
through H2-05.
No.
H2-01
H2-02
H2-03
H2-04
H2-05
Setting
0 During Run
1 Zero Speed
2 Speed Agree 1
3 User-set Speed Agree 1
4 Speed Detection 1
5 Speed Detection 2
6 Drive Ready (READY)
7 DC Bus Undervoltage
8 During Baseblock (N.O.)
9 Speed Reference Source
A Up/Down Command Source
B Torque Detection 1
E Fault
F Not used (Through Mode)
10 Minor Fault
11 Fault Reset Command Active
12 Timer Output
13 Speed Agree 2
14 User-set Speed Agree 2
15 Speed Detection 3
16 Speed Detection 4
18 Torque Detection 2
1A During Reverse
<1> Available in drive software PRG: 7017 or later.
Setting 0: During Run
Output closes when the drive is outputting a voltage.
Status
Open Drive is stopped.
Closed An Up/Down command is input or the drive is during deceleration or during DC injection.
Setting 1: Zero Speed
Terminal closes whenever the output speed or motor speed (CLV, CLV/PM) becomes less than the minimum output speed
set to E1-09 or S1-01.
Status
Open The operating speed is greater than the minimum output frequency (E1-09) or the zero speed level at stop (S1-01).
Closed The operating speed is less than or equal to the minimum output frequency (E1-09) or the zero speed level at stop (S1-01).
Note: When using CLV or CLV/PM control modes, the output terminal will close when the motor speed becomes less than or equal to
the zero speed level set for S1-01. In all other control modes, the output terminal will close when the output frequency becomes
less than or equal to the minimum output frequency set for E1-09.
208
Parameter Name
Terminals M1-M2 Function Selection
Terminals M3-M4 Function Selection
Terminals M5-M6 Function Selection
Terminals P1-C1 Function Selection (photocoupler)
Terminals P2-C2 Function Selection (photocoupler)
Table 5.12 Multi-Function Digital Output Terminal Settings
Function Page
Table 5.12 lists the functions available for these terminals using H2-01
Setting
208 1B During Baseblock 2 (N.C.)
208 1C Motor 2 Selection
209 1D During Regeneration
209 1E Restart Enabled
210 1F Motor Overload Alarm (oL1)
210 20 Drive Overheat Pre-alarm (oH)
211 2F Maintenance Period
211 30 During Torque Limit
211 33 Within Position Lock Bandwidth
211 37 During Frequency Output
211 50 Brake Control
211 47 Input Phase Loss
212 4E Braking Transistor Fault (rr)
212 51 Output Contactor Control
212 52 Door Zone Reached
212 53 Not Zero Speed
212 54 Light Load Direction
212 55 Light Load Direction Detection Status
212 58 Safe Disable Status
213 5C Motor Current Monitor
<1>
213 60 Internal Cooling Fan Alarm
211 61 Motor Pole Search Status
214 100 to 161 Functions 0 to 61 with Inverse Output
Description
Description
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
Setting Range
0 to 161 50: Brake control
0 to 161 51: Output control contactor
0 to 161 6: Drive ready
0 to 161 37: During frequency output
0 to 161 F: Through Mode
Function
Default
Page
214
214
215
215
215
215
215
215
215
215
216
216
216
216
216
216
216
216
216
216
216
216
217