O: Operator Related Parameters - YASKAWA L1000A Technical Manual

:
n9 Current Detection Adjustments
■
No. (Addr.) Name
n9-60
A/D Conversion Start Delay
(64DH)
<4> Default setting is determined by the drive model (o2-04).

◆ o: Operator Related Parameters

The o parameters set up the digital operator displays.
■ o1: Digital Operator Display Selection
For more details on the digital operator displays, refer to
No. (Addr.) Name
o1-01
(500H) Drive Mode Unit Monitor
Selection
o1-02
(501H) User Monitor Selection after
Power Up
o1-03 Digital Operator Display Unit
(502H) Selection
o1-04
V/f Pattern Setting Units
(503H)
o1-05
(504H)
LCD Contrast Control
o1-06
(517H) User Monitor Selection Mode
<44>
o1-07
(518H) Second Line Monitor Selection
<44>
o1-08
(519H) Third Line Monitor Selection
<44>
o1-10 User-Set Display Units Maximum
(520H) Value
o1-11 User-Set Display Units Decimal
(521H) Display
o1-12
Length Units
(739H)
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
Description
V/f OLV
Sets a delay time for starting the current signal A/D conversion. This value seldom needs to be
changed.
Digital Operator Display Unit Selection on page
Description
All Modes
Switches the display after the power has been turned on. When using an LED operator, pressing
the up arrow key will display the following data: frequency reference → rotational direction →
output frequency → output current → output voltage → U1-.
(This is done by entering the 1 part of U1-. Certain monitors are not available in some
control modes.)
All Modes
o1-02 selects the information that is displayed when the power is turned on.
1: Speed reference (U1-01)
2: Direction
3: Output speed (U1-02)
4: Output current (U1-03)
5: User-selected monitor (set by o1-01)
All Modes
Sets the units the drive should use to display the frequency reference and motor speed monitors.
0: 0.01 Hz
1: 0.01% (100% = E1-04)
2: r/min (calculated using the number of motor poles setting in E2-04, E4-04, or E5-04)
3: User-selected units (set by o1-10 and o1-11)
4: Elevator units 1 (speed in m/s, accel/decel rate and jerk in s)
5: Elevator units 2 (speed in m/s, accel/decel rate in m/s
6: Elevator units 3 (speed in ft/min, accel/decel rate in ft/s
V/f OLV
0: Hz
1: r/min
All Modes
Sets the brightness of the LCD operator (option).
All Modes
0: 3 Monitor Sequential (Displays the next 2 sequential monitors)
1: 3 Monitor Selectable (o1-07 and o1-08 selected monitor is displayed)
All Modes
Selects the monitor displayed on the second line.
All Modes
Selects the monitor displayed on the third line.
All Modes
These settings define the display values when o1-03 is set to 3.
o1-10 sets the display value that is equal to the maximum output frequency.
o1-11 sets the position of the decimal position.
V/f OLV
0: Millimeter unit
1: Inch unit
CLV CLV/PM
, jerk in m/s )
2 3
, jerk in ft/s )
2 3
CLV CLV/PM
CLV CLV/PM
B.3 Parameter Table
Setting Page
common_
Default:
<4>
TMonly
Min: 0.0 μs 248
Max: 40.0 μs
108.
Setting Page
common_
TMonly
Default: 106 (Monitor
U1-06)
249
Min: 105
Max: 699
common_
TMonly
Default: 1
Min: 1 249
Max: 5
common_
TMonly
Default: 1
Min: 0 249
Max: 6
<21>
common_
Default:
<5>
TMonly
Min: 0 250
Max: 1
Default: 3
common_
TMonly Min: 0 250
Max: 5
common_
Default: 0
TMonly
Min: 0 250
Max: 1
Default: 102
common_
TMonly Min: 101 250
Max: 699
Default: 103
common_
TMonly Min: 101 250
Max: 699
Default:
<20>
Min: 1 251
common_
TMonly
Max: 60000
Default:
<20>
Min: 0 251
Max: 3
common_
Default: 0
TMonly
Min: 0 251
Max: 1
B
421