F: Option Settings - YASKAWA L1000A Technical Manual

◆ F: Option Settings

F parameters are used to program the drive for Encoder and PG feedback from the motor and to function with option
cards.
F1: PG Speed Control Card
■
No.(Addr.) Name
F1-01
Encoder 1 Resolution
(380H)
F1-02 Operation Selection at PG Open
(381H) Circuit (PGo)
F1-03 Operation Selection at Overspeed
(382H) (oS)
F1-04
Operation Selection at Deviation
(383H)
F1-05 Encoder 1 Rotation Direction
(384H) Selection
F1-06 PG 1 Pulse Monitor Output
(385H) Division Ratio
F1-08
Overspeed Detection Level
(387H)
F1-09
Overspeed Detection Delay Time
(388H)
F1-10 Excessive Speed Deviation
(389H) Detection Level
F1-11 Excessive Speed Deviation
(38AH) Detection Delay Time
F1-14
PG Open-Circuit Detection Time
(38DH)
F1-18
dv3 Detection Selection
(3ADH)
F1-19
dv4 Detection Selection
(3AEH)
F1-20 PG Option Card Disconnect
(3B4H) Detection 1
F1-29
dEv Detection Condition Selection
(3BFH)
YASKAWA ELECTRIC SIEP C710616 38F YASKAWA AC Drive - L1000A Technical Manual
Description
V/f OLV
Sets the encoder resolution (number of pulses per revolution)
V/f OLV
0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
V/f OLV
0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
V/f OLV
0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
V/f OLV
0: A phase leads B in the up direction
1: B phase leads A in the up direction
V/f OLV
Sets the division ratio for the pulse monitor used of the PG option card installed to connector
CN5-C. By setting "xyz", the division ratio becomes = [(1 + x) / yz]. If only using the A pulse
for one track input, then the input ratio will be 1:1, regardless of what F1-06 is set to.
V/f OLV
Sets the overspeed detection level as a percentage of the maximum output frequency.
V/f OLV
Sets the time in seconds for an overspeed situation to trigger a fault (oS).
V/f OLV
Sets the speed deviation detection level as a percentage of the maximum output frequency.
V/f OLV
Sets the time in seconds for a speed deviation situation to trigger a fault (dEv).
V/f OLV
Sets the time required to trigger a PG Open fault (PGo).
V/f OLV
0: Disabled
n: Sets the number of dv3 situations that may be detected before triggering an actual dv3 fault.
V/f OLV
0: Disabled
n: Number of pulses that the A and B pulse are reversed that triggers dv4 detection.
V/f OLV
0: Disabled
1: Enabled
V/f OLV
Selects when DEV is active.
0: After speed reference, soft starter output and motor speed have matched once.
1: After speed reference and soft starter output have matched once.
2: Always during Run
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
CLV/PM
CLV
CLV CLV/PM
CLV CLV/PM
CLV CLV/PM
B.3 Parameter Table
Setting Page
Default:
<5>
common_
TMonly
Min: 1 ppr 195
Max: 60000 ppr
<34>
common_
TMonly
Default: 1
Min: 0 195
Max: 3
common_
TMonly
Default: 1
Min: 0 195
Max: 3
common_
TMonly
Default: 3
Min: 0 196
Max: 3
common_
Default:
<5>
TMonly
Min: 0 196
Max: 1
common_
TMonly
Default: 1
Min: 1 196
Max: 132
Default: 115%
common_
TMonly
Min: 0% 195
Max: 120%
Default: 0.0 s
common_
TMonly
Min: 0.0 s 195
Max: 2.0 s
Default: 10%
common_
TMonly
Min: 0% 196
Max: 50%
Default: 0.5 s
common_
TMonly
Min: 0.0 s 196
Max: 10.0 s
Default: 2.0 s
common_
TMonly Min: 0.0 s 195
Max: 10.0 s
common_
Default: 10
TMonly
Min: 0 196
Max: 10
common_
Default: 128
TMonly
Min: 0 197
Max: 5000
common_
Default: 1
TMonly
Min: 0 197
Max: 1
common_
TMonly
Default: 2
Min: 0 197
Max: 2
B
405