H2: Multi-Function Digital Outputs - YASKAWA L1000A Technical Manual

5.7 H: Terminal Functions
Setting 58: High speed limit down
When this input is closed the speed in down direction will be limited to the leveling speed. No speed limit is applied when
the car is going up.
Setting 5C: Stop Distance Correction
When this terminal closes and a direct landing is selected for the stopping method (S5-10 = 1), the drive will stop at the
designated floor with greater accuracy.
Setting 67: Communication test mode
The drive has a built-in function for self-diagnosing serial communications operation. The test involves wiring the send
and receive terminals of the RS-485/422 port together. The drive transmits data and then confirms that the
communications are received normally. Refer to
Setting 79: Brake feedback
This input allows the drive to monitor the brake operation and issue a fault if the brake status does not match the brake
command (digital output set to H2-

◆ H2: Multi-Function Digital Outputs

■
H2-01 to H2-05: Terminals M1-M2, M3-M4, M5-M6, P1-PC, and P1-P2 Function Selection
The drive has three multi-function output terminals.
01 through H2-05.
No.
H2-01 Terminals M1-M2 Function Selection
H2-02 Terminals M3-M4 Function Selection
H2-03 Terminals M5-M6 Function Selection
H2-04 Terminals P1-C1 Function Selection (photocoupler)
H2-05 Terminals P2-C2 Function Selection (photocoupler)
Setting
0 During Run
1 Zero Speed
2 Speed Agree 1
3 User-set Speed Agree 1
4 Speed Detection 1
5 Speed Detection 2
6 Drive Ready
7 DC Bus Undervoltage
8 During Baseblock (N.O.)
9 Speed Reference Source
A Up/Down Command Source
B Torque Detection 1
E Fault
F Not used (Through Mode)
10 Minor Fault
11 Fault Reset Command Active
12 Timer Output
13 Speed Agree 2
14 User-set Speed Agree 2
15 Speed Detection 3
16 Speed Detection 4
18 Torque Detection 2
188
Refer to Stop Distance on page 370
Self-Diagnostics on page 410
= 50).
Parameter Name
Table 5.12 Multi-Function Digital Output Terminal Settings
Function Page
189
189
189
190
190
190
191
191
191
191
191
192
192
192
192
192
192
192
193
193
193
192
for details.
Table 5.12 lists the functions available for theses terminals using H2-
Setting
1A During Reverse
1B During Baseblock 2 (N.C.)
1C Motor 2 Selection
1D During Regeneration
1E Restart Enabled
1F Motor Overload Alarm (oL1)
20 Drive Overheat Pre-alarm (oH)
2F Maintenance Period
30 During Torque Limit
33 Within Position Lock Bandwidth
37 During Frequency Output
50 Brake Control
51 Output Contactor Control
52 Door Zone Reached
53 Not Zero Speed
54 Light Load Direction
55 Light Load Direction Detection Status
56 Cooling Fan Status
57 Input Phase Loss
58 Safe Disable Status
61 Motor Pole Search Status
100 to 161 Functions 0 to 61 with Inverse Output
YASKAWA ELECTRIC SIEP C710616 38A YASKAWA AC Drive L1000A Technical Manual
for details on how to use this function.
Setting Range
0 to 161 50: Brake control
0 to 161 51: Output control contactor
0 to 161 6: Drive ready
0 to 161 37: During frequency output
0 to 161 F: Through Mode
Function
Default
Page
194
194
194
194
194
195
195
195
195
195
195
195
195
196
196
196
196
196
196
196
196
196