Page 2
The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPO- RATION is prohibited.
Page 4
ZXR10 8900 Series Command Reference (MPLS) mpls ldp router-id............28 mpls ldp style ...............30 mpls ldp target-session ..........30 mpls xconnect...............30 show mpls forwarding-table ..........31 show mpls l2transport binding.........32 show mpls l2transport vc..........33 show mpls label range............35 show mpls ldp backoff ............36 show mpls ldp bindings ..........37...
Page 5
.........80 ip rsvp authentication key passphrase ......81 ip rsvp authentication type ..........81 ip rsvp authentication window-size........82 ip rsvp bandwidth ............82 ip rsvp bfd ..............83 ip rsvp signalling hello (Global Configuration) ....84 Confidential and Proprietary Information of ZTE CORPORATION...
Page 6
ZXR10 8900 Series Command Reference (MPLS) ip rsvp signalling hello (Interface Configuration) ....84 ip rsvp signalling hello graceful-restart ......84 ip rsvp signalling hello graceful-restart refresh interval ..............85 ip rsvp signalling hello graceful-restart refresh misses ..85 ip rsvp signalling hello graceful-restart timers recovery-time ............86...
Page 7
........... 111 show ip rsvp hello instance detail........111 show ip rsvp hello instance summary ......112 show mpls traffic-eng fast-reroute ......... 113 show mpls traffic-eng interface........114 tunnel mpls traffic-eng fast-reroute........ 115 Confidential and Proprietary Information of ZTE CORPORATION...
Page 8
ZXR10 8900 Series Command Reference (MPLS) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
About This Manual Purpose This manual is ZXR10 8900 Series (V2.8.02.C) 10 Gigabit Rout- ing Switch Command Reference (MPLS) and applies to ZXR10 8902/8905/8908/8912 10 Gigabit routing switch. Intended This manual is intended for the following engineers: Audience � On-site maintenance engineers �...
Page 10
ZXR10 8900 Series Command Reference (MPLS) � ZXR10 8900 Series (V2.8.02.C) 10 Gigabit Routing Switch User Manual (MPLS) � ZXR10 8900 Series (V2.8.02.C) 10 Gigabit Routing Switch User Manual (DPI) � ZXR10 8900 Series (V2.8.02.C) 10 Gigabit Routing Switch User Manual (Firewall) �...
Reference includes 16 volumes. For details of each volume, please refer to preface of this manual. Commands in ZXR10 8900 Series (V2.8.02.C) 10G Routing Switch Command Reference (Index) are listed in sequence of from letter a to letter z and in form of table. Commands of all other volumes are classified and illustrated according to different function modules.
ZXR10 8900 Series Command Reference (MPLS) � Command format It describes the complete format of this command. If no for- mat is available, list it. � Parameter Description It describes parameters in this command in the form and pre- scribes the range and default value. If different products have different parameter ranges or default values, an additional form is used for description.
Use show history command in any mode, and the latest sev- eral commands in this mode will be listed. Command Modes The command modes in this manual are as follows: Confidential and Proprietary Information of ZTE CORPORATION...
Page 14
ZXR10 8900 Series Command Reference (MPLS) Modes Prompt Admis- Command Function sion to Enter the Mode Mode User ZXR10> Enter this View simple Mode mode directly information after logging onto system Privi- User enable Configure ZXR10# leged Mode system mode...
Page 15
OSPF protocol parameters router isis Configure IS-IS protocol parameters router bgp Configure BGP protocol parameters router Configure pimsm PIM-SM protocol parameters ipv6 router It configures RIPng parameters. ipv6 router It configures ospf OSPFv3 parameters. Confidential and Proprietary Information of ZTE CORPORATION...
Page 16
ZXR10 8900 Series Command Reference (MPLS) Modes Prompt Admis- Command Function sion to Enter the Mode Mode ZXR10(config- Global ip vrf Configure Config- vrf)# config- VRF protocol uration uration parameters Mode mode VFI con- ZXR10(config- Global It configures figu- vfi)#...
Page 17
Mode Mode IPSec ZXR10(config- Global ipsec It configures config- ipsec)# config- IPv6 IPSec uration uration protection. mode mode Diagno- Privi- diagnose It tests CPU ZXR10(diag)# sis mode leged utilization mode and memory utilization. Confidential and Proprietary Information of ZTE CORPORATION...
Page 18
ZXR10 8900 Series Command Reference (MPLS) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
.........40 show mpls ldp discovery.............41 show mpls interface ............42 show mpls ldp neighbor............42 show mpls ldp graceful-restart ..........44 show mpls ldp parameters ..........45 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) clear mpls ldp Purpose Use this command to reset the LDP router or its connection with some neighbor. Command Modes Privileged EXEC Syntax clear mpls ldp [neighbor <ip-address>] Syntax neighbor <ip-addre IP address of the neighbor, in the dotted Description ss>...
LDP to establish an LSP along a common hop-by-hop routing path. In addition, it is necessary to enable LDP on the interface to realize dynamic label switching on the interface. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) � Use the no form of this command to disable LDP to establish an LSP along a common hop-by-hop routing path no matter whether LDP is enabled on the interface or not. mpls ip(Interface...
Destination network to be filtered, basic ACL: Description st> 1~99 and 1000~1499 host-route-only Creates FEC only for the destination network (host address) with 32-bit mask Creates FEC for the specified route network obtained from BGP force Takes effect immediatedly Confidential and Proprietary Information of ZTE CORPORATION...
Page 24
ZXR10 8900 Series Command Reference (MPLS) Defaults LDP creates FEC for all destination networks except the route net- works obtained by BGP. Instructions � By default, LDP creates FEC for all destination networks except the route networks obtained by BGP. However, the number of networks may be so large that it needs to filter the network for which FEC need not be created ;...
In the case that there is no (prefix acl, peer acl) pair “applied to” the prefix, the label is not advertised to any neighbor if the no mpls ldp advertise-labels command is executed; otherwise, the label is advertised to all neigh- bors. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) iii. In the case that one (prefix acl, peer acl) pair “applied to” the prefix, the label is not advertised to any neighbor if prefix acl denies the prefix. iv. If prefix acl permits the prefix and there is no peer acl (namely none), the label is advertised to all neighbors.
Syntax mpls ldp backoff <initial-backoff><maximum-backoff> no mpls ldp backoff Syntax <initial-backoff> Initial backoff time in seconds, range: Description 10~65535, default: 15 seconds <maximum-backoff> Maximum backoff time in seconds, range: 10~65535, default: 120 seconds Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Instructions � The LDP session backoff reestablishment mechanism prevents two LSRs with incompatible configurations falling into the end- less cycle form the establishment of the session to the fail- ure. If the establishment of the session fails because of the...
LDP creates LDP dampening entities. configure the destination networks for which the LDP creates the LDP dampening entity. To disable this feature, use the no form of this command, and the no form of this command will take effect immediately. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Command Modes Global configuration Syntax mpls ldp dampening-acl {for <prefix-access-list>| force} no mpls ldp dampening-acl Syntax for <prefix-access-li Specifies which networks to be filtered. basic Description st> ACL: 1~99 and 1000~1499 force Takes effect immediately...
This example describes how to set the status holdtime as 100 sec- onds and the interval for sending hello messages as 20 seconds. ZXR10(config)#mpls ldp discovery targeted-hello holdtime 100 ZXR10(config)#mpls ldp discovery targeted-hello interval 20 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Related show mpls ldp parameter Commands mpls ldp discovery transport-address Purpose Use this command to configure the transmission address parame- ter carried in hello messages on the layer 3 interface. To disable this feature, use the no form of this command.
MPLS framework protocol. In this case, it is necessary to configure the egress control pol- icy to specify LDP to allocate popup labels to destination networks Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) flowing out of MPLS network, and make advertises to the upstream LSR. Thus upstream LSR will forward the traffic from the MPLS net- work in the form of IP packets (or explicitly popup label packets).
2. This example describes how to advertise explicit null labels to the directly connected network 137.5.0.0, and advertise im- plicit null labels to other directly connected networks. ZXR10(config)#mpls ldp explicit-null for 10 ZXR10(config)#ip access-list standard 10 ZXR10(config-std-nacl)#permit 137.5.0.0 0.0.255.255 ZXR10(config-std-nacl)#deny any ZXR10(config-ext-nacl)# Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) mpls ldp graceful-restart Purpose Use this command to enable the router to support LDP Graceful restart function. Command Modes Global configuration Syntax mpls ldp graceful-restart [timer {max-recovery <interval>| neighbor-liveness <interval>}] no mpls ldp graceful-restart [timer {max-recovery | neighb...
Example This example describes how to establish a session with a neighbor whose TCP connection address is 140.2.1.15 by using abcdefg as the MD5 authentication key. ZXR10(config)#mpls ldp neighbor 140.2.1.15 password abcdefg Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) mpls ldp request-labels Purpose Use this command to configure the prefix and downstream neigh- bors for which LDP sends request messages. To disable this fea- ture, use the no form of this command. Command Modes...
Page 39
MPLS forwarding related with the bounding of these labels. Example This example describes how to specify the IP address of the inter- face fei_1/1 as the router identifier. ZXR10(config)#mpls ldp router-id fei_1/1 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Related show mpls ldp discovery commands mpls ldp style Purpose Ue this command to adopt a new keepalive mechanism of LDP sessions. Once a hello packet is received, reset the keepalive time of the session this hello packet maintains.
ZXR10(config-if)#mpls xconnect 1.1.1.1 100 mtu 1504 Configure VPWS which uses static PW: ZXR10(config-if)#mpls xconnect static-pw 1.1.1.1 test 100 Related show mpls l2transport binding Commands show mpls forwarding-table Command This checks LIB. Function Command Modes All Modes Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Command format show mpls forwarding-table [<prefix>[{<mask>|<mask-len >}]] Parameter Parameter Description Description <prefix> This is prefix of destination address. <mask> This is mask of destination address prefix. <mask-len> This is length of mask of destination address prefix, in range of 1~32.
Purpose Use this command to check the VC information transmitted at Layer 2. Command Modes All modes Syntax show mpls l2transport vc [{vcid <vcidmin>[<vcidmax>]| interface <interface-name>[<loca-lcircuit-id1>[<local-circuit-id 2>]]| destination <ip-addr>}][detail] Confidential and Proprietary Information of ZTE CORPORATION...
Page 44
ZXR10 8900 Series Command Reference (MPLS) Syntax vcid Shows information based on vcid Description <vcidmin> Lower limit of the designated vcid or the designated vcid range, it is must be specified if there is the parameter vcid specified. range: 1~4294967295 <vcidmax>...
Maximum transmission unit Remote interface Description of the remote interface description bounded with VPWS Sequencing Sequencing function show mpls label range Purpose Use this command to show the label range that LDP can use. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Command Modes User EXEC and privileged EXEC Syntax show mpls label range [detail] Syntax detail Shows detailed information of labels Description Example This example shows the output of the show mpls label range command.
66.66.0.66:0, label: 16 remote binding: lsr: 144.0.0.44:0, label: imp-null 66.66.0.66/255.255.255.255 local binding: label: 20 remote binding: lsr: 155.0.0.55:0, label: 19 remote binding: lsr: 66.66.0.66:0, label: imp-null(inuse) remote binding: lsr: 144.0.0.44:0, label: 18 103.0.0.0/255.0.0.0 Confidential and Proprietary Information of ZTE CORPORATION...
Page 48
ZXR10 8900 Series Command Reference (MPLS) local binding: label: imp-null 155.0.0.55/255.255.255.255 local binding: label: 25 remote binding: lsr: 155.0.0.55:0, label: imp-null(inuse) remote binding: lsr: 144.0.0.44:0, label: 24 remote binding: lsr: 66.66.0.66:0, label: 24 2. This example describes how to show label bindings of the net- work 166.0.0.0 and its subnets learned by the LSR 144.0.0.44.
The displayed field descriptions are shown below. Field Description The LSP is suppressed InLable Ingress label OutLable Egress Label Network NetworkIP address and mask length of LSP From LDP Router identifier of the remote neighbor Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Field Description Reuse Time from the last time to receiving packets to now Penalty Penalty value. Values of LSP reuse and suppression are decided by this value show mpls ldp flap-statistics summary Purpose Use this command to show dampening information of LSP in LDP flapping routes.
Src IP addr Source address of hello messages sent from neighbors Transport IP addr Transmission address of the TCP connection indicated by neighbor IP addr Transmission address of the TCP connection indicated by neighbor Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) show mpls interface Purpose Use this command to show the interface on which LDP is enabled. Command Modes User EXEC and privileged EXEC Syntax show mpls interface [<interface-name>] Syntax <interface-name> Interface name Description Instructions If there is no parameter after this command , it shows complete information of the interface where LDP is enabled.
Page 53
Up time Period when the session is in the current state LDP discovery Adjacent relationship list maintaining the sources session interface Interface where the adjacency relation is created Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Field Description Src IP addr Source IP address of peer hello messages which establish the adjacency relationship holdtime Holdtime when the adjacency relationship does not receive hello messages hello interval Interval for sending hello messages...
Setting of basic discovery parameters Downstream on Reserved version upgrading Demand max hop count LDP initial/maximum Setting of parameters for the LDP session backoff backoff reestablishment mechanism LDP loop detection Reserved version upgrading Confidential and Proprietary Information of ZTE CORPORATION...
Page 56
ZXR10 8900 Series Command Reference (MPLS) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
Use this command to set the description about a VRF. Delete the description with the no form of this command. Command Modes VRF configuration Syntax description <string> no description Syntax <string> Description about the VRF, a string of 1~16 Description characters Confidential and Proprietary Information of ZTE CORPORATION...
There is no route map related to the VRF by default. Example This example describes how to set the import route map related to the VPN named zte. The name of the route map is inmap. ZXR10(config)#ip vrf zte ZXR10(config-vrf)#import map inmap...
VPN. � Enter the VRF configuration mode after the command is exe- cuted successfully. Example This example describes how to configure a VPN named zte. ZXR10(config)#ip vrf zte ZXR10(config-vrf)# ip vrf forwarding Purpose Use this command to associate an interface with a VRF. Cancel the association with the no form of this command.
ZXR10 8900 Series Command Reference (MPLS) maximum routes Purpose Use this command to control the number of routes entering VRF and give the related alarm. Command Modes VRF configuration Syntax maximum routes limit {warn threshold | warn-only} no maximum routes...
There is no route distinguisher by default. Instructions The VRF does not take effect until the route distinguisher is con- figured. Examples This example describes how to configure an route distinguisher for the VPN named zte. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) ZXR10(config)#ip vrf zte ZXR10(config-vrf)#rd 1:1 route-target Purpose Use this command to create route-target extended community at- tribute related to the VRF. Delete the attribute with the no com- mand. Command Modes VRF configuration Syntax route-target [import | export | both]<extended-community>...
Use this command to show the route information of VPN instances. Command Modes All modes Syntax show ip route vpn Example This example describes how to show the route information of all VPN instances. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) ZXR10#show ip route vpn show ip route vrf Purpose Use this command to show the VRF route information. Command Modes All modes Syntax show ip route vrf <vrf-name>[network <ip-address>[mask <net-mask>]] Syntax <vrf-name> VRF name, a string of 1~16 characters Description network <ip-addre...
Command Modes Interface configuration Syntax tunnel checksum no tunnel checksum Example This example describes how to configure local GRE tunnel to enable the tunnel checksum option. ZXR10(config)#interface fei_5/1 ZXR10(config-if)#tunnel checksum Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) tunnel destination Purpose Use this command to configure a destination address for the tun- nel. Cancel the configuration with the no form of this command. Command Modes Interface configuration Syntax tunnel destination {ipv4 | ipv6}<ip-address>...
Source IP address or IPv6 address of the Description tunnel Example This example describes how to set the source address of the tunnel as 10.10.10.1. ZXR10(config)#interface fei_2/1 ZXR10(config-if)#tunnel source ipv4 10.10.10.1 History Command tunnel source <ip-address> Confidential and Proprietary Information of ZTE CORPORATION...
Page 68
ZXR10 8900 Series Command Reference (MPLS) This command is expressed before the platform version v4.6.01. The keywords ipv4 and ipv6 are provided after the platform ver- sion v4.6.01. Confidential and Proprietary Information of ZTE CORPORATION...
Description statistic) corresponds to Instructions Clera VPLS flow statistics information by force. Only ZXR10 6900 and ZXR10 8900 support this command. Example This example describes how to clear vfi1 and all vfi flow. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) ZXR10#clear flowstat vpls vfi vfi1 ZXR10#clear flowstat vpls Related show mac-table Commands clear flowstat vpws Purpose Use this command to clear the flow statistics information to which VPWS corresponds. Command Modes Privileged EXEC Syntax clear flowstat vpws vcid <vcid>...
Use this command to configure a pair of addresses of other PEs and the vcid in a static multi-hop pseudo-wire S-PE instance, and establish pseudo-wires. Delete the established pseudo-wires with the no form of this command. Command Modes VFI configuration and CFI MSPW configuration Confidential and Proprietary Information of ZTE CORPORATION...
Page 72
ZXR10 8900 Series Command Reference (MPLS) Syntax For VFI configuration mode, peer <peer-ip-address>[spoke][tunnel <tunnel-number>] no peer <peer-ip-address> For VFI MSPW configuration mode, peer <peer-ip-address> vcid <vcid> no peer <peer-ip-address> Syntax <peer-ip-address> IP address of the peer PE, in general it is the...
Use this command to specify the type of a pseudo-wire established by the VPLS instance. Use this command to specify the type of a pseudo-wire in a static multi-hop pseudo-wire S-PE configuration instance. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Command Modes] VFI configuration or VFI MSPW configuration Syntax pwtype {ethernet | ethernet-vlan} Syntax ethernet | Pseudo-wire type: Ethernet or Ethernet-vlan Description ethernet-vlan Instructions This command is supported after the platform version 4.6.02. When a pseudo-wire is established between two PEs, there must be the negotiation about the type of the pseudo-wire established.
0000.0000.3005 1.1.1.1 fei_7/5 dynamic 0000.0000.3004 1.1.1.1 fei_7/5 dynamic The displayed field descriptions are shown below. Field Description MAC address peer-address Peer address, namely the remote address outIntLab Inner outgoing label outExtLab Outer outgoing label Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Field Description outInterface Outgoing interface type MAC address type, statically configured or dynamically learned Related clear mac-table vfi Commands show mpls l2transport vc vpls Purpose Use this command to display information about the pseudo-wire successfully established .
This example describes how to show the number of L2VPNs con- figured on the router. ZXR10#show mpls l2transport vpn summary The summary information about configured l2 vpn: vpn_type current/max vpws 0/1501 vpls 3/4096 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Related show mpls l2transport vc vpls Commands show vfi Purpose Use this command to show detailed information about some virtual forwarding instance (VFI). Command Modes User EXEC and privileged EXEC Syntax show vfi <vfi-name>...
Syntax stp-tunnel enable no stp-tunnel enable Syntax enable Enables STP tunnel in vfi. Description Instructions The platform version 4.8.22 and upgrade versions support this command. Use this command to set VPLS stp tunnel. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Example This example describes how to set stp tunnel in vfi. ZXR10(config-vfi)#stp-tunnel enable Related no vfi Commands pwtype peer no peer vpls mac-filter vcid Purpose Use this command to specify a virtual channel identifier (VCID) for the VPLS instance.
The virtual forwarding instances (VFIs) with the same virtual channel identifier (VCID) on different PEs belong to the same VPLS and they can communicate with each other. After this command is executed, enter the VFI configuration mode. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Example This example describes how to configure a name for the VPLS in- stance on the PE. ZXR10(config)#vfi vfi1 ZXR10(config-vfi)# Related no vfi Commands pwtype peer no peer vfi mspw Purpose Use this command to configure the multi-hop static pseudo wire (PW) S-PE.
This command is provided only for ZXR10 GER and ZXR10 T64E/T128. Example This example describes how to configure a VLAN range in PE VFI interface configuration mode. ZXR10(config)#vfi vfi1 ZXR10(config-vfi)#vlan range 1 10 80 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Related no vlan range Commands xconnect vfi Purpose Use this command to add local interface to a virtual forwarding instance (VFI). Cancel the setting with the no form of this com- mand. Command Modes...
1 enable 2 enable To show line card in slot 2 currently configured with VPLS cross- card forwarding function, execute the following command: ZXR10(config)#show fa vpls config slot 2 slot vpls 2 enable Confidential and Proprietary Information of ZTE CORPORATION...
Page 86
ZXR10 8900 Series Command Reference (MPLS) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...
........96 show mpls traffic-eng ds-te te-class ........97 show mpls traffic-eng autoroute ..........98 show mpls traffic-eng interface detail ........98 show mpls traffic-eng interface packet-counter......99 show mpls traffic-eng tunnels..........100 Confidential and Proprietary Information of ZTE CORPORATION...
Disable this function with the no form of this command. Command Modes Interface configuration Syntax ip rsvp authentication challenge no ip rsvp authentication challenge Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Defaults The behavior of this command is disabled on the interface by de- fault. Instructions � This command is an optional command. � This command is supported after the platform version 4.8.21. Example This example describes how to enable challenge mechanism on the interface fei_1/1.
Use this command to configure RSVP authentication type (MD5 or SHA1). Restore the default type MD5 with the no form of this command. Command Modes Interface configuration Syntax ip rsvp authentication type {md5 | sha1} no ip rsvp authentication type Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Syntax MD5 authentication type Description sha1 SHA1 authentication type Defaults MD5 authentication type is adopted on the interface by default. � Instructions This command is an optional command. � This command is supported after the platform version 4.8.21.
Forwarding Detection (BFD) sessions are not established even if this command is configured. Example This example describes how to configure Bidirectional Forwarding Detection (BFD) function on the interface. ZXR10(config)#interface fei_1/1 ZXR10(config-if)#ip rsvp bfd Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) ip rsvp signalling hello (Global Configuration) Command This enables MPLS traffic engineering on local device. Function Command Modes Global configuration mode Command format ip rsvp signalling hello no ip rsvp signalling hello Default MPLS traffic engineering is disabled by default.
Restore the default value with the no form of this command. Command Modes Global configuration Syntax ip rsvp signalling hello graceful-restart refresh misses < msg-count > no ip rsvp signalling hello graceful-restart refresh misses Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Syntax < msg-count > Number of the missing hello packets, range: Description 4~10 Defaults The default missing number is 4. Example This example describes how to configure the number of missing graceful restart hello packets as 3.
(30 seconds) by default, in range of 5000~65535000. Example To configure the interval of MPLS traffic engineering sending re- fresh packets to 60000 milliseconds, execute the following com- mand: ZXR10(config)#ip rsvp signaling refresh interval 60000 Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) ip rsvp signalling refresh interval (Interface Configuration) Command This command is used to configure the interval of sending refresh Function packets. By executing command no, default interval is reset. Command Modes Interface configuration mode Command format ip rsvp signalling refresh interval <interval-value>...
Use the command no to clear the configuration. Command Mode Global Configuration Mode Syntax mpls traffic-eng ds-te no mpls traffic-eng ds-te Defaults Disable DSTE function by default. Instructions V4.8.20 and its later versions support this command. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Example This example shows how to enable DSTE function at global config- uration mode. ZXR10T64(config)#mpls traffic-eng ds-te mpls traffic-eng ds-te bc-mode Purpose Use this command to configure BC mode of DSTE. Use command no to delete this configuration.
07 < ctype > classtype configured by user, the range is 01 Defaults By default, TE-CLASS mapping is as follows: TE-CLASS CType Priority — — — — Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) TE-CLASS CType Priority — — — — Example This example shows how to configure TE-CLASS mapping relation- ship: teclass1 corresponds the combination of ct0 and priority1. ZXR10(config)#mpls traffic-eng ds-te te-classes te-class 1 class-type 0 priority 1...
MPLS traffic engineering signalling request and floods its resource information through IGP. Example This example describes how to enable MPLS TE signalling on the interface. ZXR10(config)#interface fei_3/1 ZXR10config-if)#mpls traffic-eng tunnels Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) show ip rsvp authentication Purpose Use this command to show the status and configuration informa- tion of all security assistants (SAs) or some neighbor. Command Modes All modes except User EXEC Syntax show ip rsvp authentication [<A.B.C.D >] Syntax <A.B.C.D>...
Instructions This command is supported after the platform version 4.8.01. Example The following contents will be shown after using this command. ZXR10#show ip rsvp hello graceful-restart Graceful Restart: Enabled Refresh interval: 10000 msecs Confidential and Proprietary Information of ZTE CORPORATION...
1 0 1 2 unused 3 unused 4 0 0 5 1 0 6 unused 7 unused Description of Displayed Information: Description Information ExpTeclassId the value of TE-CLASS CType CType of tunnel Priority Tunnel priority Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) show mpls traffic-eng autoroute Purpose Use this command to show the status and configuration informa- tion of all tunnels with automatic routes. Command Modes All modes except user EXEC Syntax show mpls traffic-eng autoroute Instructions This command is supported after the platform version 4.8.20.
Number of LSPs which take the interface as the incoming interface show mpls traffic-eng interface packet-counter Command This shows detailed information about the number of RSVP packets Function on interface. Command Modes All modes except user mode Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Command format show mpls traffic-eng interface packet-counter [<interface- name>] Parameter Parameter Description Description <interface-name> This is a locally configured interface with RSVP TE function. Default This command shows the detailed information about the number Configuration of packets on the interface configured with RSVP TE function.
Page 111
Tunnel signalling state: down/connected/sig- nalling Path option Explicit path configuration Bandwidth Reserved tunnel bandwidth Priority Priority for establishing and holding the tunnel Affinity Tunnel affinity Fast-reroute Whether the tunnel supports fast reroute: enable/disable Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Field Description InLabel Incoming label and the interface of the tunnel OutLabel Outgoing label and the interface of the tunnel Source address of the tunnel Destination address of the tunnel Tun_Id Tunnel identifier Tun_Instance...
Purpose Use this command to configure the metric type and value of the tunnel automatic route. Disable this function with the no form of this command. Command Modes Tunnel interface configuration Confidential and Proprietary Information of ZTE CORPORATION...
The following contents will be shown after using this command. ZXR10#show mpls traffic-eng tunnels summary Signalling Summary: LSP Tunnels Process: running RSVP Process: Forwarding: enabled Head:6 interfaces,2 active signalling attempts,2 established Midpoints:0,Tails: 64 The descriptions of the displayed information are shown below. Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Field Description LSP Tunnels Process LSP tunnel state RSVP Process RSVP protocol state Forwarding Forwarding state Head Statistic information of local tunnel interface Number of tunnels in MPLS traffic engineering active signalling Number of tunnels successfully established...
Command This command is used to configure tunnel priority on tunnel port Function of local device. Command no can be used to disable this function. Command Modes Tunnel interface configuration mode Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Command format tunnel mpls traffic-eng priority <setup_prirority><holdup-pri ority> no tunnel mpls traffic-eng priority Parameter Parameter Description Description <setup_prirority> This is setup priority of tunnel. <holdup-priority> This is holdup priority of tunnel. Default The default priority of interface is 7.
Purpose Use this command to configure the time interval for the interface to send RSVP hello requests. Command Modes Interface configuration Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Syntax ip rsvp signalling hello refresh interval <interval> no ip rsvp signalling hello refresh interval Syntax <interval> Time interval in seconds, range: 10~30000, Description default: 100 seconds Instructions � This command is supported after the platform version 4.6.02.
V4.6.02 and its later versions support this command. Example To show example information (the following instance is only for reference), execute the following command: ZXR10#show ip rsvp hello instance detail Neighbor 200.1.1.1 Source 200.1.1.2 Hello globally enabled State:UP Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) Type:respond to request I/F: Eth1/1 LSP protectiong:0 Refresh Interval(msec) Configured:100 Src_instance 0Xa9f07c13 , Dst_instance 0X9BBAA407 Description of displayed fields: Field Description neighbor This is neighbor IP address. source This is the IP address of node sending hello request packet.
Label: the label value advertised by the next hop at the intermediate node Status FRR current state: ready or active Prefix Address for labels to forward packets by LSP identifier LSP identifier, including source address, tunnel identidier and lsp identifier Confidential and Proprietary Information of ZTE CORPORATION...
ZXR10 8900 Series Command Reference (MPLS) show mpls traffic-eng interface Purpose Use this command to display information about interfaces where RSVP traffic engineering is enbaled. Command Modes All mods except user EXEC Syntax show mpls traffic-eng interface [<interface-name >] Syntax...
The tunnel supports Fast ReRoute (FRR) and informs the down- stream node that it needs local protection. The downstream node tries its best to offer local protection and sends related information to the head node if local protection is available. Confidential and Proprietary Information of ZTE CORPORATION...