Busch-Jaeger SD/U12.55.11-825 Manual page 9

8.18.42
8.18.43
8.18.44
8.18.45
8.18.46
8.18.47
8.18.48
8.18.49
8.18.50
8.18.51
8.18.52
8.18.53
8.18.54
8.18.55
8.18.56
8.18.57
8.18.58
8.18.59
8.18.60
8.18.61
8.18.62
8.18.63
8.18.64
8.18.65
8.18.66
8.18.67
8.18.68
8.18.69
8.18.70
8.18.71
8.18.72
8.18.73
8.18.74
8.18.75
8.18.76
8.18.77
8.18.78
8.18.79
8.18.80
8.18.81
8.18.82
8.18.83
8.18.84
8.18.85
8.18.86
8.18.87
8.18.88
8.18.89
8.18.90
8.18.91
8.18.92
Product manual 2CKA001473B5472
Basic stage cooling - Cyclic sending of the control value ........................................................189
Basic stage cooling - Hysteresis .............................................................................................189
Basic stage cooling - PWM cycle cooling (min) .......................................................................189
Basic stage cooling - Maximum control value (0 - 255) ...........................................................190
Basic stage cooling - Minimum control value for basic load (0 to 255) ....................................190
Control of additional cooling stage ............................................................................................191
Control of additional cooling stage - Control value type .............................................................191
Control of additional cooling stage - Cooling type ...................................................................191
Control of additional cooling stage - P-component ..................................................................192
Control of additional cooling stage - I-component ...................................................................192
Control of additional cooling stage - Temperature difference to basic stage..............................192
Control of additional cooling stage - Extended settings ...........................................................193
Additional cooling stage ............................................................................................................193
Additional cooling stage - Mode of the control value ...............................................................193
Additional stage cooling - PWM cycle cooling (min) ................................................................193
Additional cooling stage - Control value difference for sending of cooling control value ..........194
Additional cooling stage - Cyclic sending of the control value .................................................194
Additional cooling stage - Maximum control value (0 - 255) ....................................................194
Additional cooling stage - Minimum control value for basic load (0 - 255) ...............................195
Additional cooling stage - Hysteresis ......................................................................................195
Settings of basic load ................................................................................................................196
Settings of basic load - Minimum control value for basic load > 0 ...........................................196
Basic load settings - Basic load active when controller is off ...................................................196
Combined heating and cooling modes ......................................................................................197
Combined heating and cooling modes - Switchover of heating/cooling ...................................197
Combined heating and cooling modes - Operating mode after reset ......................................197
Combined heating and cooling modes - Heating/cooling control value output ........................197
Combined heating and cooling modes - Additional heating/cooling stage control value
output ........................................................................................................................................198
Setpoint settings ........................................................................................................................199
Setpoint settings - Setpoint for heating comfort = setpoint for cooling comfort ........................199
Setpoint settings - Setpoint for standby and Eco are absolute values .......................................199
Setpoint settings - Hysteresis for switchover heating/cooling ....................................................199
Setpoint settings - Setpoint for heating and cooling comfort ...................................................200
Setpoint settings - Setpoint for heating comfort .......................................................................200
Setpoint settings - Setpoint for heating standby ......................................................................200
Setpoint settings - Reduction for standby heating by ..............................................................200
Setpoint settings - Setpoint for heating economy ....................................................................200
Setpoint settings - Reduction for heating economy by ............................................................201
Setpoint settings - Setpoint for heating building protection ......................................................201
Setpoint settings - Setpoint for cooling comfort .......................................................................202
Setpoint settings - Setpoint for cooling standby ......................................................................202
Setpoint settings - Increase for cooling standby by .................................................................202
Setpoint settings - Setpoint for cooling economy ....................................................................202
Setpoint settings - Increase for cooling economy ....................................................................202
Setpoint settings - Setpoint for cooling building protection ......................................................203
Setpoint settings - Setpoint setting via communication object (DPT 9.001).............................203
Setpoint settings - Display.......................................................................................................203
Setpoint settings - Hide temperature unit ..................................................................................203
Setpoint settings - Send current setpoint ................................................................................204
Setpoint settings - Cyclic sending of the current setpoint ..........................................................204
Setpoint settings - Basic set value is .........................................................................................204
Table of contents
│9