Stratasys J3 Series User Manual page 2

Copyright
DOC-19001 Revision G
Copyright © 2006–2022 Stratasys Ltd. All rights reserved.
This documentation contains proprietary information of Stratasys Ltd. This information is supplied solely to assist
authorized users of Stratasys J3 Series 3D printing systems. No part of this document may be used for other purposes.
The specifications on which this document is based are subject to change without notice.
Trademarks
Stratasys, PolyJet, J35, J3, GrabCAD Print, GrabCAD PolyJet Server, FullCure, Agilus30, Digital ABS, Vero,
VeroBlack, VeroClear, VeroUltra, RGD810, RGD820, SUP710, and WSS150 are trademarks of Stratasys Ltd. and/or
its subsidiaries or affiliates and may be registered in certain jurisdictions. All other product names and trademarks are
the property of their respective owners.
Open Source Software Licenses
AustinHarris.JsonRpc (https://raw.githubusercontent.com/Astn/JSON-RPC.NET/), licensed under the MIT license
(https://raw.githubusercontent.com/Astn/JSON-RPC.NET/master/LICENSE)
AvalonEdit (http://avalonedit.net/), licensed under the MIT license (https://opensource.org/licenses/MIT)
ControlzEx (https://raw.githubusercontent.com/ControlzEx/ControlzEx/), licensed under the MIT license
(https://raw.githubusercontent.com/ControlzEx/ControlzEx/master/LICENSE)
Gong-wpf-dragdrop (https://github.com/punker76/gong-wpf-dragdrop/), licensed under the BSD 3-Clause license
(https://github.com/punker76/gong-wpf-dragdrop/blob/dev/LICENSE)
Newtonsoft.Json (https://raw.githubusercontent.com/JamesNK/Newtonsoft.Json), licensed under the MIT license
(https://raw.githubusercontent.com/JamesNK/Newtonsoft.Json/master/LICENSE)
Nlog (https://github.com/NLog/NLog/tree/master), licensed under the BSD 3-Clause license
(https://github.com/NLog/NLog/blob/master/LICENSE.txt)
QT 5.9 (https://doc-snapshots.qt.io/qt5-5.9/index.html), licensed under the GNU Lesser General Public License
(LGPL) version 3 (https://doc-snapshots.qt.io/qt5-5.9/licensing.html)
RhinoMocks (http://hibernatingrhinos.com/oss/rhino-mocks), licensed under the BSD 2-Clause license
(https://opensource.org/licenses/bsd-license.php)
SQLite.CodeFirst (https://github.com/msallin/SQLiteCodeFirst), licensed under the Apache license 2.0
(https://github.com/msallin/SQLiteCodeFirst/blob/master/LICENSE)
Yajl (https://lloyd.github.io/yajl/), licensed under the ISC license (https://lloyd.github.io/yajl/)
FCC Compliance
The equipment referred to in this guide has been tested and found to comply with the limits for a Class A device
pursuant to part 15 of the FCC rules. These limits provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. Stratasys 3D printing systems generate, use and can radiate
radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his own expense.
The 3D printer referred to in this guide contains a transmitter module, FCC ID YH6-DUPCAB.
NOTE: Stratasys is not responsible for radio or TV interference caused by unauthorized modification to this equipment.
Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the
equipment.
Stratasys contact information is available from the
DOC-19001 Rev. G
Stratasys Support Center.