Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Stratasys J826
Summary of Contents for Stratasys J826
- Page 1 Site Preparation Guide Stratasys J826 3D Printing System DOC-18005 Rev. E...
- Page 2 No part of this document may be photocopied, reproduced, or translated into any human or computer language in any form, nor stored in a database or retrieval system, without prior permission in writing from Stratasys. This document may be printed for internal use only. All copies, shall contain a full copy of this copyright notice.
-
Page 3: Table Of Contents
Local Area Network Telephone Environmental Conditions Temperature and Humidity Air Quality Noise Level Accessories and Utilities Start-Up Kit Exhaust Adapter Compressed Air Fire Safety Equipment Materials Handling and Storage Printing Materials © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. - Page 4 Cleaning Solvent Site Preparation Checklist © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved.
-
Page 5: Introduction
About this Guide The information and requirements provided in this document ensure proper installation and operation of the Stratasys J826 printing system. The customer is responsible for preparing the site as described in this document, and according to any applicable local regulations. -
Page 6: Physical Description
Stratasys J826 Physical Description Physical Description The Stratasys J826 printing systems consist of the following main components: • printer • material cabinet • printer computer (built into the printer) • client workstation provided by the customer Figure 1 Stratasys J826 printer... -
Page 7: Shipment And Delivery
Shipment and Delivery Shipping Information and Customer Responsibility Shipment to the customer will be arranged by a Stratasys distributor as indicated in the “ship to” part of the invoice.The customer is responsible for providing detailed delivery information, including, whether or not there is loading dock at the delivery site. -
Page 8: Unloading
Minimum space requirements for unloading the printer are shown in the figure below. Figure 2 Unloading dimensions—top view Note: Dimensions are shown in centimeters. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. - Page 9 Stratasys J826 Shipment and Delivery Figure 3 Printer center of gravity © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved.
-
Page 10: Installation Area
The following is a sample floor plan, showing the 3D printing system—the printer, the materials cabinet, and the workstation. The dimensions shown in the figure are the minimum clearance requirements. Figure 4 Printer floor plan (sample, not to scale) © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. -
Page 11: Workstation Requirements
Stratasys J826 Workstation Requirements Workstation Requirements To view the specifications for client workstations, go to: http://help.grabcad.com/print/system- requirements. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. -
Page 12: Electrical Requirements
220–240 VAC, 50–60 Hz, 7 A , 1 phase Printer short circuit rating: 1000 A If the power at the facility does not support the above specifications, contact your Stratasys specialist. Important: The diagram below shows the required connection to the power socket. Make sure that the electrician sees this before installing the printer. -
Page 13: Circuit Breaker
• the printer computers can perform a “graceful shutdown” in the event of a power failure. The UPS specifications are listed below. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. - Page 14 UPS units that only connect to a serial communication port are not suitable. Command-line control is necessary for the UPS software to execute a script in the printer software when shutting down. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved.
-
Page 15: Communication Lines
Figure 6 Network installation The connection to the local network should be established prior to printer installation. Telephone A telephone near the printer is recommended for general communication and service calls. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. -
Page 16: Environmental Conditions
Otherwise, the room ventilation system should change the air at least four times every hour. Noise Level The noise level around the printer is typically less than65 dB during printing. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. -
Page 17: Accessories And Utilities
4 in (100 mm) 106 cfm (3 m /min) 134 cfm (3.8 m /min) Figure 7 Printer exhaust system It is recommended to install an eyewash station near the printer, for emergency use. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. -
Page 18: Compressed Air
A gas-based fire extinguisher is recommended in case of fire in or near the system. Some other fire extinguishers are also acceptable, but liquid fire extinguishers should not be used. Contact local fire authorities for specific recommendations. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. -
Page 19: Materials Handling And Storage
One liter of isopropanol (IPA) or ethanol (ethyl alcohol) should be available at all times for cleaning purposes. The customer is responsible for ensuring that the material storage area complies with local regulations. © DOC-18005 Rev. E 2019-2020 Stratasys. All rights reserved. - Page 20 Stratasys J826 Site Preparation Checklist Site Preparation Checklist A checklist is provided by your Stratasys representative listing all of the tasks described in this document. Fill in the information requested in the checklist, and submit it to your Stratasys representative. An installation date will be scheduled after the checklist has been approved by Stratasys.
- Page 21 www.stratasys.com THE 3D PRINTING SOLUTIONS COMPANY ISO 9001:2008 Certified...
Need help?
Do you have a question about the J826 and is the answer not in the manual?
Questions and answers