Mitsubishi Electric MELSERVO-J2S Series Transition Handbook page 300

Part 7: Common Reference Material
MR-J2S-_A_
No. Name
49 Output signal selection 1
MR-J4-_A_
Type Target No. Type
PD28 Hex
PD23 Hex
PD24 Hex
Hex _ X_ _
PD27 Hex
PD26 Hex
PD28 Hex
PD23 Hex
PD24 Hex
Hex _ _ X _
PD27 Hex
PD26 Hex
Hex _ _ _X -
Hex: hexadecimal parameter; Dec: decimal parameter
7 - 61
Target
BWNG (battery warning) signal assignment will
be converted.
(1) When the setting value of No. 49 is _ 1 _ _
_ _ XX
(CN1A-19), the setting value of PD28 will be
converted to _ _ 09 (CN1-49 pin setting).
(2) Only when the setting value of No. 1 is _ 0 _
_ (CN1B-18 is the initial value ALM), this
parameter will be converted.
When the setting value of No. 49 is _ 2 _ _
(CN1B-18), the setting value of PD27 will be
_ _ XX
converted to _ _ 09.
(3) When the setting value of No. 49 is _ 3 _ _
(CN1A-18), the setting value of PD23 will be
converted to _ _ 09 (CN1-22 pin setting).
(4) Only when the setting value of No. 1 is _ _ 0
_ (CN1B-19 is the initial value ZSP), this
parameter will be converted.
_ _ XX
When the setting value of No. 49 is _ 4 _ _
(CN1B-19), the setting value of PD24 will be
converted to _ _ 09 (CN1-23 pin setting).
(5) When the setting value of No. 49 is _ 5 _ _
(CN1B-6), the setting value of PD26 will be
converted to _ _ 09 (CN1-25 pin setting).
_ _ XX
Otherwise, the initial value will be set.
When conversion of I/O signal assignment is
enabled, these parameters will be converted
according to the control signal connection of
the renewal tool.
When conversion of I/O signal assignment is
not enabled, the initial value will be used.
_ _ XX
This parameter can be used with MR
Configurator2 of software version 1.53F or
later.
WNG (warning) signal assignment will be
converted.
(1) When the setting value of No. 49 is _ _ 1 _
_ _ XX
(CN1A-19), the setting value of PD28 will be
converted to _ _ 08 (CN1-49 pin setting).
(2) Only when the setting value of No. 1 is _ 0 _
_ (CN1B-18 is the initial value ALM), this
parameter will be converted.
When the setting value of No. 49 is _ _ 2 _
(CN1B-18), the setting value of PD27 will be
_ _ XX
converted to _ _ 08.
(3) When the setting value of No. 49 is _ _ 3 _
(CN1A-18), the setting value of PD23 will be
converted to _ _ 08 (CN1-22 pin setting).
(4) Only when the setting value of No. 1 is _ _ 0
_ (CN1B-19 is the initial value ZSP), this
parameter will be converted.
_ _ XX
When the setting value of No. 49 is _ _ 4 _
(CN1B-19), the setting value of PD24 will be
converted to _ _ 08 (CN1-23 pin setting).
(5) When the setting value of No. 49 is _ _ 5 _
(CN1B-6), the setting value of PD26 will be
converted to _ _ 08 (CN1-25 pin setting).
_ _ XX
Otherwise, the initial value will be set.
When conversion of I/O signal assignment is
enabled, these parameters will be converted
according to the control signal connection of
the renewal tool.
When conversion of I/O signal assignment is
not enabled, the initial value will be used.
_ _ XX
This parameter can be used with MR
Configurator2 of software version 1.53F or
later.
The setting value will not be maintained.
- -
(Alarm code output setting)
Conversion rule