Information On Specific Jumbo; Cbj-Home - Linak Inline LA20 User Manual

7. Information on specific JUMBO

1. CBJ-Home (MEDLINE CARELINE
®
Recommendations
• If emergency stop is pressed whilst charging, the batteries will not be charged .
• When charging, the CBJ Home will not be able to operate any actuators .
• For recharging the batteries, use charger CH01 (charger has to be ordered separately) .
• Note: Always mount the CBJ Home with the channel sockets facing downwards .
• The CBJ Home is not intended for use with "buffer" type actuators such as LA28 .
• The actuator must always be fitted with an exchangeable cable (mini-fit) socket .
• Actuators on channel 1 must always be with spline .
• The mains cables must always be ordered separately when ordering a CBJ with an internal charger .
• Use only original LINAK mains cables to ensure proper connection to internal charger .
• Always use fully charged batteries for learning mode procedures .
• Only an authorised LINAK service centre should change a battery in a CBJ Home . If a CBJ Home is opened and a battery is changed by unauthorised
personnel, there may be a risk of malfunction .
• When using the control box with emergency stop button, the stop button must be released before charging batteries or before the application is put
into operation .
• It cannot be guaranteed that the actuator will stop exactly at the weight that is stored as the motors in the actuators will use less current when run
in . Though it will never reach the 1 .5 times max . load as the norm states .
• Tolerance for current cut off is: +/-10 %
• The maximum cut-off value that can be registered (stored) is 8 Amp .
• If an actuator or CBJ Home is exchanged it will be necessary to reset the max . load to ensure the correct cut-off value for the new system as a whole .
• The registration function can only be activated by using a specially produced hand control (HB7X161-00) . A standard hand control cannot activate
the function .
• To operate the "Learn mode" function in External charger versions produced before February 2010 press the "R" button when "learning" (the lifting
arm actuator will operate automatically) . With all other versions (and future versions with external charger) both the "R" button and the "lifting arm"
button need to be pressed .
• It is possible to use the "learn mode" function for channel 2: To operate the learn mode function for channel 2, press the "R" button and the "leg".
spread out" button at the same time . Run actuator with load and full cycle to record maximum current during a cycle .
Warning
• In order to avoid injury, the emergency stop should be activated in (all) transport situations .
• When "learn mode" is used, and channel 2 is pressed instead of channel 1, the CBJ Home will learn a new current limit of nearly 0 Amp .
This will make it impossible to run the actuator with channel 2 until a new learn mode has been programmed .
Mounting information:
The CBJ-Home is mounted by means of 2 screws:
Type ISO4762-M6x90-8 .8 ( not supplied by LINAK )
Spares information:
The cable lock kit consists of the following 3 items:
• 2 x screws
• 1 x blind plug for ch . 2 if not in use
• Cable Lock
All the cable lock items are included when ordering the kit, article number: 0898001-B .
The mounting screws for the control box and the charger must be tightened with a maximum torque of 1 Nm .
TM
)
®
Page 203 of 295
The CBJ-Home is a specially developed solution for patient lifts . The
complete system consists of a control box and a battery enclosed in a single
elegant module .
The system is approved according to medical safety standards and contains
a series of features ensuring a safe comfortable lift, e .g . the CBJ-Home
is equipped with a soft-start function, electrical emergency lowering,
emergency stop etc .
Usage
• CBJ Home with internal charger: Nominal current draw max . 280 mA
Power consumption (standby) max . 1 .3 W
Power consumption (charging) max . 12 W
• Duty cycle: Max . 10 % or 2 min . continuous use then 18 min . without use
• Ambient temperature: + 5 °C to + 40 °C
• Storage temperature: - 10 °C to + 50 °C
• Relative humidity: 20% to 80% - non-condensing
• Atmospheric pressure: 700 to 1060 hPa
• Height above sea level: Max . 3000 meters
• Approvals: IEC60601-1, ANSI/AAMI ES60601