Etl Marking; Mounting - Linak Inline LA20 User Manual

ETL marking

Due to space limitations, the complete ETL marking demands are not represented on the marking plates .
The full ETL recognised component markings are shown here:
C/N 120690
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
C/N 9901916
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
C/N 4008003
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1

Mounting

Actuator:
Do not use any other screws for the mounting brackets than those recommended by LINAK
the inner parts of the actuator . This will result in an irregular operation or even damage the actuator .
During mounting, the actuator must always be:
• Fixed to protect it against torque and bending . See Figure 2 on the next page.
• Fixed so that it is restrained, but free to move on its mountings . See Figure 3 on the next page.
• Fixed in brackets, which can take up the torque reaction . See Figure 3 on the next page.
• Mounted at right angles so that the right angle requirement is observed . See Figure 4 on the next page.
• Mounted with correct bolt dimension .
• Mounted with bolts and nuts made of high quality steel grade (for example 10 .8) . No thread on bolts inside the back fixture or the piston rod eye .
• Bolts and nuts must be protected from being able to fall out .
• Inspect the actuator for damage before mounting . A damaged actuator must not be mounted . Check for instance for damaged packaging .
• Do not use a too high tourque when mounting the bolts for the back fixture or the piston rod eye
Control boxes:
• The mounting screws on the control box must be tightened with a maximum torque of 1 Nm
• The mounting surface to which the control box is attached should have a surface evenness better than ± 0 .5 mm .
• Systems must not be installed/deinstalled while in operation .
• Control boxes with a wet alarm must be mounted as shown on figure 5 on the next page .
• Nuts and bolts must be made of steel .
• Nuts and bolts must be tightened securely .
• For control boxes with earth connection (Class 1), the nut must be tightened with a torque of 1 - 1 .2 Nm .
Cables:
It is important to remove the transport plastic bag before using the cable .
Accessories:
The mounting screws on accessories must be tightened with a maximum torque of 1 Nm
• The mounting surface to which the accessory is attached should have a surface evenness of more than ± 0 .5 mm
• Systems must not be installed/deinstalled while in operation
• Nuts and bolts must be made of steel
• Nuts and bolts must be tightened securely
Controls:
The mounting screws on the controls must be tightened with a maximum torque of 1 Nm
• The mounting surface to which the accessory is attached should have a surface evenness of more than ± 0 .5 mm
• Systems must not be installed/deinstalled while in operation
• Nuts and bolts must be made of steel
• Nuts and bolts must be tightened securely
For further instructions regarding mounting, see the data sheet for the individual product or in chapter 5, 6 or 8
in this manual.
C/N 4008004
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
C/N 4008005
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
C/N 4008623
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
. If longer screws are used, they will come into contact with
®
Page 19 of 295
C/N 4008838
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
C/N 4008671
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1
C/N 4009507
Conforms to ANSI/AAMI Std . ES60601-1
Cert . to CSA Std . C22 .2 No . 60601-1