Xerox WorkCentre 5022 Service Manual page 528

Chain-
Link NVM Name
690-435 FAXBOX_CTC_NUMBER
690-436 FAXBOX_T5_TIMER
690-437 FAXBOX_RTN_PERCENT
690-438 FAXBOX_EXTEND_DIS_DTC
690-439 FAXBOX_DROP_OUT_TIMER
690-440 FAXBOX_RX_RESOLUTION
690-441 FAXBOX_DATA_FORMAT
690-450 FAXBOX_V34_MODEM_PERMITTED
690-451 FAXBOX_V34_SYMBOL_RATE
690-452 FAXBOX_V34_FIRST_TX_SPEED
690-453 FAXBOX_V34_SYMBOL_ENABLE
690-454 FAXBOX_V34_CTRL_BIT_RATE
690-455 FAXBOX_V34_ANSAM_PHASE_REVERSAL 1
690-456 FAXBOX_V8_TE_TIME
690-457 FAXBOX_V34_CC_TIMER
690-458 FAXBOX_V34_SHIFT_G3
690-459 FAXBOX_ANSAM_SEND_TIME
690-460 FAXBOX_ANSAM_START_TIME
690-461 FAXBOX_V34_GAIN_CHANGE
690-462 FAXBOX_V34_FLAME
690-470 FAXBOX_NT_PAUSE_DURATION
690-471 FAXBOX_PBX_SELECTION_ENABLED
General
6.3.21 NVM FAX
Table 1 FAX
Setting Setting
Range Range Write
(Minimu (Maximu Default Allowed/
m Value) m Value) Value Protected
0 15 13 O
60 60 60 X
0 100 10 O
0 0 0 X
6 6 6 X
0 4 4 O
0 3 3 O
0 1 1 O
1 5 5 O
1 14 14 O
0 255 240 O
0 0 0 X
1 1 X
10 10 10 O
35 35 35 X
0 0 0 X
4 4 4 X
2 2 2 X
1 1 1 X
0 1 0 O
0 255 *1 O
0 255 3 O
06/2014
6-100
Default
Value
Yes/No Description
O The number of ECM/CTC sends for Fax Job.
X The RNR signal timer (seconds) (fixed value) for Fax Job.
60 = 60 s
O The Send Reference of RTN Command (%) (proportion) for Fax Job.
X The number of DIS/DTC FIF send bytes (fixed value) for Fax Job.
0 = Auto
X The image information receive dropout monitoring timer value (seconds)
(fixed value) for Fax Job. 6 = 6 seconds.
O The resolution specification during receive for Fax Job.
0 = STD, 1 = STD + FINE, 4 = S-FINE
O The Encoding Method (send/receive) for Fax Job.
0 = T30_MH, 1 = T30_MR, 2 = T30_MMR, 3 = T30_JBIG
O The V34 capability for Fax Job.
0 = OFF, 1 = ON
O The max. permissible value of symbol speed for Fax Job.
1 = 2400, 2 = 2800, 3 = 3000, 4 = 3200, 5 = 3429
O The max. value of bit speed for Fax Job.
1=2400,2=4800,3=7200,-,12=28800,13=31200,14=33600
O The enable instruction of symbol speed for Fax Job.
(When 0 to 15 is set, this is not in use).
X The control channel bit speed (fixed value) for Fax Job.
0 = 1200 bps
X The ANSam phase reversal (fixed value) for Fax Job.
1 = Reverse
O The V8 Te time (100 ms) (fixed value) for Fax Job.
10 = 1000 ms
X The timeout time from V34 mode (Phase 2) to control channel (seconds)
(fixed value) for Fax Job.
35 = 35 s
X The G3 mode transition at V34 CC timeout (fixed value) for Fax Job.
0 = Do not transition
X The ANSam signal max. send time (seconds) (fixed value) for Fax Job.
4 = 4 s
X The time from line close to ANSam send (seconds) (fixed value) for Fax
Job. 2 = 2 seconds.
X The V34 receive gain switching (fixed value) for Fax Job.
1 = Perform
O The V34 1 frame size for Fax Job.
0=256, 1=64
O The pause time (100 ms) for Fax Job.
O The public network selection Send Signals time (seconds) for Fax Job.
Version 1.0
WC 5022/5024