Table of Contents
Advertisement
Command
INPut
:FILTer
[:LPASs]
:FREQuency <cutoff_freq>,(@<ch_list>)
:FREQuency? (@<channel>)
[:STATe] ON | OFF, (@<channel>)
[:STATe]? (@<channel>)
:GAIN <chan_gain>,(@<ch_list>)
:GAIN? (@<channel>)
:LOW <wvolt_type>,(@<ch_list>)
:LOW? (@<channel>)
:POLarity NORmal | INVerted,(@<ch_list>)
:POLarity? (@<channel>)
MEMory
:VME
:ADDRess <mem_address>
:ADDRess?
:SIZE <mem_size>
:SIZE?
:STATe 1 | 0 | ON | OFF
:STATe?
OUTPut
:CURRent
:AMPLitude <amplitude>,(@<ch_list>)
:AMPLitude? (@<channel>)
:STATe ON | OFF,(@<ch_list>)
:STATe? (@<channel>)
:POLarity NORmal | INVerted,(@<ch_list>)
:POLarity? (@<channel>)
:SHUNt ON | OFF,(@<ch_list>)
:SHUNt? (@<channel>)
:TTLTrg
:SOURce FTRigger | LIMit | SCPlugon | TRIGger
:SOURce?
:TTLTrg<n>
[:STATe] ON | OFF
[:STATe]?
:TYPE PASSive | ACTive,(@<ch_list>)
:TYPE? (@<channel>)
:VOLTage
:AMPLitude <amplitude>,(@<ch_list>)
:AMPLitude? (@<channel>)
ROUTe
:SEQuence
:DEFine? AIN | AOUT | DIN | DOUT
:POINts? AIN | AOUT | DIN | DOUT
SAMPle
:TIMer <num_samples>,(@<ch_list>)
:TIMer? (@<channel>)
Chapter 6
SCPI Command Quick Reference
Control filter Signal Conditioning Plug-ons
Sets the cutoff frequency for active filter SCPs
Returns the cutoff frequency for the channel specified
Turn filtering OFF (pass through) or ON (filter)
Return state of SCP filters
Set gain for amplifier-per-channel SCP
Returns the channel's gain setting
Controls the connection of input LO on a Strain Bridge (Opt. 21 SCP)
Returns the LO connection for the Strain Bridge at channel
Sets input polarity on a digital SCP channel
Returns digital polarity currently set for <channel
Specify address of VME memory card to be used as reading storage
Returns address of VME memory card
Specify number of bytes of VME memory to be used to store readings
Returns number of VME memory bytes allocate to reading storage
Enable or disable reading storage in VME memory at INIT
Returns state of VME memory, 1=enabled, 0=disabled
Set amplitude of Current Source SCP channels
Returns the setting of the Current Source SCP channel
Enable or disable the Current Source SCP channels
Returns the state of the Current Source SCP channel
Sets output polarity on a digital SCP channel
Returns digital polarity currently set for <channel>
Adds shunt resistance to leg of Bridge Completion SCP channels
Returns the state of the shunt resistor on Bridge Completion SCP channel
Sets the internal trigger source that can drive the VXIbus TTLTrg lines
Returns the source of TTLTrg drive.
When module triggered, source a VXIbus trigger on TTLTrg<n>
Returns whether the TTL trigger line specified by n is enabled
sets the output drive type for a digital channel
Returns the output drive type for <channel>
Sets the voltage amplitude on Voltage Output and Strain SCPs
Returns the voltage amplitude setting
Returns comma separated list of channels in analog I, O, dig I, O ch lists
Returns number of channels defined in above lists.
Sets number of samples that will be made on channels in <ch_list>
Returns number of samples that will be made on channels in <ch_list>
Command Quick Reference
Description
HP E1415 Command Reference
299
Advertisement
Table of Contents
