Normal Operating Conditions - IDEC MICROSmart FC6A Series User Manual

2: P
RODUCT
This chapter describes the part names and specifications of the modules that make up the FC6A Series MICROSmart.
Various types of modules are available for the FC6A Series MICROSmart. These include the CPU modules (All-in-One CPU module,
CAN J1939 All-in-One CPU module, and Plus CPU module), digital I/O modules (digital input modules, digital output modules, and
digital mixed I/O modules), analog I/O modules (analog input modules, analog output modules, and analog mixed I/O modules),
PID modules, communication modules, expansion interface modules (expander and remote master/slave), HMI modules, cartridge
base modules, and cartridges (digital I/O cartridges, analog I/O cartridges, and communication cartridges).

Normal Operating Conditions

The normal operating conditions common to the modules are as follows.
Ambient Operating Temperature
Expanded Ambient Operating Temperature
Ambient Storage Temperature
Relative Humidity
Storage Humidity
Pollution Degree
Degree of Protection
Atmosphere
Altitude or Air Pressure
Installation Location
Device Class
Overvoltage Category
Vibration Resistance
Shock Resistance
EMC Immunity
*1 The HMI module (FC6A-PH1) is 0 to 55°C.
*2 For the status of support for expanded ambient operating temperatures in each product, see "Status of Support for Expanded Ambient
Operating Temperatures (-25 to -10°C and 55 to 65°C)" on page 2-2. Certain products are also unable to support expanded ambient operating
temperatures, depending on the product version. Check the product version number before using the product in expanded ambient operating
temperatures.
The product ratings and usage conditions of certain models will also change if used in expanded ambient operating temperatures. For details,
see the following sections.
"Ambient Temperature, Input Voltage, Output Voltage, I/O Simultaneous ON Ratio" (Pages 2-30, 2-63, 2-71, 2-73, 2-83, 2-85, 2-87, 2-99, 2-

100)
"Ambient Temperature and Analog Input/Output Restrictions" (Page 2-115)

"Rating at Max Surrounding Air Temperature of 55°C/65°C" (Page 2-186)

"Connection Restrictions When Expanding the PLC" (Page 3-37)

Checking the Version Number
The version number of each module is listed on the side of the module. The performance and functionality of the analog I/O
module will differ by its version, so check the version number before use.
The version number on a CPU module is HV*** and the version number on other modules is V***.
S
PECIFICATIONS
-10 to +55°C
-25 to -10°C, +55 to +65°C
-25 to +70°C (no freezing)
10 to 95%, no condensation
10 to 95%, no condensation
2 (IEC60664-1)
IP20 (IEC60529)
No corrosive gas
1,013 to 795 hPa (0 to 2,000 m) during operation
1,013 to 701 hPa (0 to 3,000 m) during transport
Inside cabinet
Open equipment
II
DIN Rail Mounted
5 to 8.4 Hz half amplitude 3.5 mm, 8.4 to 150 Hz, acceleration 9.8 m/s
direction XYZ, 2 hours (IEC/EN 61131-2)
Panel Mounted
147 m/s
IEC/EN61131-2, Zone B compatibility
S/N:XXXXX-XXXXX
FC6A S MICROS
ERIES
*1
(no freezing)
*2
(no freezing)
2
(15 G), 11 ms, XYZ, 3 axes, 6 directions, 3 times each (IEC 61131-2)
V100
Version Number
U ' M FC9Y-B1722
MART SER S ANUAL
2
(1 G), each
2-1