Xerox WorkCentre Pro 423 Service Manual page 40

WorkCentre Pro 423/428
Status Status Description
Code
H8-68 Page Memory PAGE MEMORY PWB R/W
(4868) failure Error (Initialization error)
HDD Failure Hard Disk NOT Ready
HD-01
(4D01)
HD-02 HDD Failure Hard Disk Self Diag error
(4D02)
HD-03 HDD Failure Hard Disk commanc error
(4D03)
HD-10 HDD Failure Hard Disk format error
(4D04)
HD-11 HDD Failure Short of effective space on
(4D11) hard disk
HD-71 Hard Disk Initial communication check
(4071) Interface Error error between MCU/SW
PWB and I Hard Disk
HD-72 Hard Disk Framing/ Overrun/Parity
(4072) Interface Error error between MCU/SW
PWB and I Hard Disk
HD-73 Hard Disk BCC error between
(4073) Interface Error MCU/SW PWB and I Hard
Disk
HD-74 Hard Disk No Communication between
(4074) Interface Error MCU/SW PWB and I Hard
Disk
HD-75 Hard Disk Communication not
(4075) Interface Error established between MCU/
SW PWB and I Hard Disk
E1-1 JAM at REGI REGI SENSOR not OFF
(4E11) SNR within specified time
E1-2 JAM at REGI FUSER EXIT SENSOR not
(4E12) SNR ON within specified time
after REGI SENSOR OFF
E1-6 JAM at REGI Paper remaining on REGI
(4E14) SNR SENSOR
2-8
03/02
Corrective Ref.
Action BSD
POWER 3.1C
OFF/ON
3.1C
POWER
OFF/ON
POWER 3.1C
OFF/ON
POWER 3.1C
OFF/ON
POWER 3.1C
OFF/ON
Execute Chain
15-Function
POWER 3.1C
OFF/ON
POWER 3.1C
OFF/ON Check
connectors.
POWER 3.1C
OFF/ON
POWER 3.1C
OFF/ON
POWER 3.1C
OFF/ON
POWER 3.1C
OFF/ON Check
connectors.
Remove paper. 8.5
Remove paper. 8.5,10.
3
Remove paper. 8.5
Status Status Description
Code
E3-1 JAM at FUSER FUSER EXIT SENSOR not
(4E31) OFF within specified time
E3-6 JAM at FUSER Paper remaining on FUSER
(4E36) EXIT SENSOR
E5-1 IOT Interlock RIGHT HAND COVER is
(4E51) Open open
E5-2 IOT Interlock FRONT COVER is open
(4E52) Open
E6-1 CABINET CABINET RIGHT HAND
(4E61) Interlock Open COVER is open
E8-2 JAM at DUPLEX DUPLEX SENSOR not ON
(4E82) within specified time
C1-3 TRAY1 misfeed REGI SENSOR not ON
(4C13) within specified time after
feed start
C2-2 TRAY2 misfeed T/A ROLL2 SENSOR not
(4C22) ON within specified time
after feed start
C2-3 TRAY2 misfeed REGI SENSOR not ON
(4C23) within specified time after
T/A ROLL2 SENSOR ON
C3-1 TRAY3 misfeed T/A ROLL3 SENSOR not
(4C31) ON within specified time
after feed start
C3-2 TRAY3 misfeed T/A ROLL2 SENSOR not
(4C32) ON within specified time
after T/A ROLL3 SENSOR
ON
C3-3 TRAY3 misfeed REGI SENSOR not ON
(4C33) within specified time after
T/A ROLL2 SENSOR ON
C4-1 TRAY4 misfeed T/A ROLL3 SENSOR not
(4C41) ON within specified time
after feed start
C4-2 TRAY4 misfeed T/A ROLL2 SENSOR not
(4C42) ON within specified after
T/A ROLL3 SENSOR ON
CHAPTER 2 TROUBLESHOOTING
2.3 Level 2 Troubleshooting
Corrective Ref.
Action BSD
Remove paper. 10.3,10
.5
Remove paper. 10.3
Close the Cover. 1.7A
Close the Cover. 1.7A
Close the Cover. 1.7B
Remove paper. 10.4
Remove paper. 8.1,8.5
Set TRAY1.
Remove paper. 8.1,8.3,
Set TRAY2.
8.4
Remove paper.
8.4,8.5
Remove paper. 8.1,8.4
Set TRAY3.
Remove paper. 8.3,8.4
Remove paper.
8.3,8.4
Remove paper. 8.1,8.4
Set TRAY4.
Remove paper. 8.3,8.4