Mode Set - Xerox WorkCentre Pro 423 Service Manual

2.4.9.9 Mode set

Chain Functio
n
50 1 Printing after detecting Toner Empty
50 6 MSI installed (auto detection)
50 7 FACE UP TRAY installed
50 9 90-Degree Rotation installed
50 10 DUPLEX installed
50 11 OCT installed (auto detection)
50 20 FUSER OVER TEMP disabled
50 22 Automatically disable copying job (CP/CF/CFP)
50 23 Darkness at Auto selection (copy darkness)
50 24 Warm-up Time Setting for Cold Area (All Tray)
50 26 Auto interruption of printer job
50 28 MAIN MOTOR speed adjustment
50 29 Adjustment of Toner Empty Warning detection
50 30 Adjustment of Toner Empty detection
50 31 MC type
50 33 Number of paper trays installed
50 36 DADF is installed
50 37 Printer KIT is installed
50 39 Switcher is installed
50 40 Page memory feature installed
50 41 DADF Stamp installed
50 42 Front exposure control
50 44 MSI A4/LETTER size switchover
50 45 Tray 1 paper type
50 46 Tray 2 paper type
50 47 Tray 3 paper type
WorkCentre Pro 423/428
Item Min. value
0
0
0
0
0
0
0
4
1
0
0
0
5
0.5
20
2 sec.
0
2
0
0
0
0
0
0
0
0
0
0
Default Max. value Amount Adjustment
of change
1 1
- 1
0 1
- 1
- 1
- 1
0 1
10 99 1 min.
3 5
0 60 1 sec.
10 99 1 min.
11 21 0.1%
23 40 0.1 sec.
2.3 sec. 4 sec.
160 200 0.1 sec.
16 sec. 20 sec.
1
3
2
1
1
2
1
0 1
0 1
0 2
0 2
0 2
03/02
2-171
Remarks
0:On 1:Off (By selecting "Off", the M/C cycles down
after sensing.)
0:No 1:Yes by hard copy (reading out only)
0:No 1:Yes
0:No(without PGM) 1:Yes(with PGM)
0:No 1:Yes by hard copy (reading out only)
0:No 1:Yes
0:Disabled 1:Generated
0:Disable 4 to 99:4 to 99min.
1:Dark 2:Dark a little 3:Normal 4:Light a little 5:Light
0:Disable 1-60:1 to 60 sec.(Adjustment at IOT
condensation)
0:Disable 4-99:4 to 99 min.
0:DC model 1:MF model
2:3 trays 3:4 trays (If tray 4 enabled, auto detected
after restart)
0:No 2:DADF By hardcopy (reading out only)
0:No 1:Yes By hardcopy (reading out only)
0:No 1:Yes By hardcopy (reading out only)
0:No 1:A4 2:A3By hardcopy (reading out only)
0:No 1:Yes By hardcopy (reading out only)
0:No 1:Yes
0:A4 1:LETTER
0: plain paper, 1: transparency, 2: thick paper
0: plain paper, 1: transparency, 2: thick paper
0: plain paper, 1: transparency, 2: thick paper
How to use the Diagnostic C/E Mode
CHAPTER 2 TROUBLESHOOTING