Xerox WorkCentre Pro 423 Service Manual page 236

WorkCentre Pro 423/428
Chain Function Item
58 555 Number of speed dials available
58 558 Resending for Send Fault documents by
pressing the Stop button.
58 559 Resending of Send Fault documents
58 560 Relay broadcast capability
58 563 Remote sort copy reception capability
58 565 Handling of the same destination at speed
dial registration
58 566 DTMF(PB) detection capability (for DTMF
I/F)
58 567 Setting remote reception and key
detection count
58 568 Broadcast/Multi-Poll type
58 570 Start time of operating status hours
58 572 End time of operating status hours
58 574 Accessibility to Private Mail Box from
remote terminal using DTMF/IF
58 576 Password for the DTMF Relay Broadcast
Operation
58 581 System data for forced calculation of
accounting data (data for abbreviated
number)
2-204
03/02
Description Default
0 to 65535 200:with MMB-A 200
installed
500:with MMB-B installed
0:Off 1:On 00
0:Off 1:On 00
0:Off 1:On(TOKI method) 02
2:On(Mashu method)
0:Off 1:On 01
0: Enable registration of the same 01
address 1: Disable registration of
the same address
0:Off 1:On 01
0 to 15time(1step=1 time) 00
0:One by one 1:Simultaneously 01
2:Disabled
0 to 23 hr 08
0 to 23 hr 20
0:Off 1:On 01
00 to 99 00
0:ISDN charge to be applied 01
1:ISDN charge to be ignored
CHAPTER 2 TROUBLESHOOTING
How to use the Diagnostic C/E Mode
Description
When the operator presses the Stop button during send operation, the
document will be handled as a Send Fault job. This data determines
whether or not to resend the job.
Determines whether the documents not sent and stored in memory
should be resent as enabled by operator. When "On" is selected, check
that "1" (auto deleted in 24 hrs) is set up in Chain=058 and Function=356
(Handling of documents not sent) and explain to the customer that the
documents will be deleted in 24 hrs.
Determines whether or not to enable the Relay Broadcast capability.
When "Off" is selected, NSF signal will be set to "Not function" to inform
the transmitter as such.
1. The transmission side can specify the number of copies (up to 99) to
the reception side to output the specified number of copies by multi-
copying. (Setting at shipping from factory: 2 copies)
2. The number of copies can be specified to Able 3321N/3221N/1321N
Series, Able 3300/1300 Series, Able 3010/3011/3015/3016, and
7030/7033 Telecopier.
Determines whether or not to enable various features using DTMF.
(Relay Broadcast or Mail Box)
Determines how the Broadcast and Multi-Poll operation should be
enabled when multi-ports are conneted: one by one or simultaneously.
This data is used to set the traffic measurement start time for an
operation status report that can be acquired by EP-TRESS only.
This data is used to set the traffic measurement end time for an
operation status report that can be acquired by EP-TRESS only.
Determines whether or not to enable accessibility to the Private Mail Box
(confidential box) using DTMF
To enter a reference password at send side for enabling the DTMF
Relay Broadcast operations.
After completing a send operation using the ISDN line, the network will
inform the transmitter of the accounting data to be charged for the
communication. This data determines which accounting data should be
applied as the charge, the charge sent by the network or the data to be
registered in the individual Speed Dial directory.
Access by
CE
CE
CE
CE
CE
CE
CE
CE
CE
CE
CE