Xerox WorkCentre Pro 423 Service Manual page 233

Chain Function Item
58 180 90 deg. rotation at outputting data or
report
58 181 Smoothing
58 182 Duplex printing on Outputting (received
data print/report print/check print)
58 183 180 deg. Rotation for Side-Two on
outputting SEF paper
58 184 180 deg. Rotation for Side-Two on
outputting LEF paper
58 301 Outputting Activity Report
58 302 Outputting Broadcast Report
58 303 Outputting Relay Broadcast Report
58 304 Outputting Send Fault (Transmission)
Report
58 306 Outputting Transmission report when
transmission is stopped
58 310 Selecting Auto Deletion for polled
documents
WorkCentre Pro 423/428
Description Default
0:Off 1:On 01
0:Off (Simple enlargement) 01
1:On
0:Off 1:On 00
0:Off 1:On 00
0:Off 1:On 00
0:Off 1:On 01
0:Off 1:On 01
0:Off 1:To be sent to the specific 01
station
0:Off 1:On 01
0:Off 1:On 00
00:Not to be deleted 01:To be 00
deleted after comm.
03/02
2-201
Description
When the user can select paper on receiving data as described in
Chain=057 and Function=501, if an appropriate paper (A4SEF or
A4LEF) is not loaded, enable 90 deg. rotation (A4SEF-A4LEF) in
memory to paper that matches the size after repositioning for outputting.
This data determines whether or not to enable the 90° rotation feature.
Main unit's pixel density for recording is 400PPI. When the image data
received is below 400PPI, the image will be stretched to 400PPI during
process. This data determines whether or not to smooth the edge of
binary image at the stretching process.
Duplex printing is available with Duplex Module installed models. This
data determines whether or not to enable unconditional duplex printing
for the information of the same job when outputting data received or
reports. This feature should be handled by individual C/E and any
change will be made by each C/E. (EP-TRESS)
When "On" is selected at Chain=058 and Function=181(Duplex printing
on receiving data or reports), Main unit activates duplex recording based
on the Long Edge Binding. Therefore, when the customer wants to bind
the short edge of SEF paper, select On.
When "On" is selected at Chain=058 and Function=182(Duplex printing
on receiving data or reports), Main unit activates duplex recording based
on the Long Edge Binding. Therefore, when the customer wants to bind
the short edge of LEF paper, select On.
Determines the timing of outputting the Activity Report. When "On" is
selected, the Report will be automatically output when 50
communications of receive and send operations are accumulated.
When the Report is output manually in C/E mode, the latest 50
communication results will be output.
While Outputting Broadcast/Multi-Poll Report as described in Chain=058
and Function=354 specifies an outputting timing for a multi-poll job, this
data specifies how to output a broadcast job.
Specifies an outputting timing for Relay Broadcast Report. As all jobs
received from the relay broadcast station are completed, reports will be
output and send operation will be processed based on this data.
Determines whether or not to inform the operator of the specific send job
error. When "On" is selected for Transmission (Monitor) Report which
was error in communication, Send Fault (Transmission) Report will be
output regardless of the setup status.
When the operator pressed the Stop Button or stopped a send job after it
is enabled, this data determines whether or not to output Send Fault
(Transmission) Report.
Determines how to handle the polled (confidential) documents stored in
memory
How to use the Diagnostic C/E Mode
CHAPTER 2 TROUBLESHOOTING
Access by
CE
CE
CE
CE
CE
User
User
User
User
User
User