Sanken S06-4A005-B Instruction Manual page 97

Note: When the frequency is specified using an analog signal, an appropriate setting should be specified using F1508 to
prevent frequency matching signal from chattering. When the vector control is active, the output frequency
constantly changes. Set F1508 to several Hz.
F1509 Selection of output terminal DO1
F1510 Selection of output terminal DO2
Selection of output terminal DO3
F1511
This function is used to select the required function from the multifunctional output terminals DO1-DO3 of control circuit terminals to
execute open-collector output.
Code No. Function Name
F1509 Selection of output terminal
DO1
F1510
Selection of output terminal
DO2
F1511
Selection of output terminal
DO3
*1 Can not be used together with the current output function. When outputting frequency counter, set F1515 = 0 to disable the
current output function.
Table 7-3 Multifunctional output signals
Data No.
0
1 In operation 1
2 Undervoltage
3 End of simple scheduled operation
4 In operation 2
5 Frequency matching (1st speed frequency)
（※3）
6 Frequency matching (1st to 16th speed
frequencies)（※3）
7
Frequency approach（※3）
8 Overload alarm level setting signal (the
value of F1704)
9 Electric thermistor pre-alarm signal
10 Radiator overheat pre-alarm signal
13 Excitation and DC braking signals
14
Lower frequency limit matching signal（※
3）
15
Upper frequency limit matching signal（※
3）
16
Servo on ready signal
17
Zero servo completion signal
18 signal
FR
19 signal
RR
Unused
0：
Undervoltage
2：
3：End of simple scheduled operation
4：In operation 2
5：Frequency matching (1st speed frequency)
6：Frequency matching (1st to 16th speed frequencies)
7：Frequency approach
Overload alarm level setting signal (the value of
8：
F1704)
9：Electric thermistor pre-alarm signal
10：Radiator overheat pre-alarm signal
13：Excitation and DC braking signals
14：Lower frequency limit matching signal
15：Upper frequency limit matching signal
16： Servo on ready signal (option)
Zero servo completion signal (option)
17：
FR signal
18：
signal
20：2DF
22：5DF signal
24：AD2 signal
signal
26：JOG
signal
28：ES
31： Positioning completion signal (option)
32：Discharge resistor on
34： Frequency counter (output frequency)(※1)
35：Frequency counter (command frequency)(※1)
Overload alarm level setting signal
36：
(Including when in acceleration/deceleration )
42：Torque matching
Low speed detection signal
43：
Motor speed counter
47：
48：Forward run detection signal
49：Reverse run detection signal
Function
Unused terminal.
Inverter in operation (gate signal on) on
Undervoltage alarming ON.
On when simple scheduled operation ends
Inverter in operation (except DC braking and exciting) is (gate signal on) on
ON when the output frequency is equal to target frequency during 1st speed operation.
ON when the output frequency is equal to target frequency during 1st-16th speed operations.
Output frequency is F1507: On when the arrival frequency is exceeded.
Load status during normal operation is F1704: On when the overload pre-alarm value is
exceeded.
ON when the electric thermistor integral value is more than 80% of protection stop value.
ON when radiator overheat protection alarm occurs
ON during DC braking or excitation.
When output frequency is F1008: ON when the lower frequency limit and F1508 are the
same within the frequency matching range.
When output frequency is F1007: ON when the upper frequency limit and F1508 are the
same within the frequency matching range.
ON during position control operation except for during excitation
When the gate pole is ON under zero-servo, the position deviation F8121: ON if below
zero-servo completion range.
ON if the multifunctional input terminal FR is on.
ON if the multifunctional input terminal RR is on.
Data Content
1：In operation 1
signal
19：RR
signal
21：3DF
23：9DF signal
25：AD3 signal
signal
27：MBS
signal
29：RST
signal
signal
(※1)
Action
- 96 -
Setting Resolution Factory Presets
1 1
5
8