Horizon Fitness Bookletmaker SPF-200A Manual page 99

5-1 If an Icon Is Displayed on the Error Screen
100 to 199 SPF Section Jam
132 No Sheet at Jog Section
Jog Section Top and
133
Bottom Guide Step-out
Stitch Section Front Wire
134
Feeding Error
Stitch Section Rear Wire
135
Feeding Error
Jog Section Transport
136
Belt Step-out
Jog Section Transport
137
Error
Jog Section Delivery
138
Error
150 Fold Section Jog Error
151 Fold Section Exit Jam
155 Fold Section Jam
Delivery Error from Fold
156
Section
There were no sheets in the jog section when the stitching operation was done.
The sheets enter into the jog section before the stopper rises. Therefore, the sheets
may not stop at the correct position. Lower the production speed on the Binding-
Operation screen.
There was too much load on the top and bottom guide, or transport pusher, and one
of the parts moved.
Check that only the specified guides and stoppers are attached when you do the
changeover.
There is a problem with the wire feed.
This error is displayed if the preset number of stitching operations has been com-
pleted, or if the wire guide has been detected continuously (wire is tangled), or if the
wire guide has not been detected at all (wire has run out). Check if the wire is strained
from the wire coil to the wire guide.
Check if the wire has run out, or the wire has jammed inside the stitcher head,
Check if a booklet with no stitches has been delivered to the downstream device. If
the problem occurs again although the wire is OK, change the wire feeding detection
setting. (Refer to Section 3-5, step 4.)
On the Administrator Mode screen, set the number of times the machine can miss a
stitch before this error is detected. (Refer to page 31.)
There is a problem with the wire feed.
This error is displayed if the preset number of stitching operations has been com-
pleted, or if the wire guide has been detected continuously (wire is tangled), or if the
wire guide has not been detected at all (wire has run out.) Check if the wire is strained
from the wire coil to the wire guide.
Check if the wire has run out, or the wire has jammed inside the stitcher head.
Check if a booklet with no stitches has been delivered to the downstream device. If
the problem occurs again although the wire is OK, change the wire feeding detection
setting. (Refer to Section 3-5, step 4.)
On the Administrator Mode screen, set the number of times the machine can miss a
stitch before this error is detected. (Refer to page 31.)
There was too much load on the transport pusher, and the position of the transport
pusher has changed.
If there are jammed sheets, remove the sheets. If the transport pusher is discon-
nected, attach the transport pusher. Increase the stitch delay time in Binding-Status
Setting Screen. ( Refer to Section 1-3-8.)
Some sheets remain in the jog section. Remove the sheets. The possible causes are
following.
- This error may be displayed when operating in high production speed, and the trans-
port belt moves to one side.
- The tail edge of the sheets may stay in the exit of the infeed section, and the sheets
are not transported completely. Adjust the angle of the sheet holder. (Refer to Section
4-2.)
Sheet jams in the transport way between the jog section and the fold section.
Remove the sheets.
This error may be displayed if the distance between the jog pushers is too tight in
relation to the sheet size. If the sheets are not jogged in the stitch section, increase
the jogging frequency using the Binding-Status Setting screen. (Refer to page 25.)
If the problem occurs again, increase the distance between the fold knife position and
the jog pusher using the Binding-Fine Adjust-Fold Section screen. (Refer to Section
1-3-7.)
A booklet is jammed in the exit of the fold section. Remove the jammed booklet.
If a sheet is not jammed, the sensor may be dirty. See Section 6-5-3 and clean the
sensor.
A booklet is jammed in the fold section. Remove the jammed booklet. Check if the
buckle gap is too narrow. (Refer to Section 3-3-3.) If a sheet is not jammed, the sen-
sor may be dirty. See Section 6-5-3 and clean the sensor.
A sheet is jammed in the horizontal transport section (if you are not doing folding) or
in the fold section (if you are doing folding). Remove the sheets. If it is difficult to
remove them, remove the sheet guides first. (Refer to Section 5-2.)
When folding thin booklets, raise the fold knife. Also check if the booklet thickness
has been entered correctly.
Cause and Solution
5
91