Horizon Fitness Bookletmaker SPF-200A Manual page 100

5-1
200 to 299 HP-200A Jam
201 Punch Cover Open
Infeed Error to Infeed
211
Section
212 Infeed Section Jam
213 Punch Section Jam
200 to 299 HP-200A Jam
Upstream Device Deliv-
220
ery TIming Error
Sheet Undetected at
230
Punch Section
250 Punch Section Jog Error
Fore-edge Trim Section
300 to 399
Fore-edge Trim Section
301
Emergency Stop
Fore-edge Trim Section
302
Cover Open
Infeed Error to Fore-
313 edge Trim Section
Entrance
Fore-edge Trim Section
314
Entrance Jam
Fore-edge Trim Section
315
Jam
Fore-edge Trim Section
318
Transport Error
Upstream Device Deliv-
320
ery Timing Error
Faulty Set Ejecting
330
Section Jam
Top and Bottom Trim
400 to 499
Section Jam
700 to 799 Downstream Device Error
Downstream Device
700
Error
92
If an Icon Is Displayed on the Error Screen
Close the punch section cover.
The booklet is transported from the upstream device. However, the HP-200A
entrance sensor did not detect the booklet.
The booklet is jammed in the infeed section. Remove the booklet. If a booklet is not
jammed, the sensor may be dirty. See Section 6-5-3 and clean the sensor.
The booklet is jammed in the punch section. Remove the booklet. If a booklet is not
jammed, the sensor may be dirty. See Section 6-5-3 and clean the sensor.
The delivery timing error from the upstream device occurred. If the problem occurs
again, slow down the production speed.
Sheet could not be detected at punch section.
The jog error occurred. This error occurs when a booklet with folding only or a fed booklet
are not arranged properly. First, set the punch delay time longer. If this error occurs repeat-
edly, increase the number of jog. If the jog pusher mis-jogs, increase the jog pusher stroke.
Jam
Turn the Emergency Stop button to release it.
Close the cover.
Although a booklet was delivered from the upstream device, the sensor in the
entrance of the fore-edge section did not detect the booklet. If the booklet stopped
because the distance between the upper and lower infeed belts is too wide, reduce
the distance between the upper and lower infeed belts in the fore-edge trim section.
(Refer to Section 4-5.)
A booklet is jammed at the entrance of the fore-edge trim section. Remove the book-
let. If the problem occurs again, adjust the pressure of the transport belts. (Refer to
Section 4-5.) If a booklet is not jammed, the sensor may be dirty. See Section 6-5-3
and clean the sensor.
A booklet is jammed in the fore-edge trim section. Remove the booklet. If a booklet is
not jammed, the sensor may be dirty. See Section 6-5-3 and clean the sensor.
A booklet may be transported diagonally in the fore-edge trim section. Check that
when using small booklets, the fore-edge trim unit is positioned toward the front as
instructed.
If the booklet is crooked when it hits the stopper, adjust the gap between the transport
belts. (Refer to Section 4-5.)
The distance between the transported booklets was too short. The booklet delivery
operation from the SPF-200A/200L is incorrect. The sheets may not be fed into the
fold section smoothly. Check if there are sheet strips remaining on the sheet path.
If there are no sheet strips remaining, increase the fold section top and bottom guide
stroke using the Binding-Status Setting-Fold/Fore-edge Trim/Conveyor screen.
If the problem occurs again, slow down the production speed.
Remove the sheets.
Refer to the user's manual for TBC-200L.
An error has occurred in a downstream device.
Clear the problem in the downstream device.
Cause and Solution
Cause and Solution
Cause and Solution
Cause and Solution