Toshiba e-STUDIO 5540C Service Manual page 1323

e-STUDIO5540C/6540C/6550C
05/08 Mode Element Sub Element
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner RADF
mode
05 Adjustment Scanner RADF
mode
05 Adjustment Scanner RADF
mode
05 Adjustment Scanner RADF
mode
05 Adjustment Scanner RADF
mode
05 Adjustment Scanner RADF
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Scanner Scanner
mode
05 Adjustment Mode
Item Subitem Code
Image location 3031
adjustment
Reproduction 3032
ratio adjustment
Distortion mode 3033
Shading position 3034
adjustment
Shading position 3035
adjustment
Adjustment of 3040
RADF paper
alignment
Adjustment of 3041
RADF paper
alignment
3042
3043
Leading edge 3044
position
adjustment
Leading edge 3045
position
adjustment
3046
3047
Data transfer of 3203
characteristic
value
3209
Sub- Default
Details
Code value
Secondary scanning 124
direction(scan.section)
Adj. secondary 128
scan.direction
Distortion mode
Original glass 117
RADF 133
Front side 12
Back side 5
Fine adjustment of RADF 50
transport speed
RADF sideways deviation 128
adjustment
Front side 50
Back side 50
Carriage position 128
adjustment during scanning
from RADF (black)
Carriage position 128
adjustment during scanning
from RADF (color)
SLG board -> SYS board
Data transfer of
characteristic value of
scanner / SYS board ->
SLG board
21
Acceptable
RAM Contents
value
68~188 SYS When the value increases by "1", the image shifts
by approx. 0.09 mm toward the trailing edge of the
paper.
0~255 SYS When the value increases by "1", the reproduction
ratio in the secondary scanning direction (vertical
to paper feeding direction) increases by approx.
0.025%.
SYS Moves carriages to the adjustment position.
68~188 SYS 0.09524 mm/step
68~188 SYS 0.09524 mm/step
0~20 SYS When the value increases by "1", the aligning
amount increases by approx. 0.4 mm.
0~20 SYS When the value increases by "1", the aligning
amount increases by approx. 0.4 mm.
0~100 SYS When the value increases by "1", the reproduction
ratio of the secondary scanning direction on
original (fed from the RADF) increases by approx.
0.1%.
0~255 SYS When the value increases by "1", the image of
original fed from the RADF shifts toward the rear
side of paper by approx. 0.0423 mm.
0~100 SYS When the value increases by "1", the copied image
of original fed from the RADF shifts toward the
trailing edge of paper by approx. 0.2 mm.
0~100 SYS When the value increases by "1", the copied image
of original fed from the RADF shifts toward the
trailing edge of paper by approx. 0.2 mm.
0~255 SYS When the value increases by "1", the carriage
position shifts by approx. 0.1 mm toward the exit
side when using the RADF.
0~255 SYS When the value increases by "1", the carriage
position shifts by approx. 0.1 mm toward the exit
side when using the RADF.
SYS Transfers the characteristic values of the scanner
(shading correction factor / RGB color correction /
reproduction ratio color deviation correction /
shading position correction factor / reproduction
ratio correction value in primary scanning direction)
SYS Transfers the characteristic values of the scanner
(shading correction factor / RGB color correction /
reproduction ratio color deviation correction /
shading position correction factor / reproduction
ratio correction value in primary scanning direction)
from the SRAM of the SYS board to the SRAM of
the SLG board.
Proc
ServiceUI
edure
1 Yes
1 Yes
6 Yes
1
1
1
1
1 Yes
1 Yes
1 Yes
1 Yes
1
1
6 Yes
6
Ver11