Toshiba E-STUDIO 5518A Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. All in One Printer
  5. E-STUDIO 5518A
  6. Manual

Toshiba E-STUDIO 5518A Manual

Hide thumbs Also See for E-STUDIO 5518A:
Table of Contents

Advertisement

Quick Links

Job Shops
e-STUDIO8518A Series Job Shops

Advertisement

Table of Contents
loading

Related Manuals for Toshiba E-STUDIO 5518A

Summary of Contents for Toshiba E-STUDIO 5518A

  • Page 1 Job Shops e-STUDIO8518A Series Job Shops...
  • Page 2 e-STUDIO Job Shops...

  • Page 3: Table Of Contents

    Table of Contents Copying .................... 5 Add Paper ......................6 Dual Scan Document Feeder (DSDF) ............7 Bypass Copying ....................9 Automatic Paper Selection (APS) ..............11 Manual Paper Selection ................12 Edge Erase ....................14 1 to 2 Duplex ....................16 2 to 2 Duplex ....................
  • Page 4 Hole Punching....................52 Watermarks ....................53 Poster Print ....................54 Tandem Printing ................... 55 Booklet Printing .................... 57 Saving and Recalling a Print Profile ............59 Center Folding (without staple) ..............61 Store to an e-Filing Box ................62 Print from USB ....................64 Scanning ..................

  • Page 5: Copying

    Copying e-STUDIO Job Shops...

  • Page 6: Add Paper

    Add Paper When a drawer runs out of paper, the drawer display on the touch panel starts blinking. Perform the following steps to add paper to a drawer. 1. To add/replace paper: a) Pull out the drawer 2. Open the ream of paper and remove any creased sheets.

  • Page 7: Dual Scan Document Feeder (Dsdf)

    Dual Scan Document Feeder (DSDF) In this job shop you will use the Dual Scan Document Feeder (DSDF) to make copies. Do not use the following types of originals in the document feeder since they may cause misfeeding or damage to the system: •...
  • Page 8 Dual Scan Document Feeder (continued) 3. Tap Paper Select or touch the trays on the image of the copier near the bottom of the screen. 4. Select copy settings if desired. 5. Press the green Start hard button. Note: If you need to stop copying, tap the red Stop button on the touch screen, and then press the Orange Function Clear button.

  • Page 9: Bypass Copying

    Bypass Copying In this job shop you will use the stack bypass of the e-STUDIO to copy onto thick LT-R (landscape orientation) paper. Use the bypass tray to make copies on specialty media like card stock, OHP transparency film or non-standard size paper.
  • Page 10 Bypass Copying (Continued) 6. When paper is placed in the bypass tray, the control panel displays the menu for bypass settings. 7. Under the ORIGINAL and COPY columns, Tap the LT in both columns. 8. Tap Paper Type. 9. Tap Thick 2 (~110lbs index). 10.

  • Page 11: Automatic Paper Selection (Aps)

    Automatic Paper Selection (APS) In this job shop, you will use the e-STUDIO’s APS feature. 1. Place the originals you want to copy in the Dual Scan Document Feeder. If the e-STUDIO isn’t in Copy Mode, access the Copy mode screen.

  • Page 12: Manual Paper Selection

    Manual Paper Selection This job shop will explain that sometimes APS cannot be used. You will practice how to select Manual Paper Selection. You cannot select Automatic Paper Selection (APS) for the following originals because their sizes cannot be detected accurately: •...
  • Page 13 Manual Paper Selection (Continued) 4. Select other modes as required, and then press the green Start Hard button. 5. Follow the prompt in the message area of the screen. 6. When you have finished scanning the originals, press Job Finish. e-STUDIO Job Shops...

  • Page 14: Edge Erase

    Edge Erase (Copying > Basic Copying) Sometimes a dark edge appears outside a copied image. This can be caused by a gap between the original glass and the platen sheet. You can delete this shadow on copies using a function called edge erase. This feature is especially useful when you are making copies of thick heavy cardstock or bound originals.
  • Page 15 Edge Erase (Continued) 4. Tap Edge Erase. 5 Adjust the width of the desired amount of edge to be erased using the up and down arrows. 6. Tap OK. 7. Tap the START button. e-STUDIO Job Shops...

  • Page 16: To 2 Duplex

    1 to 2 Duplex In this job shop, you will perform the following steps to copy one-sided originals and produce two-sided copies. 1. Place several originals in the automatic document feeder. 2. On the HOME screen, tap Copy. 3. Tap 2-SIDED on the touch screen.

  • Page 17: To 2 Duplex

    2 to 2 Duplex In this job shop, perform the following steps to copy a two-sided original and produce a two- sided copy. 1. Place a 2-sided original in the automatic document feeder. 2. Tap 2-SIDED on the touch screen. 3.

  • Page 18: To 1 Split

    2 to 1 Split Perform the following steps to copy a two-sided original and produce one-sided copies. 1. Place a 2-sided original in the Document Feeder 2. On the HOME screen, tap Copy 3. Tap 2-SIDED on the touch panel. 4.

  • Page 19: Book To 2

    Book to 2 (Copying > Duplex Copying) Perform the following steps to copy a book-type original and produce a two-sided copy. 1. On the HOME screen, tap Copy. 2. Tap 2-SIDED on the touch panel. 3. Tap BOOK -> 2. e-STUDIO Job Shops...
  • Page 20 3. Select the appropriate book copying options to reflect where the start and end pages of the section of the book that you are copying are located (one of four choices). Right indicates that the first page of the section of the book being copied and the last page and last page are both on the right.
  • Page 21 Book to 2 (Continued) 6. Tap the START button. 7. When the opened pages have been scanned, place the next pages of the book on the glass, and tap the START button again. 8. When all the pages have been scanned, tap Finished on the touch panel.

  • Page 22: Ams Enlargement And Reduction Copying

    AMS Enlargement and Reduction Copying (Copying > Advanced Copying) If you specify the copy paper size in advance, the equipment will detect the original size and automatically select the optimal reproduction ratio for the copy paper size. Perform the following steps to enlarge or reduce an original. (AMS = Automatic Magnification Selection) 1.

  • Page 23: Background Adjustment

    Background Adjustment This function lets you adjust the density of the original’s background. It avoids the back side of a 2-sided original becoming visible on its front side. 1. Access the Copy mode screen 2. Tap the Image tab. 3. Tap Background Adjustment. e-STUDIO Job Shops...
  • Page 24 Background Adjustment (Continued) 4. Tap Light three times to adjust the density. 5. Tap OK. 6. Press START to make a copy. 7. Repeat steps 1 through 3. 8. This time, tap Dark three times to adjust the density. 9. Press START to make a copy. Compare the Light copy with the Dark copy.

  • Page 25: Sharpness

    Sharpness This function allows you to emphasize or blur the outline of an image. Access the Copy mode screen. 2. Tap the Image tab 3. Tap the Sharpness button on the image menu. e-STUDIO Job Shops...
  • Page 26 Sharpness (Continued) Tap the Sharp button three times to increase the sharpness. 5. Tap OK. Press START to make a copy 7. Repeat the steps 1 to 3 above and this time tap Soft three times to reduce sharpness of copy. 8.

  • Page 27: Proof Copy

    Proof Copy This function lets you check copy density, zoom, margin width, and other settings by making only one set of copies before continuing a large copy job. 1. Place the originals face up in the automatic document feeder and adjust the feed guides.
  • Page 28 Proof Copy (Continued) 5. Tap the Proof Copy button. 6. Press the START button to print one proof copy of the original. If needed, change the settings as required and press the START button again. e-STUDIO Job Shops...

  • Page 29: Job Build

    Job Build You can scan several stacks of originals whose settings are individually different, and then copy or store them in one operation. Note: You can scan up to 1000 pages of originals in one operation. There is no limit to the number of jobs. Note: Some settings are not available in job build, and some settings when applied to the first job will be applied to all the other jobs.
  • Page 30 Job Build (continued) 4. Tap the OK button. Job build is now set and the message “Tap START button to copy after changing settings” appears in the message indication area on the touch panel. Place the first stack of originals in the automatic document feeder and adjust side guides.
  • Page 31 Job Build (continued) Place the next stack of originals and select the desired settings. Repeat steps 6 & 7 until all originals have been scanned. Note: If you do not change the settings, those from the last job will be applied. Tap the Job Finish button to complete the copy job.

  • Page 32: Simple Copy

    Simple Copy The e-STUDIO provides an independent menu called “Simple Copy” so that you can make copies with minimum operations. 1. On the HOME screen, tap the Simple Copy button. 2. Tap the Staple button. Then select Upper Right. 3. For the number of Sets, tap the “+”...

  • Page 33: Automatic Stapling

    Automatic Stapling With an optional Finisher, in the staple/sort mode, you can select from three stapling positions. Perform the following steps to select automatic stapling for your copies. 1. After tapping the Copy button on the HOME screen, tap Finishing on the touch panel. 2.

  • Page 34: Hole Punching

    Hole Punching With the optional Hole Punch unit, the e-STUDIO can place 3-holes or 2-holes on the edge of the copies. 1. After tapping the Copy button on the Home screen, tap Finishing on the touch panel. 2. Tap Hole Punch (Middle Left) 3.

  • Page 35: Original Mode

    Original Mode You can make copies with optimal image quality by selecting the best mode for your original text or photo. 1. Tap Original Mode button. 2. Select the desired original mode. Note: The original modes differ depending on the color mode set. 2.
  • Page 36 e-STUDIO Job Shops...

  • Page 37: Printing

    Printing In the following job shops, you will practice using the e-STUDIO printing features. Read this before you begin: Your instructor will provide you with sample files to use/print for the following job shops. These instructions use a Microsoft operating system with Microsoft Word 2016 for Office 365 document.

  • Page 38: Accessing The Microsoft Word Print Dialogue Window

    Accessing the Microsoft Word Print Dialogue Window This lesson will explain how to select a Toshiba Print Driver to use for printing the Print job shops. 1. Access the MS Word print dialogue window, click File, then click Print or CTRL + P 2.

  • Page 39: Double-Sided Printing

    Double-Sided Printing In this job shop you use the e-STUDIO’s print driver to print a multi-page document on both sides of the paper. 1. With a multi-page file, click the Finishing tab. 2. Click desired icon representing your desired duplex printing style and orientation.

  • Page 40: Stapling Print Jobs

    Stapling Print Jobs In this job shop, you will practice stapling documents utilizing the e-STUDIO’s printer driver. (Stapling is available only if an optional Finisher is installed.) 1. Click the Finishing tab. 2. Click the icon representing how to staple, either upper left, upper right, center top, middle left, or center double.

  • Page 41: Multiple Pages Per Sheet

    Multiple Pages Per Sheet In this job shop, you will print multiple pages on one 1 sheet of paper. You will need a least a four-page file (MS Word, PDF, etc.) to complete this job shop. This feature is useful for browsing many pages for appearance or page order and conserves paper.

  • Page 42: Offset Sorting

    Offset Sorting Perform the following steps to produce multiple sets of off-set (rotated orientation) sorted print output. 1. On the Basic tab, enter 5 for the Number of Copies. 2. Click the Finishing tab. 3. Click the Rotated Sort icon. 4.

  • Page 43: Sorting Print Output

    Sorting Print Output Produce multiple sets of sorted print output. 1. On the Basic tab enter the number 5 in the Number of Copies box. Click the Finishing tab. 3. Click the Sort Copies icon. Set additional print options and click OK.

  • Page 44: Proof Print Jobs

    Proof Print Jobs Proof print is a feature that lets you print one set as a proof (sample) print when you are printing a multiple sets of a file. 1. Click the Basic tab on the, Set Number of Copies to print 3 sets. 3.
  • Page 45 Proof Print Jobs (Continued) 7. Tap the Job Type drop down arrow. Then select Proof from the menu. 8. Select the desired job. Then tap Print. e-STUDIO Job Shops...

  • Page 46: Hold Print Job

    Hold Print Job The Hold Print function allows the printer to retain your document in the Hold Print job list until you print it from the touch panel. This function is useful to prevent users from forgetting to remove printed documents. From the Basic tab, click the Print Job drop down box.
  • Page 47 Hold Print Job (Continued) 5. At the e-STUDIO MFP press the Print button on the HOME screen Select Hold from the Job Type drop-down menu on the touch panel. Select your username. Your username is usually your Windows logon name. 8.

  • Page 48: Private Print Jobs

    Private Print Jobs The Private Print Jobs function is ideal for printing confidential documents. Private Print is like Hold Print, with the addition of password protecting a file held in the e-STUDIO. 1. From the Basic tab, click the Print Job drop down arrow. 2.
  • Page 49 Private Print Jobs (Continued) 10. At the prompt, enter the same password you used to print your document. 11. Then press the OK button 12. Select the desired job. 13. Tap the Print button. e-STUDIO Job Shops...

  • Page 50: Scheduled Printing

    Scheduled Printing The Scheduled Print feature lets you specify the date and time to print your job. With this feature, you can schedule large jobs to print during off-peak hours. 1. Click the Print Job drop-down box. 2. Click Scheduled Print. 3.
  • Page 51 Scheduled Printing (Continued) 4. On the Scheduled Print pop-up dialog window: a) Click the Date drop-down arrow to change the date for your print job to print. b) Click the Time drop-down arrow to change the time for your print job to print. c) Click OK 5.

  • Page 52: Hole Punching

    Hole Punching Hole punching is available only if an optional Finisher and Hole Punch unit is installed. Perform the following steps to punch holes on printed sheets of paper as they exit from the system. 1. Click the Finishing tab. 2.

  • Page 53: Watermarks

    Watermarks Use watermarks to overlay your document with text such as, “Confidential” or “Draft”. You can choose from several styles of watermarks or you can create and save your custom designs. 1. Click the Effect tab. 2. Click the Watermark drop-down box.

  • Page 54: Poster Print

    Poster Print You can divide a print job across multiple sheets of paper to create one large image, such as a poster, by connecting the divided images. Click the Finishing tab. Select the Poster Print check box. Click the Details button. Select the Output number of Sheets.

  • Page 55: Tandem Printing

    Tandem Printing Print one multiple set print job to two different e-STUDIOs simultaneously. NOTE: You will need to have print access to another e-STUDIO to complete this job shop. Set the Number of Copies to 3 on the Basic tab. (Image not shown) Click the Others tab.
  • Page 56 Tandem Printing (Continued) Select Devices to use from the drop-down menus. Tip: Equipment selected in the Selected Devices boxes must be registered in Printer Folder. If you want to use equipment not registered in Printer Folder, add it in Add Printer on the Others tab of the Printer driver.

  • Page 57: Booklet Printing

    Booklet Printing Printing in the booklet mode produces a document that can be folded to become a paginated booklet or magazine-style publication. You can even create bound booklets that are folded and stapled in the center. Note: The folding option is only available when the Saddle Stitch finisher is installed. 1.
  • Page 58 Booklet Printing (Continued) 4. Click the Output Document Layout drop-down box and select LT on LD. 5. To double-staple the center, click the Staple Down the Center box. The Folding checkbox will be selected automatically. Click OK to close the window. 6.

  • Page 59: Saving And Recalling A Print Profile

    Saving and Recalling a Print Profile Profiles are useful when frequently using the same print settings. 1. After completing the previous job shop, “Booklet Printing,” go back into the Print Properties (click Print > {Select the same printer you used in the previous job shop} >...
  • Page 60 Saving and Recalling a Print Profile (Continued) 8. Clear all those current print settings • Click the Others tab • Click Restore all Defaults • Click OK to the popup window Notice how all the print settings for making a booklet have disappeared. (It may show a duplexed sheet of paper because that is the factory default).

  • Page 61: Center Folding (Without Staple)

    Center Folding (without staple) This option folds the printed paper down the horizontal center of the paper when it exits the machine. Note: The folding option is only available when Saddle Stitch finisher is installed. 1. On the Basic tab, click Landscape. (This folds it with the images in Portrait orientation).

  • Page 62: Store To An E-Filing Box

    Store to an e-Filing Box This feature lets you store print jobs to e-Filing boxes on the system. The jobs can then be printed from the touch panel at a later time or inserted into other documents. You can select either a public box or user box to store print jobs From the Basic tab, click the Print Job drop down box.
  • Page 63 Store to an e-Filing Box (Continued) If Public Box is not selected, click the Store to: drop-down box and select the Public Box. 6. For Box Folder: name enter your name. 7. Click OK. Set additional print options and click OK. Click Print on the next window to send your file to the printer.

  • Page 64: Print From Usb

    Print from USB Printing from USB lets you print PDF, Encrypted PDF, JPEG, XPS, PRN (.PRN) and PostScript (.PS) print files stored on a memory stick connected to the system’s USB port 1. Connect USB storage device to the USB port on the NOTE: The e-STUDIO’s USB port, depending on the model, is system.
  • Page 65 Print from USB (Continued) In the list of files, select a file to print. Note: If you have an encrypted PDF file that requires a password, you will be prompted to enter the password at this point. Tap SETTINGS. Select desired print options, including number of sets/copies.
  • Page 66 e-STUDIO Job Shops...

  • Page 67: Scanning

    Scanning e-STUDIO Job Shops...

  • Page 68: Simple Scan

    Simple Scan With this equipment, “Simple Scan”, which is an exclusive operation screen, is prepared so that you can scan images using only the minimum steps. For this activity, you will scan a document to your email address or other valid email address. 1.
  • Page 69 Simple Scan (continued) 4. Tap Auto Color. 5. Tap Resolution. 6. Set the resolution to 300dpi. e-STUDIO Job Shops...
  • Page 70 Simple Scan (continued) 7. Tap Address Book. 8. In the bottom left corner, Tap To+ to input an email address manually. 9. Tap Direct Input. e-STUDIO Job Shops...
  • Page 71 Simple Scan (continued) 10. Use the onscreen keyboard to type your email address. 11. Tap Start to scan your document. e-STUDIO Job Shops...

  • Page 72: Scan To E-Mail

    Scan to E-mail scan to e-mail feature lets you send large scans to specified e-mail addresses. The scanned image is converted to a PDF, XPS, TIFF, or JPEG file and sent as an e-mail attachment. 1. Place originals face up in the Dual Scan Document Feeder.
  • Page 73 Scan to E-mail (Continued) 4. You can select e-mail addresses in various ways. For this exercise, you will use your own email address and you will also select an email address from the e-STUDIO’s Address Book. Tap the keypad icon. 5.
  • Page 74 Scan to E-mail (Continued) 7. Tap the single person icon. Tap All. 8. Tap a contact from the address book. Tap OK. 9. Tap Detail to add some additional information to this scanned file. 10. Specify the appropriate settings on the screen: •...
  • Page 75 Scan to E-mail (Continued) 11. Tap Scan Settings to enter any additional scan settings you require and tap OK. 12. To start the scan, tap Scan on the touch panel or the green Start hard button on the control panel. DO NOT press FUNCTION CLEAR 13.
  • Page 76 Creating and Using Scan Templates Users can configure a Template button with copy, fax, or scan settings. This can make it easier and more accurate for users to accomplish routine tasks. In this job shop, you will use the scan to email settings that you programmed for the previous job shop.
  • Page 77 Creating and Using Scan Templates (continued) 5. Tap a blank box. Tap Save. 6. Use the on-screen keyboard to type a name for your template button. Type a name so you will recognize the function of the template. You can edit both Name1 and Name2.
  • Page 78 Creating and Using Scan Templates (continued) Now you will use the template. 9. Clear all the scan settings by tapping Function Clear twice. 10. Place originals face up in the document feeder. 11. On the Home screen, tap Scan. e-STUDIO Job Shops...
  • Page 79 Creating and Using Scan Templates (continued) 12. Tap Template. 13. Tap the (your) Template Group. 14. Tap the Template button that you created for scanning to email. 15. Check your email for the attachment. e-STUDIO Job Shops...

  • Page 80: Scan To Usb

    Scan to USB (Scanning > Scan to File or USB) You will perform the following steps for scanning to a USB storage device. Later, in different job shop, you will print the file you will have scanned to USB. IMPORTANT: Never insert the USB storage device before the e-STUDIO is powered on.
  • Page 81 Scan to USB (Continued 4. When “Found USB DEVICE.” message appears on the touch panel, tap USB. 5. Define the settings for the File Name and File Format and tap OK. 6. To complete the scan, tap SCAN or the green Start hard button. 7.

  • Page 82: Scan To File

    Scan to File The Scan to File sends and stores the scans to the shared folder in the system’s hard disk or a specified network folder. The data stored in the shared folder can be accessed directly from the computer via the network. In this job shop, you will scan a document to the file_share folder on the e-STUDIO’s hard disk drive.
  • Page 83 Scan to a File (Continued) 4. To store the scanned image in a in the e-STUDIO’s shared folder, Select the MFP Local button. (It is selected by default). 5. Tap File Name. Tap Clear on the keyboard to erase the current file name.
  • Page 84 Scan to a File (Continued) 8. Continue this job shop at your computer. Note: The next steps to complete this job shop are instructions when using the Windows 2010 operating system 9. At your workstation, click the Windows Start button. a) Begin typing (the Search box will appear) the IP address of the e- STUDIO that you used, preceded...

  • Page 85: Setting Up E-Filing Boxes

    Setting up e-Filing Boxes The e-Filing feature lets you store, print, and manage documents that you have obtained by copying, scanning, printing from a PC, receiving as a regular fax, and receiving as an Internet fax. The Public user box is a default setting for storing shared documents and can be accessed by all users without restriction.
  • Page 86 Set Up e-Filing Boxes (Continued) 5. Tap BOX NAME (empty) field and enter your name for the box name using the on-screen keyboard. 6. After typing your name for the e-Filing Box, tap OK. Tap PASSWORD and enter a five-digit password (if desired) using the on-screen keyboard.

  • Page 87: Scan To E-Filing

    Scan to e-Filing (e-Filing > Scan to e-Filing) Perform the following steps to scan a document and store it the e-FILING box you created in the previous job shop. Place the original on the glass or in the automatic document feeder.
  • Page 88 Scan to e-Filing (Continued) Tap Box/Folder. Tap your user box (created in previous job shop) in which you want to store the document. Since a password has been set for the selected user box in this exercise, the password entry screen appears.
  • Page 89 Scan to e-Filing (Continued) 7. Tap OK. 8. Change the Document Name if necessary, using the on-screen keyboard, and then tap OK. 9. Tap OK. e-STUDIO Job Shops...
  • Page 90 Scan to e-Filing (Continued) 10. Tap Scan. 11. If you placed the original on the ollow the prompt in platen glass, f the message area of the screen. 12. When you have finished scanning the originals, t ap Job Finish. e-STUDIO Job Shops...

  • Page 91: Print Stored E-Filing Documents

    Print Stored e-Filing Documents Once you have documents stored in e-Filing user boxes, you can print part or all of a document. 1. Tap the e-FILING button on the control panel. 2. On the touch panel, tap the user box that contains the document you want to print.
  • Page 92 Print Stored e-Filing Documents (Continued) the thumbnail button to preview thumbnail images of the documents 5. Tap the document you want to print. 6. Tap Open. Settings. 8. Change the print settings as desired and then tap Print. e-STUDIO Job Shops...

  • Page 93: Previewing Scans

    Previewing Scans With the preview feature, you can view your scans on the touch panel before saving or emailing them. 1. Place a multi-page document in the DSDF. Tap the Scan button on the control panel. There are five different scan modes.
  • Page 94 Previewing Scans (Continued) Tap Preview on the scan menu screen. Then tap Scan. Your scanned pages will be displayed. 7. Go the next job shop to practice managing the previewed pages. e-STUDIO Job Shops...

  • Page 95: Delete, Replace, And Insert Pages

    Delete, Replace, and Insert Pages During Scan Preview mode, perform the following steps to delete, replace, or insert pages into a scanned document. Note: This job shop is a continuation of the previous job shop, “Previewing Scans.” 8. Tap one of the displayed pages.

  • Page 96: Confirm Scan Status

    Confirm Scan Status Perform the following steps to confirm a scan job status. Tap JOB STATUS on the touch panel. Tap the Log tab. Tap Scan. The list includes each job’s destination/file name, agent (scan function), date and time, number of pages, and status (job result).

  • Page 97: Embedded Ocr

    Embedded OCR With the optional OCR Enabler, you can use the Optical Character Reader (OCR). This function can recognize the characters written on your original and output them as text data. When you enable OCR, you can save the text data as a PDF, XPS, DOCX, XLSX or PPTX file.
  • Page 98 Embedded OCR (Continued) 4. Tap the keypad icon your email address 5. Using the onscreen keyboard, type your email address. Then tap Close. 6. Tap Detail to add some additional information to this scanned file. e-STUDIO Job Shops...
  • Page 99 Embedded OCR (Continued) 7. Specify the appropriate settings on the screen: • Subject • Body information • File Name 8. Select the following: • File Format: DOCX • Multi/Single: Select either single (single page file) or multi (multiple page file) 9.
  • Page 100 Embedded OCR (Continued) 11. To start the scan, tap Scan on the touch panel or the green Start hard button on the control panel. Important Notes: • Depending on the conditions of your originals and the requirements for reading, OCR may not recognize characters and figures properly. •...

  • Page 101: Maintenance

    Maintenance e-STUDIO Job Shops...

  • Page 102: Replace Toner Cartridges: E-Studio8518A

    Replace Toner Cartridges: e-STUDIO8518A The system displays a message in the touch panel when you should replace a toner cartridge. You can add the cartridges to the system while it is turned on. Caution: Ask a person who has experience with replacing the toner cartridge for assistance. Although, this is a safe and easy procedure to perform, it might be messy for a person doing this for the first time.
  • Page 103 Replace Toner Cartridges e-STUDIO8518A (Continued) 4. Remove the protective sheet from the end of the cartridge. 5. Insert the new toner cartridge until its front surface aligns to the left side wall. 6. Close the toner cover. In a few seconds, the system will be ready to use.

  • Page 104: Replace Toner Cartridge: E-Studio8518A

    Replace Toner Cartridge: e-STUDIO8518A The system displays a message in the touch panel when you should replace a toner cartridge. You can add the cartridges to the system while it is turned on. Caution: Ask a person who has experience with replacing the toner cartridge for assistance. Although, this is a safe and easy procedure to perform, it might be messy for a person doing this for the first time.
  • Page 105 Replace Toner Cartridge e-STUDIO8518A (Continued) 4. Insert the new toner cartridge. 5. Clean the charger. 6. Close the front cover. e-STUDIO Job Shops...

  • Page 106: Blinking Graphic Symbols

    Blinking Graphic Symbols Sometimes, graphic symbols will blink, or messages appear on the e-STUDIOs, guiding you to take specific actions to resolve a problem or issue. Look for messages on the alert message indication area on the touch screen. 1. Out of paper - When a drawer runs out of paper, the drawer display on the touch panel starts blinking and the message "Add...
  • Page 107 e-STUDIO Job Shops...
  • Page 108 TOSHIBA AMERICA BUSINESS SOLUTIONS, INC ELECTRONIC IMAGING DIVISION Education & Development Group 25530 Commercentre Drive Lake Forest, CA 92630 sales.training@tabs.toshiba.com Toshiba America Business Solutions, Inc. © 2021 e-STUDIO Job Shops...

This manual is also suitable for:

E-studio 6518aE-studio 7518aE-studio 8518a

Table of Contents